Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1985 Ford E350, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
HEATER HOSE MAY BE INCORRECTLY ROUTED. Remedy: REROUTE AND REPAIR HOSE AS NECESSARY.
EXTREME OPERATING CONDITIONS COULD CAUSE PREMATURE DETERIORATION OF THE ENGINE COMPARTMENT HEATER HOSES OR ENGINE BYPASS HOSES. Remedy: REPLACE HOSES AND RADIATOR CAPS; INSTALL HIGH HEAT RESISTANCE ALUMINIZED STAINLESS STEEL MUFFLERS.
HEATER HOSE MAY BE INCORRECTLY ROUTED. Remedy: REROUTE AND REPAIR HOSE, AS NECESSARY.
THE RUBBER THAT ENCASES BALL STUD AND SOCKET JOINT (CONNECTS STEERING DRAG LINK AND PITMAN ARM) MAY DETERIORATE, CAUSING METAL TO METAL CONTACT, AND MAY EVENTUALLY RESULT IN COMPLETE SEPARATION. CONSEQUENCE OF DEFECT: COMPLETE SEPARATION OF THE DRAG LINK TO PITMAN ARM CONNECTION RESULTS IN LOSS OF STEERING CONTROL WHICH MAY LEAD TO AN ACCIDENT. Remedy: INSTALL NEW DRAG LINK ASSEMBLIES WITH STEEL BALL AND SOCKET JOINTS AT THE PITMAN ARM CONNECTIONS.
FUEL LEAK AT THE TOP OF THE FRONT FUEL TANK IN THE AREA OF THE VAPOR VALVE GROMMET. GROMMET MAY SPLIT DUE TO COMPRESSIVE LOAD WHEN INSTALLED IN THE FUEL TANK. Remedy: INSTALLATION OF A NEWLY DESIGNED VAPOR VALVE GROMMET.
WHEN FRONTALLY IMPACTED INTO A FIXED BARRIER AT 30 MPH, AS SPECIFIED IN FEDERAL MOTOR VEHICLE SAFETY STANDARD (FMVSS) NO. 301, THE LEFT FRAME RAILS OF SUCH VEHICLES MAY DISPLACE INBOARD, PINCHING THE FUEL/WATER SEPARATOR CANISTER BETWEEN THE FRAME RAIL AND ENGINE SUFFICIENTLY TO DISPLACE THE FUEL/WATER SEPARATOR DRAIN ROD, ALLOWING THE CONTENTS OF THE CANISTER TO DRAIN. CONSEQUENCE OF DEFECT: FUEL LEAK DURING OR AFTER A CRASH INCREASES THE POSSIBILITY OF A FIRE. Remedy: INSTALL A CANISTER SHIELD, A REVISED DESIGN DRAIN ROD SHIELD, AND MODIFY FUEL/WATER SEPARATOR MOUNTING BRACKET.
VEHICLES ARE SUBJECT TO EXCESSIVE UNDERHOOD TEMPERATURES AND FUEL SYSTEM PRESSURES IN SEVERE DUTY APPLICATIONS. Remedy: INSTALL MODIFICATION KITS TO MINIMIZE POSSIBILITY OF FUEL EXPULSION AND TO SHIELD UNDERBODY COMPONENTS FROM EXHAUST SYSTEM HEAT.
NYLON TIES THAT SUPPORT THE MAIN WIRING HARNESS TO THE CHASSIS COULD WEAR AND BREAK DUE TO EXCESSIVE VIBRATION. THUS, WIRING HARNESS COULD FALL ON ENGINE COMPONENTS AND SHORT CIRCUIT. Remedy: INSTALL RETROFIT RIT OF PLASTIC-COATED METAL CLAMPS, LOOM FOR POSITIVE BATTERY CABLES AND RE-ROUTE WIRING.
EXPULSION OF FUEL DUE TO OVERPRESSURIZATION. Remedy: MODIFICATION OF THE BASE FUEL VENTING AND EMISSION CONTROL SYSTEM TO REDUCE OPERATING TEMPERATURES AND FUEL SYSTEM PRESSURES.
COMPOSITE GRAPHITE DRIVESHAFTS ARE SUBJECT TO OVERHEATING WHILE IDLING, WHICH MAY RESULT IN THE DRIVESHAFT TWISTING AND SHORTENING CAUSING THE SLIP YOKE TO DISCONNECT FROM THE TRANSMISSION. CONSEQUENCE OF DEFECT: IF THE DRIVESHAFT DISCONNECTS FROM THE TRANSMISSION THE VEHICLE WOULD BECOME IMMOBILE WITHOUT WARNING. Remedy: INSTALL METAL DRIVESHAFT.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
THE AIR DEFLECTOR MAY BE INADEQUATELY BONDED TO THE TRUCK BODY AND MAY SEPARATE AT HIGH SPEED. A DETACHED DEFLECTOR COULD BE HAZARDOUS TO OTHER VEHICLES. CORRECTION: AIR DEFLECTORS WILL BE INSPECTED FOR SIGNS OF SEPARATION. IF SIGNS OF SEPARATION ARE FOUND, THE DEFLECTOR WILL BE REFASTENED USING RIVETS.
EXTREME OPERATING CONDITIONS COULD CAUSE PREMATURE DETERIORATION OF THE ENGINE COMPARTMENT HEATER HOSES OR ENGINE BYPASS HOSES. ENGINE COOLANT COULD DISCHARGE ONTO THE ENGINE AND ITS EXHAUST MANIFOLD CREATING THE POTENTIAL FOR A FIRE DUE TO HIGH ENGINE EXHAUST MANIFOLD TEMPERATURES. CORRECTION: HOSES AND RADIATOR CAPS WILL BE REPLACED AND ON CERTAIN VEHICLES, A HIGH HEAT RESISTANCE ALUMINIZED STAINLESS STEEL MUFFLER WILL BE INSTALLED.
1983-87 E-250 AND 350 WITH 7.5 LITRE AND 1985-87 HEAVY DUTY E-250 AND 350 WITH 5.8 LITRE 4V ENGINE AND A GVW OVER 8,500 LBS. THESE VEHICLES HAVE BEEN DETERMINED TO GENERATE EXCESSIVE UNDERBODY TEMPERATURES AND FUEL SYSTEM PRESSURES IN SEVERE DUTY APPLICATIONS, PARTICULARLY IF FUELED WITH OVERLY VOLATILE GASOLINE. THIS CAN CREATE AN ABNORMAL POTENTIAL FOR EXPULSION OF LIQUID FUEL FROM THE FILLER PIPE UPON REMOVAL OF THE FUEL TANK FILLER CAP. IN THE PRESENCE OF AN IGNITION SOURCE, A VEHICLE FIRE COULD OCCUR. CORRECTION: VEHICLES WILL BE MODIFIED TO MINIMIZE THE POSSIBILITY OF FUEL EXPULSION AND SHIELD UNDERBODY COMPONENTS FROM EXCESSIVE UNDERBODY HEAT. NOTE: E250 AND 350 CLUB WAGONS AND ECONOLINE VANS AND CHASSIS.
ON AMBULANCES EQUIPPED WITH 7.5 LITRE ENGINES,VARIOUS FACTORS MAY CAUSE EXCESSIVE UNDERBODY TEMPERATURES OR FUEL SYSTEM OVERPRESSURIZATION WHICH COULD RESULT IN FUEL LEAKS OR EXPULSION OF FUEL FROM THE FILLER PIPES WHEN THE FILLER CAPS ARE REMOVED. IN THE PRESENCE OF AN IGNITION SOURCE A VEHICLE FIRE OR INJURIES COULD RESULT. CORRECTION: THE FUEL VENTING AND EMISSION CONTROL SYSTEMS WILL BE MODIFIED AND VEHICLES INSPECTED FOR SIGNIFICANT DISCREPANCIES.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
UNDER CERTAIN LOW SPEED TIGHT TURNING CONDITIONS UNDER HIGH LOAD, THE RUBBER WITHIN THE RUBBER ENCASED BALL STUD AND SOCKET JOINT CONNECTING THE STEERING DRAG LINK AND PITMAN ARM MAY DETERIORATE CAUSING GALLING OF THE BALL STUD AND SOCKET.THIS COULD EVENTUALLY LEAD TO SEPERATION OF THE DRAG LINK AND PITMAN ARM AND LOSS OF STEERING. CORRECTION:DRAG LINK ASSEMBLIES WITH STEEL BALL AND SOCKET JOINTS WILL BE INSTALLED.
E350 RV AND COMMERCIAL CUTAWAY ECONOLINE VEHICLES. SOME VEHICLES WHERE COMPLETED WITH BODIES WHICH RESTRICTED THE DISSAPATION OF UNDERBODY HEAT.IN SUCH A CASE EXTENDED IDLING COULD OVERHEAT THE COMPOSITE GRAPHITE DRIVESHAFT AND,IF A HIGH START UP TORQUE APPLIED,TWIST AND SHORTEN THE DRIVESHAFT CAUSING THE SLIP YOKE TO DISCONNECT. CORRECTION:METAL DRIVESHAFTS WILL BE INSTALLED.
THESE VEHICLES (VANS AND CLUB WAGONS) DO NOT COMPLY WITH C.M.V.S.S. 301-FUEL SYSTEM INTEGRITY.