Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1985 Ford Econoline, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK. Remedy: FEDERAL-MOGUL WILL NOTIFY OWNERS AND REPLACE THE DEFECTIVE FUEL PUMPS FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 15, 2007. OWNERS CAN CONTACT FEDERAL-MOGUL AT 248-354-7700.
WHEN FRONTALLY IMPACTED INTO A FIXED BARRIER AT 30 MPH, AS SPECIFIED IN FEDERAL MOTOR VEHICLE SAFETY STANDARD (FMVSS) NO. 301, THE LEFT FRAME RAILS OF SUCH VEHICLES MAY DISPLACE INBOARD, PINCHING THE FUEL/WATER SEPARATOR CANISTER BETWEEN THE FRAME RAIL AND ENGINE SUFFICIENTLY TO DISPLACE THE FUEL/WATER SEPARATOR DRAIN ROD, ALLOWING THE CONTENTS OF THE CANISTER TO DRAIN. CONSEQUENCE OF DEFECT: FUEL LEAK DURING OR AFTER A CRASH INCREASES THE POSSIBILITY OF A FIRE. Remedy: INSTALL A CANISTER SHIELD, A REVISED DESIGN DRAIN ROD SHIELD, AND MODIFY FUEL/WATER SEPARATOR MOUNTING BRACKET.
VEHICLES ARE SUBJECT TO EXCESSIVE UNDERHOOD TEMPERATURES AND FUEL SYSTEM PRESSURES IN SEVERE DUTY APPLICATIONS. Remedy: INSTALL MODIFICATION KITS TO MINIMIZE POSSIBILITY OF FUEL EXPULSION AND TO SHIELD UNDERBODY COMPONENTS FROM EXHAUST SYSTEM HEAT.
EXPULSION OF FUEL DUE TO OVERPRESSURIZATION. Remedy: MODIFICATION OF THE BASE FUEL VENTING AND EMISSION CONTROL SYSTEM TO REDUCE OPERATING TEMPERATURES AND FUEL SYSTEM PRESSURES.
FUEL LEAK AT THE TOP OF THE FRONT FUEL TANK IN THE AREA OF THE VAPOR VALVE GROMMET. GROMMET MAY SPLIT DUE TO COMPRESSIVE LOAD WHEN INSTALLED IN THE FUEL TANK. Remedy: INSTALLATION OF A NEWLY DESIGNED VAPOR VALVE GROMMET.
THE RUBBER THAT ENCASES BALL STUD AND SOCKET JOINT (CONNECTS STEERING DRAG LINK AND PITMAN ARM) MAY DETERIORATE, CAUSING METAL TO METAL CONTACT, AND MAY EVENTUALLY RESULT IN COMPLETE SEPARATION. CONSEQUENCE OF DEFECT: COMPLETE SEPARATION OF THE DRAG LINK TO PITMAN ARM CONNECTION RESULTS IN LOSS OF STEERING CONTROL WHICH MAY LEAD TO AN ACCIDENT. Remedy: INSTALL NEW DRAG LINK ASSEMBLIES WITH STEEL BALL AND SOCKET JOINTS AT THE PITMAN ARM CONNECTIONS.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
1983-87 E-250 AND 350 WITH 7.5 LITRE AND 1985-87 HEAVY DUTY E-250 AND 350 WITH 5.8 LITRE 4V ENGINE AND A GVW OVER 8,500 LBS. THESE VEHICLES HAVE BEEN DETERMINED TO GENERATE EXCESSIVE UNDERBODY TEMPERATURES AND FUEL SYSTEM PRESSURES IN SEVERE DUTY APPLICATIONS, PARTICULARLY IF FUELED WITH OVERLY VOLATILE GASOLINE. THIS CAN CREATE AN ABNORMAL POTENTIAL FOR EXPULSION OF LIQUID FUEL FROM THE FILLER PIPE UPON REMOVAL OF THE FUEL TANK FILLER CAP. IN THE PRESENCE OF AN IGNITION SOURCE, A VEHICLE FIRE COULD OCCUR. CORRECTION: VEHICLES WILL BE MODIFIED TO MINIMIZE THE POSSIBILITY OF FUEL EXPULSION AND SHIELD UNDERBODY COMPONENTS FROM EXCESSIVE UNDERBODY HEAT. NOTE: E250 AND 350 CLUB WAGONS AND ECONOLINE VANS AND CHASSIS.
UNDER CERTAIN LOW SPEED TIGHT TURNING CONDITIONS UNDER HIGH LOAD, THE RUBBER WITHIN THE RUBBER ENCASED BALL STUD AND SOCKET JOINT CONNECTING THE STEERING DRAG LINK AND PITMAN ARM MAY DETERIORATE CAUSING GALLING OF THE BALL STUD AND SOCKET.THIS COULD EVENTUALLY LEAD TO SEPERATION OF THE DRAG LINK AND PITMAN ARM AND LOSS OF STEERING. CORRECTION:DRAG LINK ASSEMBLIES WITH STEEL BALL AND SOCKET JOINTS WILL BE INSTALLED.
E350 RV AND COMMERCIAL CUTAWAY ECONOLINE VEHICLES. SOME VEHICLES WHERE COMPLETED WITH BODIES WHICH RESTRICTED THE DISSAPATION OF UNDERBODY HEAT.IN SUCH A CASE EXTENDED IDLING COULD OVERHEAT THE COMPOSITE GRAPHITE DRIVESHAFT AND,IF A HIGH START UP TORQUE APPLIED,TWIST AND SHORTEN THE DRIVESHAFT CAUSING THE SLIP YOKE TO DISCONNECT. CORRECTION:METAL DRIVESHAFTS WILL BE INSTALLED.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain