Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1986 Buick Regal, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE. Remedy: HONEYWELL WILL NOTIFY OWNERS AND REPLACE THE FUEL FILTERS FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 18, 2006. OWNERS MAY CONTACT FRAM CUSTOMER SERVICE AT 1-800-890-2075 (OPTION 1).
A SMALL NYLON BUSHING IN THE CRUISE CONTROL SERVO BAIL MAY SLIP OUT OF PLACE, CAUSING INTERMITTENT AND UNEXPECTED INCREASES IN ENGINE SPEED OR DIESELING (ENGINE RUN ON WITH IGNITION OFF). Remedy: INSTALL A NEW BUSHING IN CRUISE CONTROL SERVO BAIL.
UNDER EXTENDED HEADLAMP USAGE, CIRCUITRY IN THE HEADLAMP SWITCH PANEL MIGHT EXPERIENCE INCREASED RESISTANCE AND EXCESSIVE HEAT BUILDUP. Remedy: REPLACE HEADLIGHT SWITCH WITH MODIFIED SWITCH.
SMALL CRACKS MAY DEVELOP IN THE BODY PILLAR AROUND THE DOOR STRIKER BOLT HOLE. Remedy: INSTALL INNER AND OUTER REINFORCEMENT PLATE ON BOTH LEFT AND RIGHT BODY PILLARS.
LEFT HANDED DRIVER'S SIDE SHOULDER BELT ANCHOR PLATE MAY BE UPSIDE DOWN IN LOCK PILLAR SO THAT THE UNTHREADED SLOT OF THE PLATE ALIGNED WITH THE HOLE IN THE LOCK PILLAR. THIS RESULTED IN THE ANCHOR BOLT BEING DRIVEN INTO THE SLOT INSTEAD OF THE THREADED HOLE OF THE ANCHOR PLATE. CONSEQUENCE OF DEFECT: IN A VEHICLE CRASH, BELT ANCHOR BOLT MAY PULL LOOSE FROM ANCHOR PLATE, THUS FAILING TO COMPLY WITH FMVSS 210, SEAT BELT ASSEMBLY ANCHORAGES, AND INCREASES LIKELIHOOD OF INJURY TO OCCUPANT. Remedy: INSTALL A BOLT ANCHOR PLATE REINFORCEMENT AND NEW BOLT, AS NECESSARY.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
A SMALL NYLON BUSHING IN THE CRUISE CONTROL SERVO BAIL (BRACKET) MAY SLIP OUT OF PLACE RESULTING IN POSSIBLE INTERMITTENT INCREASES IN ENGINE SPEED OR DIESELING. THIS CONDITION COULD ALSO CAUSE THE SERVO ROD ASSEMBLY TO WEAR THROUGH THE BALL AND CATCH ON OTHER COMPONENTS POSSIBLY RESULTING IN A STUCK THROTTLE. THIS COULD RESULT IN LOSS OF VEHICLE CONTROL AND A POSSIBLE CRASH. CORRECTION: A BUSHING KIT WILL BE INSTALLED ON THE CRUISE CONTROL SERVO BAIL.
Certain vehicles equipped with hatchroof option may not comply with CMVSS 210 - Seatbelt Assembly Anchorages. Drivers side shoulder belt anchor plate may be located upside down which can result in the anchor bolt pulling loose in an accident.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain