Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1988 Honda Prelude, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
THE ACCELERATOR PEDAL STOPPER MAY BE BENT WHEN EXCESSIVE DOWNWARD FORCE IS APPLIED AFTER PEDAL HAS CONTACTED THE STOPPER. Remedy: INSTALL A SUPPORT TO PREVENT STOPPER FROM BENDING.
THE REAR INBOARD SEAT ANCHORAGE BRACKET FOR THE FRONT SEATS MAY NOT WITHSTAND THE FORCE REQUIRED BY FMVSS 207. Remedy: INSTALL A REINFORCING PLATE TO REAR INBOARD SEAT ANCHORAGE BRACKET FOR EACH FRONT SEAT.
THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY. Remedy: OWNERS SHOULD PROMPTLY CHECK THE CONDITION AND OPERATION OF BOTH FRONT SAFETY BELT BUCKLES. CAREFULLY INSPECT THE RED RELEASE BUTTON FOR ANY BREAKS OR CRACKS. CHECK THAT BOTH BUCKLES ARE OPERATING PROPERLY BY INSERTING EACH LATCH PLATE INTO ITS BUCKLE, TUG ON THE BELT TO MAKE SURE THE LATCH IS SECURELY LOCKED, THEN PRESS THE RELEASE BUTTON. THE LATCH PLATE SHOULD POP OUT OF THE BUCKLE WHEN THE BUTTON IS PRESSED. IF EITHER RELEASE BUTTON SHOWS ANY SIGN OF BREAKAGE OR CRACKING, OR IF EITHER BUCKLE FAILS TO OPERATE PROPERLY, PROMPTLY CONTACT YOUR AUTHORIZED HONDA/ACURA DEALER TO SCHEDULE AN APPOINTMENT TO HAVE THE BUCKLE REPLACED OR REPAIRED, FREE OF CHARGE. THE MANUFACTURER IS DEVELOPING A REMEDY DESIGNED TO PREVENT THE FAILURE OF THE BUTTONS THAT ARE NOT CURRENTLY BROKEN.
VIBRATION AND HIGH UNDERHOOD TEMPERATURES COULD CAUSE POWER STEERING SUPPLY HOSE AT THE CONNECTOR CLAMP SEAL TO DEVELOP A FLUID LEAK. Remedy: INSTALL AN IMPROVED POWER STEERING SUPPLY HOSE ASSEMBLY.
A SMALL AMOUNT OF COOLANT SEEPAGE MAY OCCUR, AND EVENTUALLY RESIDUE MAY ACCUMULATE ON THE THROTTLE VALVE. Remedy: REPLACE THROTTLE BODY ASSEMBLY.
OWNERS MANUAL INFORMATION REQUIRED BY FMVSS 210, SECTIONS 6A AND 6B WAS OMITTED FROM THE MANUAL. Remedy: UPGRADE EXISTING MANUALS BY INSERTING ADHESIVE BACKED CORRECTION PAGES.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain vehicles, the platic front seatbelt release buttons may break allowing plastic pieces to fall into the buckle assembly. If this should happen, a no latch, false latch or failure to unlatch condition could occur creating the risk of personal injury in the event of a crash or sudden stop. Correction: Front seatbelt buckles will be repaired or replaced as necessary.
On certain vehicles, the accelerator pedal stopper may be bent when excessive downward force is applied after the pedal has contacted the stopper. In the worst case, the edge of the pedal can be caught and held down by the bent stopper. This could result in loss of vehicle control and a crash without prior warning. Correction: A support will be installed to prevent the stopper from bending.
On certain vehicles, the power steering supply hose at the connector clamp seal could develop a small leak. If the fluid were to contact the exhaust manifold a fire could result. Correction: A reinforced rubber power steering hose assembly will be installed.
On certain Prelude SI vehicles, throttle body castings may contain slight porosity. During vehicle usage, coolant seepage may occur and eventually residue may accumulate on the throttle valve. The residue could cause the throttle valve to return slowly from the slightly open position to the idle position when the accelerator pedal is released. Correction: The throttle body assembly will be replaced.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain