Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1990 Pontiac Grand Prix, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE. Remedy: HONEYWELL WILL NOTIFY OWNERS AND REPLACE THE FUEL FILTERS FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 18, 2006. OWNERS MAY CONTACT FRAM CUSTOMER SERVICE AT 1-800-890-2075 (OPTION 1).
VEHICLE DESCRIPTION: PASSENGER VEHICLES ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, WISCONSIN, AND THE DISTRICT OF COLUMBIA, WHERE ROAD SALT USE IS HEAVY. A CONDITION WHERE ONE OR BOTH FRONT ENGINE CRADLE BOLTS CAN PULL THROUGH THE RETAINERS DUE TO CORROSION OF THE RETAINERS. Remedy: DEALERS WILL REPLACE THE FRONT AND REAR FRAME/CRADLE BOLTS AND RETAINERS.
FRONT SHOULDER SAFETY BELT WEBBING MAY SEPARATE AT FRONT BELT UPPER GUIDE LOOPS ON EITHER SIDE OF THE FRONT SEAT. Remedy: INSTALL A CONTROLLED ROTATION BRACKET ON DRIVER AND PASSENGER SIDE FRONT SEAT BELT GUIDE LOOPS.
CRACKS DEVELOP IN THE WHEEL MOUNTING SURFACE. IF THESE CRACKS BECOME SEVERE ENOUGH, THE WHEEL WILL COMPLETELY SEPARATE FROM THE VEHICLE. Remedy: DEALERS WILL INSPECT THE MANUFACTURING DATE CODES STAMPED ON EACH WHEEL OF THE VEHICLE AND IF A WHEEL FALLS WITHIN THE SPECIFIED DATE CODE RANGE, THE DEALER WILL REPLACE THAT WHEEL ASSEMBLY.
CRACKS DEVELOP IN THE WHEEL MOUNTING SURFACE. IF THESE CRACKS BECOME SEVERE ENOUGH, THE WHEEL WILL COMPLETELY SEPARATE FROM THE VEHICLE. Remedy: DEALERS WILL INSPECT THE MANUFACTURING CODES STAMPED ON EACH WHEEL OF THE VEHICLE AND IF A WHEEL FALLS WITHIN THE SPECIFIED DATE CODE RANGE, THE DEALER WILL REPLACE THAT WHEEL ASSEMBLY.
VEHICLE DESCRIPTION: PASSENGER VEHICLES AND MINI VANS ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE FOLLOWING STATES: CONNECTICUT, ILLINOIS, INDIANA, MAINE, MASSACHUSETTS, MICHIGAN, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT AND WISCONSIN. THE REAR CRADLE BOLTS PULL THROUGH THE RETAINERS DUE TO CORROSION OF THE RETAINER. IF BOTH BOLTS PULL THROUGH, THE REAR CRADLE WOULD NOT LONGER BE SUPPORTED AT THESE MOUNTING LOCATIONS AND THE STEERING INTERMEDIATE SHAFT CAN SEPARATE FROM THE STEERING GEAR. Remedy: DEALERS WILL REPLACE THE REAR CRADLE BOLTS AND RETAINERS.
FRONT SHOULDER BELT GUIDE LOOP ATTACHMENT FASTENER MAY PULL THROUGH DOOR MOUNTED ANCHOR PLATE. Remedy: REPLACE FRONT SHOULDER BELT GUIDE LOOP ATTACHMENT NUTS AND INSTALL NEW GUIDE COVER.
DURING A REAR END COLLISION, THE REAR EXHAUST SYSTEM HEAT SHIELD, WHICH IS WELDED TO THE TAIL PIPE ASSEMBLY, MAY PUNCTURE THE FUEL TANK. Remedy: REMOVE REAR EXHAUST SYSTEM HEAT SHIELD FROM THE PIPE ASSEMBLY.
BRAKE STOPLAMPS MAY NOT ILLUMINATE OR, IN SOME CASES, STOPLAMPS WILL NOT STAY ILLUMINATED ALL THE TIME WHEN BRAKES ARE APPLIED DUE TO A FAULTY STOPLAMP SWITCH. ALSO IN VEHICLES EQUIPPED WITH CRUISE CONTROL, A FAULTY STOPLAMP SWITCH CAN RESULT IN RESUMPTION OF THE CRUISE CONTROL FUNCTION UPON RELEASE OF THE BRAKE PEDAL. Remedy: INSTALL AN IMPROVED DESIGN STOPLAMP SWITCH.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Vehicles located in the high corrosion provinces east of the Manitoba/Ontario border. Certain vehicles may exhibit a condition in which the frame/cradle retainer bolts pull through the retainers due to corrosion of the retainer. If both front bolts or both rear bolts pull through, the frame/cradle would not be properly supported and the intermediate steering shaft may separate from the steering gear. If this were to occur while the vehicle was in motion, a vehicle crash could result without prior warning. Correction: Dealers will replace the front and rear frame/cradle bolts and retainers. Note: This recall superceedes TC recall 1995-010.
On certain vehicles located in New Brunswick, Nova Scotia, Newfoundland and Prince Edward Island, extreme levels of moisture and salt can result in corrosion at or near the engine cradle mounts resulting in possible failure of the mounts. If failures occur at both rear mounts or both front mounts, movement of the cradle can cause separation of the steering intermediate shaft resulting in loss of steering control. Correction: Dealers will install reinforcement plates on repairable cradles, non repairable cradles will be replaced.
On certain vehicles, cracks may develop in the wheel mounting surface, and, should the cracks become severe enough, the wheel could completely separate from the vehicle. This could adversely affect steering and braking control and result in a crash without prior warning. Correction: Vehicles will be inspected and wheels falling within a specified date code range will be replaced.
On certain vehicles, the rear engine cradle bolts may pull through due to corrosion of the retainers. If this should occur, the cradle would no longer be supported at these mounting locations and the steering shaft may separate from the steering gear. This could result in loss of steering control. Correction: Rear cradle bolts and retainers will be replaced.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Crash-test ratings from NHTSA's New Car Assessment Program.
Source: NHTSA (US Department of Transportation) · US public domain
On certain vehicles, the steel wheels may develop cracks in the wheel mounting surface and, should the cracks become severe enough, the wheel could completely separate from the vehicle. This could adversely affect steering and braking control and result in a vehicle crash. Correction: Wheels will be inspected and replaced if required.
Certain vehicles may not comply with CMVSS 1103 - Exhaust Emissions. Cracks may develop in the casing of the integrated direct ignition coil. Correction: Ignition coils will be inspected and replaced if necessary.
On certain vehicles, the front shoulder seat belt webbing may separate at the seat belt upper guide loops (driver and/or passenger side). Separation of the webbing would occur without prior warning and could increase the risk of injury to belted front outboard occupants in the event of a crash. Correction: Dealers will install a controlled rotation bracket on both the driver and passenger side front seat shoulder belt guide loops to prevent this condition from occuring.
THE BRAKE STOPLAMP SWITCH CONTACTS MAY EITHER NOT CLOSE OR NOT OPEN RESULTING IN TWO POSSIBLE SETS OF CONDITIONS. FIRST, IF THE SWITCH CONTACTS WILL NOT CLOSE, THE BRAKE STOPLAMPS WILL NOT ILLUMINATE AND THE CRUISE CONTROL WILL NOT ENGAGE. SECOND, IF THE SWITCH CONTACTS WILL NOT OPEN, THE CONTROL WILL DISENGAGE DURING BRAKE PEDAL APPLICATION BUT WILL RE-ENGAGE WHEN THE BRAKE PEDAL IS RELEASED. (NOTE: THE CRUISE CONTROL WILL REMAIN DISENGAGED IF THE VEHICLE IS SLOWED BELOW 19-23 KILOMETRES. THE DRIVER MAY ALSO DISENGAGE THE CRUISE CONTROL MANUALLY AT THE CRUISE CONTROL SWITCH). CORRECTION: AN IMPROVED STOPLAMP SWITCH WILL BE INSTALLED ON AFFECTED VEHICLES.
Certain vehicles do not comply with CMVSS 210 - Seatbelt Assembly Anchorages. Anchor bolt may pull through the upper anchorage plate. Correction: Nut assembly with a larger diameter flanged nut will be installed in place of the existing nut assembly.