Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1991 Buick Regal, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE. Remedy: HONEYWELL WILL NOTIFY OWNERS AND REPLACE THE FUEL FILTERS FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 18, 2006. OWNERS MAY CONTACT FRAM CUSTOMER SERVICE AT 1-800-890-2075 (OPTION 1).
VEHICLE DESCRIPTION: PASSENGER VEHICLES ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, WISCONSIN, AND THE DISTRICT OF COLUMBIA, WHERE ROAD SALT USE IS HEAVY. A CONDITION WHERE ONE OR BOTH FRONT ENGINE CRADLE BOLTS CAN PULL THROUGH THE RETAINERS DUE TO CORROSION OF THE RETAINERS. Remedy: DEALERS WILL REPLACE THE FRONT AND REAR FRAME/CRADLE BOLTS AND RETAINERS.
FRONT SHOULDER SAFETY BELT WEBBING MAY SEPARATE AT FRONT BELT UPPER GUIDE LOOPS ON EITHER SIDE OF THE FRONT SEAT. Remedy: INSTALL A CONTROLLED ROTATION BRACKET ON DRIVER AND PASSENGER SIDE FRONT SEAT BELT GUIDE LOOPS.
INCORRECT CLEAR FRONT SIDE MARKER BULBS WERE INSTALLED RATHER THAN AMBER BULBS. THIS DOES NOT CONFORM TO THE REQUIREMENTS OF FMVSS NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." Remedy: DEALERS WILL REPLACE THE CLEAR BULBS WITH THE CORRECT AMBER BULBS.
THE FUEL FEED HOSE CAN PULL OUT OF THE CRIMPED COUPLING AT THE ENGINE END OF THE HOSE ASSEMBLY, CAUSING FUEL LEAKAGE. Remedy: INSTALL A NEW FUEL FEED HOSE.
THE FRONT DOOR SHOULDER BELT GUIDE LOOPS MAY BE CRACKED AND ARE NOT IN COMPLIANCE WITH FMVSS 208. Remedy: INSTALL REINFORCING PLATES ON THE CRACKED SHOULDER BELT GUIDES.
VEHICLE DESCRIPTION: PASSENGER VEHICLES AND MINI VANS ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE FOLLOWING STATES: CONNECTICUT, ILLINOIS, INDIANA, MAINE, MASSACHUSETTS, MICHIGAN, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT AND WISCONSIN. THE REAR CRADLE BOLTS PULL THROUGH THE RETAINERS DUE TO CORROSION OF THE RETAINER. IF BOTH BOLTS PULL THROUGH, THE REAR CRADLE WOULD NOT LONGER BE SUPPORTED AT THESE MOUNTING LOCATIONS AND THE STEERING INTERMEDIATE SHAFT CAN SEPARATE FROM THE STEERING GEAR. Remedy: DEALERS WILL REPLACE THE REAR CRADLE BOLTS AND RETAINERS.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Vehicles located in the high corrosion provinces east of the Manitoba/Ontario border. Certain vehicles may exhibit a condition in which the frame/cradle retainer bolts pull through the retainers due to corrosion of the retainer. If both front bolts or both rear bolts pull through, the frame/cradle would not be properly supported and the intermediate steering shaft may separate from the steering gear. If this were to occur while the vehicle was in motion, a vehicle crash could result without prior warning. Correction: Dealers will replace the front and rear frame/cradle bolts and retainers. Note: This recall superceedes TC recall 1995-010.
On certain vehicles located in New Brunswick, Nova Scotia, Newfoundland and Prince Edward Island, extreme levels of moisture and salt can result in corrosion at or near the engine cradle mounts resulting in possible failure of the mounts. If failures occur at both rear mounts or both front mounts, movement of the cradle can cause separation of the steering intermediate shaft resulting in loss of steering control. Correction: Dealers will install reinforcement plates on repairable cradles, non repairable cradles will be replaced.
On certain vehicles, the rear engine cradle bolts may pull through due to corrosion of the retainers. If this should occur, the cradle would no longer be supported at these mounting locations and the steering shaft may separate from the steering gear. This could result in loss of steering control. Correction: Rear cradle bolts and retainers will be replaced.
VEHICLES WITH 3800 ENGINES MAY HAVE FUEL FEED HOSES WHICH MAY PULL OUT OF THE CRIMPED COUPLING AT THE ENGINE END OF THE HOSE ASSEMBLY. IF THIS COUPLING WERE TO SEPARATE, FUEL COULD SPILL ONTO HOT ENGINE COMPONENTS AND POSSIBLY CAUSE AN ENGINE COMPARTMENT FIRE. CORRECTION: A NEW FUEL FEED HOSE WILL BE INSTALLED ON AFFECTED VEHICLES.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Crash-test ratings from NHTSA's New Car Assessment Program.
Source: NHTSA (US Department of Transportation) · US public domain
Certain vehicles do not comply with CMVSS 208 - Seatbelt Installations. Front door shoulder belt guide loops may not provide front seat occupants with proper protection in the event of a crash. Correction: Dealers will inspect the front door shoulder belt guide loops for possible cracks. If a cracked guide loop is found, both front door guide loops will have reinforcing plates installed.
On certain vehicles, the front shoulder seat belt webbing may separate at the seat belt upper guide loops (driver and/or passenger side). Separation of the webbing would occur without prior warning and could increase the risk of injury to belted front outboard occupants in the event of a crash. Correction: Dealers will install a controlled rotation bracket on both the driver and passenger side front seat shoulder belt guide loops to prevent this condition from occuring.