Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1991 Mercury Tracer, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
THE ROLL PINS SECURING THE IGNITION LOCK IN THE STEERING COLUMN HOUSING CAN SEPARATE OR MOVE OUT OF POSITION. Remedy: IF ONE OR BOTH OF THE ROLL PINS ARE MISSING OR NOT FULLY INSERTED, THE IGNITION LOCK HOUSING WILL BE REPLACED, ALONG WITH THE DOOR-LOCKS AND THE LIFTGATE OR DECK-LID LOCKS SO THAT KEY COMPATIBILITY IS MAINTAINED. IF BOTH PINS ARE PRESENT AND FULLY INSERTED, A PLASTIC SNAP-ON SLEEVE WILL BE INSTALLED AS A PRECAUTION TO PREVENT THE ROLL PINS FROM COMING OUT.
THE OFFSET TOE ADJUSTING PIN CAN FRACTURE UNDER CONDITIONS SUCH AS TORSIONAL LOADS, FLEXING MOTION, IMPACT LOADS, AND OVERTORQUING. Remedy: DANA WILL PAY FOR REPLACEMENT AND LABOR COSTS OF THE ADJUSTMENT PIN WITHOUT CHARGE TO THE INSTALLING FACILITY AND THE VEHICLE OWNER. THESE PINS SHOULD BE REPLACED BY A FORD ORIGINAL EQUIPMENT PIN ASSEMBLY. OWNER OR INSTALLER INQUIRIES CONCERNING THIS RECALL CAMPAIGN SHOULD CONTACT DANA SERVICE CENTER AT 1-800-248-9606.
FATIGUE CRACKS CAN DEVELOP IN THE SOLDER JOINT BETWEEN THE FUEL RETURN TUBE AND THE FUEL PUMP SENDING UNIT LOCATED AT THE TOP OF THE FUEL TANK. Remedy: INSTALL A NEW FUEL PUMP SENDING ASSEMBLY.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
NOTE: VEHICLES LOCATED IN ONTARIO, QUEBEC AND THE ATLANTIC PROVINCES. THE FUEL PUMP WIRING ASSEMBLY MAY CORRODE DUE TO ROAD SALT, POSSIBLY RESULTING IN AN ELECTRICAL BRIDGE DEVELOPING BETWEEN THE FUEL PUMP ELECTRICAL CIRCUIT AND THE FUEL GAUGE SENDER TERMINALS. THIS COULD CAUSE THE FUEL SENDER GROUND CIRCUIT TO OVERHEAT THE WIRING AND MELT ITS INSULATION PRIOR TO THE OPENING OF THE FUSE IN THE FUEL PUMP POWER CIRCUIT. THIS WOULD CAUSE SMOKE AND ODOUR AND COULD RESULT IN LOSS OF FUEL DELIVERY TO THE ENGINE AND THE ENGINE STOPPING. CORRECTION: A FUSED JUMPER HARNESS WILL BE INSTALLED IN THE FUEL PUMP/SENDER ELECTRICAL CIRCUIT.
ON VEHICLES WITH MANUAL TRANSMISSION, THE ROLL PINS SECURING THE IGNITION LOCK CYLINDER IN THE STEERING COLUMN HOUSING MAY NOT REMAIN IN PLACE. THIS COULD CAUSE THE IGNITION LOCK CYLINDER TO DISENGAGE FROM THE STEERING COLUMN HOUSING WHICH COULD RESULT IN STEERING COLUMN LOCK-UP AND LOSS OF STEERING CONTROL. CORRECTION: VEHICLES WILL BE INSPECTED AND IF ROLL PINS ARE PRESENT AND FULLY INSERTED, A PLASTIC SNAP-ON SLEEVE WILL BE INSTALLED TO PREVENT THE PINS FROM COMING OUT. IF ONE OR BOTH OR THE ROLL PINS ARE MISSING OR NOT FULLY INSERTED, THE IGNITION LOCK HOUSING ASSEMBLY WILL BE REPLACED (ALONG WITH THE DOOR LOCKS AND THE LIFTGATE/DECK-LID LOCKS SO THAT KEY COMPATIBILITY IS MAINTAINED).
FATIGUE CRACKS MAY DEVELOP IN THE SOLDER JOINT BETWEEN THE FUEL RETURN TUBE AND THE FUEL PUMP SENDING UNIT LOCATED ON THE TOP OF THE FUEL TANK. THIS WOULD ALLOW FUEL VAPOURS TO ESCAPE FROM THE TANK AND WHEN THE TANK IS 7/8 OR MORE FULL, A SMALL AMOUNT OF LIQUID FUEL MAY LEAK FROM THE CRACK PRESENTING A POTENTIAL FIRE HAZARD. NOTE: FOR ESCORT MODELS ONLY GT AND LXE LINES INVOLVED. CORRECTION: VEHICLES WILL BE INSPECTED AND FUEL PUMP SENDING UNIT ASSEMBLY WILL BE REPLACED WITH ONE OF IMPROVED STRENGTH.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain