Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1991 Plymouth Grand Voyager, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
VEHICLE DESCRIPTION: MINI VANS. THE BOLTS USED TO ATTACH THE STRUT TO THE BODY AND THE REAR LIFTGATE CAN ACCUMULATE FATIGUE DAMAGE IF THREE FACTORS COMBINE. IF THE BOLT IS LOOSE, THE GAS STRUT IS OVER-PRESSURIZED, AND THE FREQUENCY OF OPENING AND CLOSING CYCLES IS HIGHER THAN FOR THE AVERAGE CUSTOMER, THE BOLT CAN FAIL. Remedy: DEALERS WILL INSPECT FOR LOOSE FASTENERS, IF THE FASTENERS ARE LOOSE, THE STRUT (AND INTEGRAL BOLTS) WILL BE REPLACED. IF THE BOLT SHOWS EVIDENCE OF TORQUE, THE BOLT WILL BE REMOVED, LARGER WASHERS WILL REPLACE THE EXISTING WASHER AND THE BOLT WILL BE REINSTALLED AND HAND TIGHTENED TO THE TARGET TORQUED.
VEHICLE DESCRIPTION: PASSENGER MINI-VANS. THE CENTER REAR SEAT, RIGHT OUTBOARD SIDE, SAFETY BELT ANCHOR HOOK CAN BECOME UNATTACHED FROM THE BODY ANCHOR POSITION. Remedy: DEALERS WILL REPLACE THE ANCHOR HOOK RETAINING CLIP WITH A REVISED PROFILE CLIP AND A COVER PLATE.
VEHICLE DESCRIPTION: PASSENGER MINI-VANS. COVERS ON THE SOLID STALK MOUNTED SEAT BELT BUCKLES CAN BECOME DISLODGED CAUSING THE RELEASE BUTTON TO STICK INSIDE THE COVER. THE BUCKLE WOULD THEN BE ONLY PARTIALLY LATCHED. Remedy: DEALERS WILL INSTALL A COVER RETAINING CLIP TO THE STALK MOUNTED BUCKLE COVER TO PREVENT DISLOCATION OF THE BUCKLE COVER.
THE ABS HYDRAULIC CONTROL UNIT CAN EXPERIENCE EXCESSIVE BRAKE ACTUATOR PISTON SEAL WEAR CAUSING PUMP-MOTOR DETERIORATION. Remedy: DEALERS WILL TEST THE VEHICLE'S ANTI-LOCK BRAKE SYSTEM AND REPAIR THE VEHICLES IF NECESSARY. ALSO THE WARRANTY ON ALL ABS COMPONENTS WILL BE EXTENDED TO 10 YEARS OR 100,000 MILES (EXCEPT FOR THE BRAKE ACTUATOR PISTON ASSEMBLY AND THE PUMP-MOTOR ASSEMBLY WHICH WILL HAVE A LIFETIME COVERAGE). OWNERS WILL ALSO BE REIMBURSED FOR PREVIOUS ABS COMPONENT REPAIR COSTS.
VEHICLE DESCRIPTION: MINIVANS. THE LEFT HAND WINDSHIELD WIPER PIVOT DRIVE ARM WAS NOT MECHANICALLY STAKED TO THE PIVOT SHAFT. Remedy: DEALERS WILL REPLACE THE LEFT HAND SIDE WINDSHIELD WIPER PIVOT ASSEMBLY.
THE STEERING WHEEL ARMATURE STAMPING CAN CRACK AND SEPARATE FROM THE CENTER HUB ATTACHMENT TO THE STEERING COLUMN. Remedy: DEALERS WILL INSPECT THE STEERING WHEEL FOR ARMATURE CRACKS IN THE CENTER HUB ATTACHMENT AREA. ANY STEERING WHEELS SHOWING CRACKS WILL BE REPLACED. ALL OTHER VEHICLES WILL HAVE A REINFORCEMENT PLATE INSTALLED TO PREVENT STEERING WHEEL SEPARATION IN THE EVENT CRACKING OCCURS.
VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER MINIVANS WITH REMOTE RELEASE. THIS IS NOT A SAFETY RECALL. THERE HAS BEEN NO DETERMINATION THAT A SAFETY DEFECT EXISTS WITH THE MINIVAN LATCHES. CHRYSLER IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE LIFTGATE LATCH ASSEMBLY OF THE AFFECTED MINIVANS. IN A COLLISION, THE REAR LIFTGATE LATCH ASSEMBLY COULD OPEN. Remedy: CHRYSLER DEALERS WILL REPLACE THE LIFTGATE LATCH WITH A NEW STRONGER LATCH ASSEMBLY WITHOUT CHARGE. CHRYSLER BEGAN NOTIFYING OWNERS OF THESE VEHICLES IN MARCH 1996.
VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER MINIVANS WITHOUT REMOTE RELEASE. THIS IS NOT A SAFETY RECALL. THERE HAS BEEN NO DETERMINATION THAT A SAFETY DEFECT EXISTS WITH THE MINIVAN LATCHES. CHRYSLER IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE LIFTGATE LATCH ASSEMBLY OF THE AFFECTED MINIVANS. IN A COLLISION, THE REAR LIFTGATE LATCH ASSEMBLY COULD OPEN. Remedy: CHRYSLER DEALERS WILL REPLACE THE LIFTGATE LATCH WITH A NEW STRONGER LATCH ASSEMBLY WITHOUT CHARGE. CHRYSLER BEGAN NOTIFYING OWNERS OF THESE VEHICLES IN OCTOBER 1995.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain vehicles, the left hand windshield wiper pivot drive arm was not mechanically staked to the pivot shaft. This may allow the drive arm to disengage from the shaft and lead to a loss of wiper function. Correction: The left windshield wiper pivot assembly will be replaced with one that incorporates an improved mechanical connection of the drive link to the pivot shaft.
The first row rear seat outboard side seat belt anchor hook can become unattached from the body anchor position. Also, the covers on solid stalk mounted seat belt buckles may become dislodged. Should a cover become dislodged, the release button may stick inside the cover creating the potential for the buckle to become partially latched. In the event of a vehicle crash, either of these conditions could result in the occupant not being properly restrained. Correction: Anchor hook retaining clip will be replace with a revised profile clip and cover plate. Dealers will also install a cover retaining clip to the stalk mounted buckle cover to prevent dislocation of the buckle cover.
A combination of no bolt torque, high pressure in the strut and a severe duty cycle can create the potential for the liftgate strut attaching bolts to separate. This could result in injury to persons standing under the liftgate at the time of failure. Correction: Liftgate struts will be inspected for loose fasteners. If fasteners are loose, the strut (and integral bolts) will be replaced. If the bolt shows evidence of torque, the bolt will be removed, large washers will be installed and bolt will be torqued to specification.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
The steering wheel armature stamping may crack and separate from the centre hub of the steering column. This could adversely affect steering control and result in a possible crash without prior warning. Correction: Steering wheels exhibiting cracks will be replaced. All other involved vehicles will have a anti-separation plate installed to prevent separation of the steering wheel from the steering column.
Note: Vehicles equipped with Bendix-10 Antilock Brake System (ABS) Vehicles with ABS brakes may experience premature actuator piston seal wear in the ABS hydraulic control unit and/or actuator pump motor deterioration. If this occurs, the ABS function may be lost and reduced power assist may be experienced during vehicle braking. Correction: Vehicles with ABS malfunction will be repaired as necessary. Warranty on all ABS components will be extended to 10 years or 160,000 km (except for the brake actuator piston assembly and the pump-motor assembly which will have lifetime coverage).
On certain vehicles equipped with an anti-lock brake system (ABS), the high pressure hose may leak or detach due to inadequate crimping of the hose-to-end fittings. This condition could result in loss of brake power assist and a possible increase in stopping distances. Correction:(526) ABS high pressure hose will be replaced with a hose of different design and construction. (527) four hundred and twenty six of the identified mini vans will also have the ABS pump casting inspected for porosity. Leaking pumps, if found, will be replaced.