Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1991 Volkswagen Jetta, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS. Remedy: SABERSPORT WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON MAY 11, 2009. OWNERS MAY CONTACT SABERSPORT AT 1-909-598-7589.
CERTAIN HYDRAULIC BRAKE HOSES, P/N 171.611.107B, SOLD AS REPLACEMENT EQUIPMENT FOR 1975-1985 VOLKSWAGEN (VW) RABBIT; 1985-1992 VW GOLF; AND 1980-1992 VW JETTA PASSENGER VEHICLES. POSSIBLE BRAKE HOSE RUPTURE COULD OCCUR WHICH FAILS TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 106, "BRAKE HOSES." Remedy: FOREIGN PARTS DISTRIBUTORS WILL NOTIFY OWNERS AND REPLACE THE BRAKE HOSES WITH COMPLIANT BRAKE HOSES. THE RECALL BEGAN ON MARCH 30, 2006. OWNERS MAY CONTACT FOREIGN PARTS DISTRIBUTORS AT 305-885-8646 EXT. 11.
THE LOCK NUT OF THE CRUISE CONTROL ROD FOR THE OPERATING SERVO MAY NOT HAVE BEEN PROPERLY TORQUED DURING MANUFACTURE. Remedy: CHECK AND ASSURE PROPER LOCK NUT TORQUE ON THE CRUISE CONTROL ROD.
THE FUEL HOSE ATTACHED TO THE FUEL DISTRIBUTION RAIL ON THE ENGINE MAY SHRINK BEYOND THE CLAMP FORCE OF THE FUEL HOSE CLAMPS, ALLOWING FUEL TO LEAK. Remedy: REPLACE THE FUEL HOSE ATTACHED TO THE FUEL RAIL AND INSTALL A NEW SPRING TYPE SELF-TIGHTENING CLAMP.
AN ENGINE PREHEATING TUBE MAY NOT BE PROPERLY SUPPORTED DUE TO A MISSING SUPPORT BRACKET, CAUSING THE PREHEATING TUBE TO CHAFE AGAINST THE RIGHT FRONT METAL BRAKE LINE. THIS CAN DAMAGE THE HYDRAULIC LINE, CAUSING BRAKE FLUID LEAKAGE AND DIMINISHED BRAKING IN ONE BRAKE CIRCUIT. Remedy: DEALERS WILL INSTALL A PREHEATING TUBE SUPPORT BRACKET TO ENSURE PROPER POSITIONING RELATIVE TO THE RIGHT FRONT METAL BRAKE LINE.
THE VENTURI TUBE LOCATED IN THE THROTTLE VALVE HOUSING CAN BECOME LOOSE AND FALL AGAINST THE THROTTLE PLATE. Remedy: REPLACE THE PRESS-FIT VENTURI TUBE WITH A THREAD TYPE TUBE.
FRONT BRAKE HOSES OF INSUFFICIENT LENGTH WERE INSTALLED IN SOME VEHICLES. THESE SHORT HOSES COULD STRETCH AND DEVELOP CRACKS. Remedy: REPLACE BOTH BRAKE HOSES.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
NOTE: GASOLINE POWERED FUEL INJECTED VEHICLES. DURING WINTER PERIODS OF LOW TEMPERATURE WITH HIGH HUMIDITY, THE AIR PRE-HEATING SYSTEM MAY NOT BE SUFFICIENT TO PREVENT THROTTLE ICING DURING LONG DISTANCE DRIVING DUE TO PRE-HEATER VACUUM SWITCH CONTAMINATION. THIS COULD PREVENT THE THROTTLE FROM RETURNING TO THE IDLE POSITION WHEN THE ACCELERATOR PEDAL IS RELEASED. CORRECTION: A DE-ICING KIT WILL BE INSTALLED IN AFFECTED VEHICLES.
FUEL LEAKAGE MAY OCCUR AT THE FUEL HOSE TO FUEL RAIL CONNECTION. ESCAPING FUEL COULD COME INTO CONTACT WITH HOT ENGINE COMPONENTS AND POSSIBLY CAUSE AN ENGINE COMPARTMENT FIRE. CORRECTION: FUEL HOSE WHICH ATTACHES TO THE FUEL RAIL WILL BE REPLACED AND NEW SPRING TYPE HOSE CLAMPS WILL BE INSTALLED.
CORROSION DUE TO ROAD SALT MAY PREVENT THE HOOD LATCH AND THE SAFETY CATCH FROM WORKING PROPERLY. THIS COULD RESULT IN HOOD FLY-UP WHILE THE VEHICLE IS IN MOTION RESULTING IN OBSCURED DRIVER VISION AND A POSSIBLE CRASH. CORRECTION: OWNERS OF AFFECTED VEHICLES WILL BE ADVISED BY MAIL REGARDING THE NECESSITY FOR PERIODIC LUBRICATION OF THE ENGINE HOOD LATCH MECHANISM. DEALERS WILL BE ADVISED TO LUBRICATE THE ENGINE HOOD MECHANISM WHENEVER AN AFFECTED VEHICLE IS BEING SERVICED.
IF THE ENGINE OVERHEATS, IT IS POSSIBLE THAT THE WALL OF THE END CAP CONNECTING THE HEAT EXCHANGER'S CORE TO THE ENGINE COOLING SYSTEM COULD RUPTURE AND ALLOW HOT COOLANT TO ESCAPE. SHOULD THIS HAPPEN, SOME OF THE COOLANT COULD CONTACT THE DRIVER'S FEET, CAUSING INJURY AND STEAM UP THE INTERIOR OF THE VEHICLE, IMPAIRING VISIBILITY. CORRECTION: HEAT EXCHANGER WILL BE REPLACED.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
THESE VEHICLES DO NOT COMPLY WITH CMVSS 215 - BUMPERS. TURN SIGNAL LAMP CRACKED IN IMPACT TEST.
DEFECTIVE ENGINE SUB-FRAME BOLTS COULD SHEAR OFF AND ALLOW THE FRONT WHEEL CONTROL ARM TO PIVOT THEREBY PLACING THE CORRESPONDING WHEEL OUT OF ALIGNMENT. THIS COULD CAUSE OR CONTRIBUTE TO A VEHICLE CRASH. CORRECTION: DEFECTIVE BOLTS WILL BE REPLACED ON AFFECTED VEHICLES.