Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1992 Ford Crown Victoria, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
FORD IS RECALLING 225,000 MY 1992-2003 ECONOLINE, MY 1993-1995 TAURUS SHO, MY 1992-1998 CROWN VICTORIA, MY 1993 BRONCO, F-SERIES, MY 1995-1997 F-SERIES SUPER DUTY STRIPPED CHASSIS, MY 1992-1998 MERCURY GRAND MARQUIS, AND MY 1992-1995 LINCOLN TOWN CAR VEHICLES. THE AFFECTED VEHICLES WERE PREVIOUSLY REPAIRED USING A WIRING HARNESS THAT IS NOT COMPATIBLE WITH THE VEHICLE CIRCUIT POLARITY. Remedy: DEALERS WILL INSTALL A NEW WIRING HARNESS, OR REPLACE THE MATING ELECTRICAL COMPONENT. THE RECALL BEGAN ON FEBRUARY 18, 2008. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
ON CERTAIN PICKUP TRUCKS, PASSENGER VEHICLES, SPORT UTILITY VEHICLES, AND MOTOR HOMES CHASSIS, THE SPEED CONTROL DEACTIVATION SWITCH MAY, UNDER CERTAIN CONDITIONS, LEAK INTERNALLY AND THEN OVERHEAT, SMOKE, OR BURN. Remedy: DEALERS WILL INSTALL A FUSED WIRING HARNESS. OWNERS OF THE PASSENGER CARS INCLUDED IN THIS CAMPAIGN WILL BE INSTRUCTED TO RETURN THEIR VEHICLES TO THEIR DEALERS TO HAVE THE SPEED CONTROL DEACTIVATION SWITCH DISCONNECTED AS AN INTERIM REPAIR. AS SOON AS REPAIR PARTS ARE AVAILABLE (EXPECTED OCTOBER 2007), OWNERS WILL BE INSTRUCTED TO RETURN TO THE DEALERS FOR INSTALLATION OF A FUSED WIRING HARNESS. THE RECALL BEGAN ON AUGUST 13, 2007, AND MAILING COMPLETED BY SEPTEMBER 19, 2007. OWNERS MAY CONTACT FORD AT 1-888-222-2751.
IN ORDER TO ENHANCE POLICE OFFICE SAFETY, MODEL YEAR 1992-2003 CROWN VICTORIA POLICE INTERCEPTOR (CVPI) VEHICLES WILL BE EQUIPPED WITH SHIELDS DESIGNED TO HELP PROTECT THE FUEL TANK IN HIGH-SPEED REAR-IMPACT CRASHES. FORD ALSO WILL BE OFFERING AN OPTIONAL TRUNK PACKAGE DESIGNED TO IMPROVE THE SAFE TRANSPORT OF SHARP-EDGED, HEAVY EQUIPMENT IN THESE VEHICLES. Remedy: FORD HAS ADVISED US THAT SHIELD KITS HAVE BEEN AVAILABLE SINCE LATE OCTOBER AND WILL BE INSTALLED ON POLICE INTERCEPTOR VEHICLES AT NO COST. THE OPTIONAL TRANK PACKAGE WILL BE AVAILABLE BY THE END OF 2002. FORD HAS ESTABLISHED A NEW WEB SITE AT WWW.CVPI.COM TO ANSWER ADDITIONAL QUESTIONS ABOUT THE SAFE USE OF CPVI VEHICLES.
null Remedy: DEALERS WILL INSPECT THE REAR BRAKE LINES, AND IF NECESSARY, REPLACE A SECTION OF THE REAR BRAKE LINES IF IT IS LEAKING. ALSO THE RUBBER SHIELD ON THE LINE WILL BE INSPECTED TO VERIFY THAT IT IS PROPERLY LOCATED AND IT WILL BE SECURED WITH AN ADDITIONAL WORM-DRIVE TYPE CLAMP.
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE SPEED CONTROL DEACTIVATION SWITCH CAN DEVELOP A RESISTIVE SHORT IN THE ELECTRICAL CIRCUIT THAT COULD POTENTIALLY RESULT IN AN UNDERHOOD FIRE. A FIRE IS POSSIBLE BOTH WHEN THE VEHICLE IS RUNNING AND WHEN THE VEHICLE ENGINE IS OFF. ALSO, THE SHORT COULD DISABLE THE SPEED CONTROL SYSTEM OR CAUSE THE BRAKE LIGHT FUSE TO OPEN. Remedy: DEALERS WILL INSTALL A NEW SPEED CONTROL DEACTIVATION SWITCH AND CONNECTOR SHELL. OWNER NOTIFICATION BEGAN MAY 20, 1999.
INCORRECT INSTRUMENT PANEL WIRING ASSEMBLIES IN SOME VEHICLES WILL NOT ACTUATE THE "ANTI-LOCK" BRAKE WARNING LIGHTS. Remedy: MODIFY THE WIRE ASSEMBLY TO ALLOW ACTUATION OF THE ANTI-LOCK BRAKE WARNING LIGHTS.
VEHICLE DESCRIPTION: CERTAIN 1996-1999 FORD CROWN VICTORIA POLICE, FLEET, NATURAL GAS, AND 1996-1999 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT WERE PRODUCED WITH A LOWER CONTROL ARM BALL JOINT CONTAINING A ONE PIECE BEARING; AND 1990-1996 FORD CROWN VICTORIA POLICE, FLEET, AND NGV VEHICLES AND 1990-1996 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT HAVE BEEN SERVICED WITH EITHER A BALL JOINT CONTAINING THE ONE-PIECE BEARING OR A FRONT LOWER CONTROL ARM CONTAINING A BALL JOINT WITH A ONE-PIECE BEARING. THE ONE-PIECE BEARING WITHIN THE LOWER CONTROL ARM BALL JOINT CAN WEAKEN SLOWLY DURING USE AND EVENTUALLY CRACK. THIS COULD RESULT IN SEPARATION OF THE BALL AND CAP OF THE JOINT, ALLOWING THE CONTROL ARM TO DROP TO THE GROUND. Remedy: DEALERS WILL REPLACE THE LOWER CONTROL ARM BALL JOINTS (2).
AN UNUSED POWER SEAT HARNESS CONNECTOR IS POSITIONED ON THE RUBBER FLOOR MAT UNDER THE SEAT. IF THE VEHICLE IS OPERATED IN COLD WEATHER IN AREAS THAT HAVE LARGE AMOUNTS OF SALT USED FOR SNOW AND ICE CONTROL, A PUDDLE OF SALTWATER CAN ACCUMULATE ON THE RUBBER FLOOR MATS, REPEATEDLY WETTING THE CONNECTOR. THIS WILL RESULT IN CORROSION OF THE CONNECTOR, CAUSING A CURRENT TO FLOW BETWEEN THE TERMINALS WITHOUT TRIPPING THE CIRCUIT BREAKER. Remedy: DEALERS WILL REMOVE THE UNUSED CONNECTOR AND INSTALL A SEALED HEAT SHRINK CAP OVER THE AFFECTED WIRES.
VEHICLE DESCRIPTION: POLICE AND TAXI VEHICLES. THE HOOD LATCH STRIKER CAN WEAR OR BECOME DETACHED FROM THE HOOD. Remedy: DEALERS WILL INSTALL AN IMPROVED HOOD LATCH STRIKER (VEHICLES WITH 1992 MODEL HOODS) OR REVISED STRIKER PLATE ATTACHING FASTENERS (VEHICLES WITH 1993-1997 MODEL HOODS).
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain vehicles, a wiring harness that is not compatible with the vehicle circuit polarity may have been inadvertently installed during servicing for recall 2005028 or 2007258. As a result, the fuse is located in the output circuit rather than in the input power feed circuit, and will not offer the intended protection in the event of an electrical short to ground. This could result in a vehicle fire, causing property damage and/or personal injury. Correction: Dealers will install an updated wiring harness.
On certain vehicles, the speed control deactivation switch may overheat, smoke, or burn, potentially resulting in an underhood fire. The failure mode appears to be different than that of Recall 2005028 (05S28). This time, the concern is with long term durability performance issues causing the switch to fail. Correction: Initially as an interim repair, owners will be instructed to return their vehicles to their dealers to have the speed control deactivation switch disconnected. As soon as replacement parts are available, owners will be instructed to return to the dealers for installation of a fused wiring harness designed to eliminate the potential risk of fire.
Certain vehicles may experience a fire originating in the left front under hood area as a result of electrical overheating of the speed control deactivation switch. Correction: A new speed control deactivation switch and connector shell will be installed on affected vehicles.
Note: 1996-99 crown victoria police, fleet and ngv and lincoln town car limousine equipped with a lower control arm ball joint containing a one piece bearing and 1990-96 crown victoria police, fleet and ngv and lincoln town car limousine that were serviced with either a ball joint containing an one piece bearing or a front lower control arm with a one piece bearing. High bearing loads can lead to thinning and eventual cracking of the lower control arm ball joint. This can result in separation of the ball and cap of the joint. Should this occur, the control arm to which the cap is mounted will drop to the ground. Should this occur while the vehicle is moving, reduced steering control could result in a collision. Correction: Lower control arm ball joints will be replaced.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Crash-test ratings from NHTSA's New Car Assessment Program.
Source: NHTSA (US Department of Transportation) · US public domain
NOTE: POLICE AND TAXI VEHICLES ONLY. THE HOOD LATCH STRIKER MAY EITHER WEAR OR BECOME DETACHED FROM THE HOOD. EITHER OF THESE CONDITIONS MAY RESULT IN THE HOOD OPENING WITHOUT WARNING WHILE THE VEHICLE IS BEING OPERATED RESULTING IN REDUCED DRIVER VISIBILITY AND A POSSIBLE CRASH. CORRECTION: VEHICLES WITH 1992 MODEL HOODS WILL HAVE AN IMPROVED HOOD LATCH STRIKER INSTALLED AND REVISED STRIKER PLATE ATTACHING FASTENERS WILL BE INSTALLED ON VEHICLES WITH 1993-97 HOODS.
THESE VEHICLES MAY HAVE BEEN BUILT WITH AN UNUSED POWER SEAT HARNESS CONNECTOR THAT WAS POSITIONED ON THE FLOOR MAT UNDER THE SEAT. IN AREAS WHERE ROAD SALT IS USED, A BRINE MAY ACCUMULATE ON THE FLOOR MATS AND REPEATEDLY WET THE CONNECTOR. THIS COULD CORRODE THE CONNECTOR AND RESULT IN A SALT BRIDGE BETWEEN THE TERMINALS CAUSING CURRENT FLOW WHICH COULD OVERHEAT THE CONNECTOR WITH RESULTANT FUMES AND A POSSIBLE FIRE. CORRECTION: UNUSED CONNECTORS WILL BE REMOVED AND SEALED HEAT SHRINK CAPS WILL BE PLACED OVER THE AFFECTED WIRES.
Certain vehicles do not comply with CMVSSS. 208 - seat belt installations. The french language version of the air bag maintenance/information/instruction label was not installed. Note: for taurus models only police and sho vehicles are affected. Correction: French language labels will be mailed to affected owners.