Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1993 Volkswagen Corrado, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH VR6 ENGINES. A COOLANT SYSTEM COMPONENT SUCH AS THE THERMO SWITCH, RADIATOR FAN, OR WATER PUMP, CAN MALFUNCTION CAUSING THE COOLANT TEMPERATURE AND COOLANT SYSTEM PRESSURE TO INCREASE SIGNIFICANTLY. OVER TIME, EXCESSIVE PRESSURE CAN CAUSE LEAKAGE OF COOLANT FROMTHE SYSTEM, INCLUDING LEAKAGE FROM THE HEAT EXCHANGER. Remedy: DEALERS WILL INSTALL IN THE COOLANT INLET HOSE TO THE HEATER CORE, A PRESSURE REDUCER WITH A 5MM DIAMETER SECURED BY A SPRING TENSIONED HOSE CLAMP. ALSO A NEW RELAY THAT WILL CHANGE THE OPERATION OF THE SECONDARY ELECTRICAL COOLANT PUMP WILL BE INSTALLED. DEALERS WILL ALSO PERFORM A FUNCTIONAL CHECK OF THE COOLING SYSTEM TO MAKE SURE THAT ALL COOLING SYSTEM COMPONENTS OPERATE PROPERLY.
AN ENGINE COMPARTMENT ELECTRICAL WIRING HARNESS MAY HAVE BEEN ROUTED TOO CLOSE TO A SHEET METAL EDGE. THE WIRING CAN BECOME DAMAGED DURING NORMAL VEHICLE OPERATION DUE TO CHAFING, RESULTING IN AN ELECTRICAL SHORT. Remedy: REROUTE AND SECURE VARIOUS WIRING HARNESSES INSIDE THE ENGINE COMPARTMENT.
IMPROPER MATERIAL WAS USED IN MANUFACTURING THE RADIATOR FAN MOTOR SHAFT CAUSING THE SHAFT TO WEAR AND BECOME NOISY. Remedy: DEALERS WILL REPLACE THE COMPLETE COOLING FAN ASSEMBLY ON VEHICLE HAVING THE POTENTIAL SHAFT MATERIAL PROBLEM. DEALERS WILL INSTALL A NEW FAN BLADE INCLUDING A NEW LOCK NUT ON VEHICLE WITH LOOSE FAN BLADE LOCK NUTS.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain vehicles, excessive temperature and cooling system pressure could result in coolant leakage in the system including leakage from the heat exchanger. Leakage of coolant from the heat exchanger could cause injury to the feet of the driver, steam up the interior of the vehicle and temporarily impair the driver's vision. Correction: Dealer will conduct a functional check of the cooling system and install a pressure throttle which will result in reduced coolant pressure in the heat exchanger.
NOTE: INCLUDES PASSAT, GOLF AND JETTA TURBO DIESEL. ON 1993-94 MODELS, THE RADIATOR FAN MOTOR SHAFT COULD SEIZE AND RENDER THE FAN MOTOR INOPERATIVE. 1994-95 MODELS COULD EXPERIENCE A CONDITION WHEREBY THE LOCK NUT SECURING THE RADIATOR FAN BLADE HUB TO THE MOTOR COULD LOSE ITS REQUIRED TORQUE. A LOOSE LOCK NUT COULD CAUSE THE FAN HUB TO LOOSEN FROM THE SHAFT AND CAUSE THE BELT PULLEY TO RUN "OFF-CENTER". THIS IN TURN COULD CAUSE THE FAN BELT TO DISCONNECT OR BREAK. EITHER OF THE ABOVE CONDITIONS COULD RESULT IN ENGINE OVERHEATING AND STALLING. A VEHICLE STALLING IN TRAFFIC COULD CAUSE AN ACCIDENT. CORRECTION: VEHICLES WITH EITHER HAVE THE COMPLETE COOLING FAN ASSEMBLY REPLACED OR A NEW FAN BLADE WITH A NEW LOCK NUT INSTALLED.
AN ELECTRICAL WIRING HARNESS IN THE ENGINE COMPARTMENT COULD BECOME DAMAGED DUE TO CHAFING. THIS COULD RESULT IN AN ELECTRICAL SHORT CAUSING THE ENGINE TO STALL OR THE RADIATOR FAN TO STOP OPERATING, CAUSING THE ENGINE TO OVERHEAT. EITHER CONDITION COULD CAUSE AN ACCIDENT. CORRECTION: WIRING HARNESS WILL BE RE-ROUTED AND SPECIAL SHIELDING WILL BE INSTALLED IN ALL AFFECTED VEHICLES.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
THE FUEL HOSE ATTACHED TO THE FUEL DISTRIBUTION RAIL, LOCATED IN THE ENGINE COMPARTMENT, MAY NOT BE ADEQUATELY CLAMPED. THIS COULD LEAD TO FUEL SEEPAGE AT THE HOSE CONNECTION. ESCAPING FUEL COULD COME INTO CONTACT WITH HOT ENGINE COMPONENTS AND POSSIBLY CAUSE AN ENGINE COMPARTMENT FIRE. CORRECTION: FUEL HOSE ATTACHED TO THE FUEL RAIL WILL BE REPLACED AND EXISTING HOSE CLAMPS WILL BE REPLACED WITH A NEW SPRING TYPE HOSE CLAMP.