Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1996 Volvo WIA, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
CERTAIN HEAVY DUTY CLASS 8 TRUCKS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THE TWO TAIL LAMPS, BACK-UP LAMP,AND LICENSE TAG LAMP WERE MOUNTED ON INSUFFICIENTLY RIGID MOUNTS. Remedy: DEALERS WILL ATTACH THE TWO TAIL LAMPS, BACK-UP LAMP, AND THE LICENSE TAP LAMP ON STIFFER BRACKETS. OWNER NOTIFICATION BEGAN OCTOBER 31, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT VOLVO TRUCKS AT 1-800-528-6586.
WARNING LABELS IDENTIFYING THE CLIMBING SEQUENCE AND PROCESS WERE OMITTED. Remedy: VOLVO HEAVY TRUCK WILL BE PROVIDING WARNING LABELS TO BE INSTALLED BY OWNERS ON THEIR TRUCKS.
VEHICLE DESCRIPTION: CLASS 8 HEAVY DUTY VEHICLES EQUIPPED WITH EATON DRIVE AXLES AND AXILOK SPINDLE NUTS. THE DRIVE AXLE HOUSINGS CONSIST OF A PLATE STEEL CENTER SECTION AND TWO FORGED SPINDLES, ONE OF WHICH IS WELDED TO EACH END OF THE CENTER SECTION. EACH SPINDLE CONTAINS A KEYWAY SLOT IN WHICH THE LOCKING TAB FOR THE WHEEL BEARING NUT LOCKING MECHANISM IS INSERTED. THE LENGTH OF THE KEYWAY SLOT MAY NOT BE LONG ENOUGH TO ACCOMMODATE THE TAB CAUSING THE TAB TO BE DEFORMED OR DAMAGED DURING INSTALLATION. Remedy: DEALERS WILL REPLACE THE DRIVE AXLE HOUSING NUTS WITH A CONVENTIONAL WHEEL NUT HARDWARE SYSTEM.
THE TRACTION SOLENOID EXHAUST CAN BE OBSTRUCTED DUE TO INADEQUATE DRAINAGE AND A BUILD-UP OF ROAD CONTAMINATION BETWEEN THE MOUNTING BRACKET AND THE SOLENOID HOUSING. THE OBSTRUCTED EXHAUST PREVENTS THE RELAY VALVE CONTROL AIR PRESSURE FROM VENTING AFTER A DIFFERENTIAL BRAKING TRACTION EVENT. Remedy: DEALERS WILL REMOVE THE SUSPECT VALVE AND INSTALL A NEW VALVE THAT HAS A MODIFIED SOLENOID HOUSING WHICH WILL ALLOW FOR SUFFICIENT DRAINAGE AND A NEW VALVE MOUNTING BRACKET WITH INCREASED HEIGHT TO REDUCE ENTRY OF CONTAMINATION.
VEHICLE DESCRIPTION: CLASS 8 HEAVY DUTY TRUCKS. THE AIR SUSPENSION CONTROL VALVE SUPPLY LINE WAS NOT PLUMBED THROUGH AN AIR PRESSURE PROTECTION VALVE. IN THE EVENT OF A FAILURE, THERE WOULD BE LOSS OF AIR PRESSURE IN THE 'B' SYSTEM AIR RESERVOIR THAT SUPPLIES AIR PRESSURE FOR THE FRONT STEER AXLE BRAKES. Remedy: DEALERS WILL INSTALL THE NECESSARY AIR PRESSURE PROTECTION VALVE.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH DESIGN LEVEL 1, ROCKWELL FF980 SERIES FRONT AXLE. THE FRONT AXLE HUB FLANGE CAN DEVELOP CRACKS DUE TO HIGH STRESS LEVELS. Remedy: DEALERS WILL REMOVE AND REPLACE THE FRONT HUBS WITH AN IMPROVED DESIGN LEVEL 2 HUB.
VEHICLE DESCRIPTION: HEAVY DUTY CLASS 8 VEHICLES BUILT WITH A VOLVO 5.7 (12,500 LBS) FRONT STEERING AXLE. DUE TO HYDROGEN EMBRITTLEMENT, THE FRONT STEERING AXLE KING PINS COULD HAVE BROKEN DURING ASSEMBLY. CONTINUED OPERATION OF A VEHICLE WITH A BROKEN KING PIN COULD ALLOW THE PIN TO WORK LOOSE. Remedy: DEALERS WILL INSPECT THE VEHICLES FOR A BROKEN KING PIN AND REPLACE THE KING PINS IF BROKEN.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain vehicles, the air ride suspension control valve supply line is not plumbed through an air pressure protection valve. In the event of an air suspension bag failure, there will be loss of air pressure in the "b" system which supplies air pressure to the front steer axle brakes. This could result in loss of front steer axle brakes and increased stopping distances. Correction: Air pressure protection valve will be installed.
WARNING LABELS IDENTIFYING THE CLIMBING SEQUENCE AND PROCESS (ONE FOOT AND TWO HANDS OR TWO FEET AND ONE HAND) WERE OMITTED WHEN THESE VEHICLES WERE ASSEMBLED. PERSONS NOT USING THE SEQUENCE AND PROCESS DURING CAB ENTRY OR EXIT MAY BE SUBJECT TO RISK OF SLIP AND/OR FALL. CORRECTION: WARNING LABELS AND INSTALLATION INSTRUCTIONS WILL BE MAILED TO OWNERS.
NOTE: VEHICLES EQUIPPED WITH NEWAY ANCHORLOK REAR SUSPENSIONS. THE SUSPENSION EQUALIZING BEAM COULD HAVE DEFECTIVE SUSPENSION SHAFTS WHICH COULD FRACTURE INSIDE THE BEAM AND WORK LOOSE FROM THE BEAM. SHOULD THE SHAFT SEPARATE FROM THE BEAM, THE TRANSVERSE BEAM COULD CONTACT THE ROADWAY GENERATING SPARKS. THIS CONDITION MIGHT ALSO AFFECT VEHICLE STABILITY AND CONTROL WHICH COULD POSE A HAZARD TO OTHER USERS OF THE ROADWAY AND ADJACENT PROPERTY. CORRECTION: ALL EQUALIZING BEAMS WITH NON-CONFORMING SHAFTS WILL BE REPLACED.
DUE TO HYDROGEN EMBRITTLEMENT, THE KING PIN USED IN THE VOLVO 5.7 (12,500 LB) FRONT STEER AXLE MAY HAVE BEEN BROKEN DURING ASSEMBLY OF THE AXLE. CONTINUED OPERATION OF A VEHICLE WITH A BROKEN KING PIN MAY ALLOW THE PIN TO WORK LOOSE, CAUSE ERRATIC STEERING, AND RESULT IN POTENTIAL FOR LOSS OF STEERING CONTROL AND A VEHICLE CRASH. CORRECTION: VEHICLES WILL BE INSPECTED AND KING PIN REPLACED IF REQUIRED.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain