Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1997 Chevrolet Cavalier, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
CERTAIN CK MOTORSPORTS COMBINATION HEADLIGHTS, CLEAR CORNER, BUMPER, AND SIDE MARKER LIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON THE PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT. Remedy: CK MOTORSPORT WILL NOTIFY OWNERS AND REPLACE THE NONCOMPLIANT LAMPS FREE OF CHARGE. THE RECALL BEGAN ON JULY 1, 2006. OWNERS MAY CONTACT CK MOTORSPORT AT 1-909-610-7211.
DORMAN PRODUCTS IS RECALLING 3,900 INTERMEDIATE STEERING SHAFTS DORMAN PART NOS. 425-151, 425-152, AND 425-153, (SOLD UNDER DORMAN'S "OE SOLUTIONS" BRAND NAME), BALKAMP #'S 7-3057, 7-3058, 7-3059 (SOLD UNDER THE "NAPA" BRAND NAME), AND PLATINUM PARTS #'S 2425151, 2425152, AND 2425153 MANUFACTURED DURING THE MONTH OF SEPTEMBER 2007. THESE REPLACEMENT STEERING SHAFTS CAN BE USED ON THE VEHICLES LISTED ABOVE. THE WELD CONNECTING THE INNER TUBE TO THE OUTER TUBE MAY BE DEFECTIVE. Remedy: DORMAN WILL NOTIFY OWNERS AND REPLACE THE STEERING SHAFTS FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 16, 2008. OWNERS MAY CONTACT DORMAN TOLL FREE AT 1-800-523-2492.
DOPE, INC. IS RECALLING 42,540 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS. Remedy: DOPE, INC. WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON JULY 28, 2009. OWNERS MAY CONTACT DOPE, INC. AT 1-626-272-1798.
CERTAIN PRO-A MOTORS CORNER LAMPS, TURN SIGNALS, AND HEADLIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON CERTAIN PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT. Remedy: PRO-A MOTORS WILL NOTIFY OWNERS AND OFFER TO REPURCHASE THE LAMPS. THE RECALL BEGAN ON APRIL 3, 2006. OWNERS MAY CONTACT PRO-A MOTORS AT 323-838-2988.
SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS. Remedy: SABERSPORT WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON MAY 11, 2009. OWNERS MAY CONTACT SABERSPORT AT 1-909-598-7589.
ON CERTAIN PASSENGER VEHICLES. IF THE ENGINE FAILS TO START AND THE DRIVER HOLDS THE KEY IN THE "START" POSITION FOR AN EXTENDED PERIOD, HIGH CURRENT FLOWS THROUGH THE IGNITION SWITCH, AND SOMETIMES PRODUCES ENOUGH HEAT TO MELT INTERNAL SWITCH PARTS. Remedy: DEALERS WILL INSTALL A RELAY KIT IN THESE VEHICLES TO PREVENT HIGH CURRENT FROM FLOWING THROUGH THE IGNITION SWITCH. OWNER NOTIFICATION BEGAN MARCH 27, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT CHEVROLET AT 1-800-222-1020, PONTIAC AT 1-800-762-2737, BUICK AT 1-800-521-7300, OR OLDSMOBILE AT 1-800-442-6537.
CERTAIN DELPHI AFTERMARKET FUEL PUMP MODULES / MODULE RESERVOIR ASSEMBLIES (MRA) THAT WERE SOLD FOR USE ON THE ABOVE LISTED VEHICLES. DURING PRODUCTION THE MRAS VENT AND FUEL RETURN TUBES WERE REVERSED. THIS CONDITION CAN RESULT IN THE VEHICLE NOT RUNNING CORRECTLY (IDLE ROUGH AND/OR STALL) DUE TO AN OVERLY RICH FUEL BLEND OR THE VEHICLE'S EVAPORATIVE EMISSION CARBON CANISTER MAY LEAK FUEL. Remedy: DELPHI WILL NOTIFY OWNERS AND REPLACE THE DEFECTIVE MRAS FREE OF CHARGE. THE RECALL BEGAN ON MARCH 20, 2007. OWNERS CAN CONTACT DELPHI AT 1-877-335-7443.
CERTAIN PASSENGER VEHICLES AND MINI VANS HAVE LOWER PINION BEARINGS IN THE POWER RACK AND PINION ASSEMBLY IN WHICH THE RETAINER TABS WERE NOT CRIMPED PROPERLY. THESE AND SOME OTHER RETAINERS USED IN VEHICLES ASSEMBLED BETWEEN JANUARY 1, 1996 AND OCTOBER 31, 1997, COULD FAIL AND PERMIT THE BALL BEARINGS TO ESCAPE. Remedy: DEALERS WILL INSTALL A NEW LOWER PINION BEARING UNLESS INSPECT OF THE EXISTING BEARING INDICATES THAT REPLACEMENT OF THE GEAR ASSEMBLY IS NECESSARY. OWNER NOTIFICATION BEGAN JANUARY 24, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT CHEVROLET AT 1-800-222-1020, PONTIAC AT 1-800-762-2737, OR OLDSMOBILE AT 1-800-442-6537.
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE COMPACT SPARE TIRE ASSEMBLIES WERE ASSEMBLED WITH INCORRECT RIMS. IF THE SPARE TIRE IS UNDERINFLATED, THE BEAD CAN SEPARATE FROM THE RIM CAUSING A RAPID LOSS OF AIR. THIS DOES NOT COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 110, "TIRE SELECTION AND RIMS." Remedy: DEALERS WILL REPLACE THE RIM ON THE COMPACT SPARE TIRE ASSEMBLY. OWNERS ARE REQUESTED NOT TO USE THE SPARE TIRE UNTIL THE RIM HAS BEEN REPLACED.
VEHICLE DESCRIPTION: PASSENGER VEHICLES. ONE OF THE REAR SUSPENSION TRAILING ARM BOLTS CAN FATIGUE AND BREAK. Remedy: DEALERS WILL REPLACE THE REAR SUSPENSION TRAILING ARM FASTENERS.
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THESE VEHICLES WERE BUILT WITH MIS-LOCATED WELDS AT THE JOINT BETWEEN THE LEFT ROCKER PANEL INNER REINFORCEMENT AND THE BODY SIDE RING. THIS DOES NOT MEET THE REQUIREMENTS OF FMVSS NO. 214, "SIDE DOOR STRENGTH." Remedy: DEALERS WILL INSPECT THE WELDS AND, IF NECESSARY, PLACE FIVE WELDS BETWEEN THE INVOLVED PANELS AND APPLY PRIMER AND TOPCOAT FINISH MATERIALS.
THESE VEHICLES WERE BUILT WITH AN INCORRECT WIPER BLADE ASSEMBLY (17" LONG INSTEAD OF 22" LONG) ON THE DRIVER'S SIDE. THIS DOES NOT COMPLY WITH FMVSS NO. 104, "WINDSHIELD WIPING AND WASHING SYSTEMS." Remedy: DEALERS WILL INSPECT FOR THE CORRECT WIPER BLADE ASSEMBLY AND INSTALL A CORRECT LENGTH WIPER BLADE ASSEMBLY.
VEHICLE DESCRIPTION: PASSENGER VEHICLES. BECAUSE OF CERTAIN CALIBRATIONS IN THE AIR BAG'S SENSING AND DIAGNOSTIC MODULE, AN INADVERTENT AIR BAG DEPLOYMENT COULD OCCUR IN A LOW SPEED CRASH OR WHEN AN OBJECT STRIKES THE FLOOR PAN. Remedy: DEALERS WILL RECALIBRATE THE AIR BAG SENSING AND DIAGNOSTIC MODULE.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Certain vehicles, after being exposed to substantial amounts of water, may experience deployment of either the driver or passenger front airbag without a crash. The owner’s manual for these vehicles does not provide specific information about this situation. Inadvertent deployment of the driver and / or passenger front airbag in a non-accident (non-impact) situation may cause damage to the surrounding vehicle environment (windshield / instrument panel), and create expensive vehicle repair, including replacement of the airbag module(s) and the Sensing and Diagnostic Module (SDM). In some instances, inadvertent deployment could cause minor injuries to vehicle occupants. Correction: GM will notify the owners of these 1996 and 1997 vehicles of the potential affect of water accumulating in the vehicle interior on the function of the airbag system (as included in the owner's manuals of 1998 and later model years vehicles).
On certain vehicles, the lower pinion bearings retainer tabs were not crimped properly. These and some other retainers used in vehicles assembled between January 1, 1996 and October 31, 1997 may fail and permit the ball bearings to escape. If the problem were to occur, the driver would have to exert more effort to turn the steering wheel. Correction: Dealers are to inspect the condition of the lower bearing, and replace the lower pinion bearing or the rack and pinion steering gear assembly, if necessary.
On certain passenger vehicles if the engine fails to start and the driver holds the key in the "start" position for an extended period, high current flows through the ignition switch, and sometimes produces enough heat to melt internal switch parts. If the switch is damaged, a fire could occur in the steering column, even with the engine off and the key removed. Correction: Dealers will install a relay kit in these vehicles to prevent high current from flowing through the ignition switch.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Crash-test ratings from NHTSA's New Car Assessment Program.
Source: NHTSA (US Department of Transportation) · US public domain
Note: Certain 1997-99 vehicles in Ontario, Quebec and the Atlantic provinces and 1995-99 vehicles in all other provinces and territories. Moisture may enter the Powertrain Control Module (PCM) as a result of corrosion after extended exposure to road salt. This can lead to symptoms including illumination of the "Check Engine" light or the engine running rough. If these symptoms are ignored the engine may stall and may not be able to be restarted. Correction: Dealers will seal the Powertrain Control Module (PCM) in a protective shield/cover assembly.
Certain vehicles may have a condition which could result in one of the rear suspension trailing arm bolts breaking. If this were to occur while the vehicle was in motion, vehicle control would be affected and a crash could occur without prior warning. Correction: Dealers will replace the rear suspension trailing arm fasteners.
BECAUSE OF CERTAIN CALIBRATIONS IN THE AIR BAG'S COMPUTER, THERE IS AN INCREASED RISK OF AN AIR BAG DEPLOYMENT IN A LOW SPEED CRASH OR WHEN AN OBJECT STRIKES THE FLOOR PAN. CORRECTION: THE SDM MODULE WILL BE RECALIBRATED TO REDUCE THE SENSITIVITY TO SHORT AND MID-DURATION COMMANDED DEPLOYMENTS.
THESE VEHICLES MAY NOT COMPLY WITH C.M.V.S.S. 214 - SIDE DOOR STRENGTH. THERE MAY BE MIS-LOCATED WELDS AT THE JOINT BETWEEN THE LEFT ROCKER PANEL INNER REINFORCEMENT AND THE BODY SIDE RING. IN THE EVENT OF A VEHICLE CRASH, THE SHEET METAL STRUCTURE MAY NOT PERFORM AS DESIGNED. THIS COULD RESULT IN REDUCED LEVELS OF OCCUPANT PROTECTION. CORRECTION: VEHICLES WILL BE INSPECTED FOR MIS-LOCATED WELDS AND, IF NECESSARY, UP TO FIVE WELDS WILL BE PLACED BETWEEN THE INVOLVED PANELS.
THESE VEHICLES DO NOT COMPLY WITH C.M.V.S.S. 110 - TIRE SELECTION AND RIMS. THE COMPACT SPARE TIRE ASSEMBLIES IN THESE VEHICLES MAY HAVE BEEN ASSEMBLED WITH RIMS THAT DO NOT CONFORM TO DIMENSIONAL AND PROFILE STANDARDS. IF THE TIRE IS UNDERINFLATED IT CAN SEPARATE FROM THE RIM. CORRECTION: RIM ON THE COMPACT SPARE TIRE ASSEMBLY WILL BE REPLACED.