Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1997 Kenworth W900, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH MERITOR FG941 STEER AXLES. THE GROSS AXLE WEIGHT RATING (GAWR) WAS DETERMINED INCORRECTLY AND OVER-STATED ON THE VEHICLE CERTIFICATION LABEL. WITH THE INCORRECT GAWR LISTED, THESE LABELS DO NOT MEET THE CERTIFICATION REQUIREMENTS OF PART 567, "REQUIREMENTS FOR MANUFACTURERS OF MOTOR VEHICLES." VEHICLES WILL BE REMEDIED EITHER BY ASSIGNING THE PROPER WEIGHT RATING OR, IF POSSIBLE, BY CHANGING THE NECESSARY COMPONENTS TO MEET THE CURRENTLY ASSIGNED WEIGHT RATING. Remedy: VEHICLES WILL BE REMEDIED EITHER BY ASSIGNING THE PROPER WEIGHT RATING OR, IF POSSIBLE, BY CHANGING THE NECESSARY COMPONENTS TO MEET THE CURRENTLY ASSIGNED WEIGHT RATING. OWNER NOTIFICATION BEGAN JUNE 22, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT KENWORTH AT 1-425-828-5000.
VEHICLE DESCRIPTION: VEHICLES EQUIPPED WITH 54" REAR AXLE SPACING CONFIGURATION OF THE AIRGLIDE 200 SUSPENSION WITH THE SERVICE APPLICATION IDENTIFIED AS LOGGER, DUMP TRUCK, OR TANKER. THE REAR SUSPENSION IS REGULARLY SUBJECTED TO EXTREME ARTICULATION, RESULTING IN FLEXING OF THE JOINT. Remedy: DEALERS WILL REPLACE THE LOWER SWAY ARM BRACKETS. OWNER NOTIFICATION BEGAN MARCH 27, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT KENWORTH AT 1-425-828-5000.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH KENWORTH AIRGLIDE 200 REAR SUSPENSION. DUE TO MATERIALS USED IN THE SWAY BAR ARMS AND STUDS AS WELL AS THE STUD PLATING MATERIAL, STRESS CORROSION CRACKING AND BENDING FATIGUE CAN OCCUR IN THE REAR SUSPENSION SWAY BAR ARMS AND STUDS CAUSING THE STUD TO FAIL PREMATURELY. Remedy: DEALERS WILL REPLACE THE ARM ASSEMBLY MANUFACTURED FROM A DIFFERENT MATERIAL. NEW STUDS WILL BE INSTALLED WITH DIFFERENT THREADS AND DIFFERENT FINISH.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH DESIGN LEVEL 1, ROCKWELL FF980 SERIES FRONT AXLE. THE FRONT AXLE HUB FLANGE CAN DEVELOP CRACKS DUE TO HIGH STRESS LEVELS. Remedy: DEALERS WILL REMOVE AND REPLACE THE FRONT HUBS WITH AN IMPROVED DESIGN LEVEL 2 HUB.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH CATERPILLAR 3406E ENGINES. THE ROUTING OF THE ELECTRICAL AND FUEL LINES CAN CAUSE CHAFFING OF THE WIRING HARNESS ON THE FUEL LINE. Remedy: DEALERS WILL INSPECT, ADJUST, AND REPAIR, IF NECESSARY, THE FUEL LINE AND ELECTRICAL HARNESS.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Certain heavy duty trucks equipped with Meritor FG941 steer axles. The Gross Axle Weight Rating (GAWR) was determined incorrectly and over-stated on the vehicle certification label. Correction: Vehicles will be remedied either by assigning the proper weight rating or, if possible, by changing the necessary components to meet the currently assigned weight rating.
On certain vehicles, the rear suspension is regularly subjected to extreme articulation, resulting in flexing of the joint. Failure of the lower sway arm attaching bolts could result with possible loss of vehicle control. Correction: Dealers will replace the lower sway arm brackets.
NOTE: VEHICLES EQUIPPED WITH AIRGLIDE 200 REAR SUSPENSION. DUE TO THE MATERIALS USED IN THE SWAY BAR ARMS AND THE STUDS AS WELL AS THE STUD PLATING, A COMBINATION OF STRESS CORROSION CRACKING AND BENDING FATIGUE CAN OCCUR WHICH COULD CAUSE THE STUD TO FAIL PREMATURELY. THIS COULD RESULT IN LOSS OF VEHICLE CONTROL AND A CRASH WITHOUT PRIOR WARNING. CORRECTION: SWAY BAR ARM ASSEMBLY WILL BE REPLACED WITH ONE OF A DIFFERENT MATERIAL. THE NEW STUDS WILL HAVE DIFFERENT THREADS AND A DIFFERENT FINISH.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain