Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1998 Ford Explorer, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
ON CERTAIN TRUCKS EQUIPPED WITH SPEED CONTROL, GASOLINE OR NATURAL GAS ENGINES, THE SPEED CONTROL DEACTIVATION SWITCH MAY OVERHEAT. Remedy: DEALERS WILL INSTALL A FUSED WIRING HARNESS INTO THE SPEED CONTROL SYSTEM FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 7, 2006. OWNERS MAY CONTACT FORD AT 1-866-436-7332. (NOTE: ALSO SEE RECALLS 05V017 AND 05V388)
DOPE, INC. IS RECALLING 42,540 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS. Remedy: DOPE, INC. WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON JULY 28, 2009. OWNERS MAY CONTACT DOPE, INC. AT 1-626-272-1798.
FORD IS RECALLING MODEL YEARS 1995-2003 WINDSTAR, 2000-2003 EXCURSION DIESEL, 1993-1997 AND 1999-2003 F-250 SD THROUGH F-550 SD DIESEL, 1992-2003 E-150 THROUGH E-550, 1995-2002 EXPLORER, 1997 AND 2002 MERCURY MOUNTAINEER, 1995-1997 AND 2001-2003 RANGER, AND 1994 F53 VEHICLES EQUIPPED WITH THE TEXAS INSTRUMENTS SPEED CONTROL DEACTIVATION SWITCH (SCDS). THE SCDS MAY LEAK INTERNALLY AND THEN OVERHEAT, SMOKE, OR BURN. Remedy: FORD WILL NOTIFY OWNERS THAT DEALERS WILL INSTALL A FUSED WIRING HARNESS IN LINE WITH THE SCDS. ON 1999-2003 WINDSTAR VEHICLES WITH A LEAKING SCDS, DEALERS WILL ALSO INSPECT THE ABS CONTROL MODULE CONNECTOR AND REPAIR AS NECESSARY. REPAIRS WILL BE COMPLETED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON OCTOBER 27, 2009. OWNERS MAY CONTACT FORD AT 1-888-222-2751.
SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS. Remedy: SABERSPORT WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON MAY 11, 2009. OWNERS MAY CONTACT SABERSPORT AT 1-909-598-7589.
VEHICLE DESCRIPTION: MINI VANS, LIGHT PICKUP TRUCKS, AND SPORT UTILITY VEHICLES. OFF LEASE CANADIAN VEHICLES EQUIPPED WITH DAYTIME RUNNING LIGHTS WHICH MEET CANADIAN REQUIREMENTS AND NOT THE PHOTOMETRIC REQUIREMENTS OF FMVSS 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." ACCORDING TO FORD, THE VEHICLES WERE IMPORTED INTO THE U.S. ERRONEOUSLY. Remedy: DEALERS WILL BE ADVISED TO DEACTIVATE THE RUNNING LIGHT FUNCTION AND TO COMPLETE ANY OUTSTANDING SAFETY RECALLS ON THESE VEHICLES.
CERTAIN PRO-A MOTORS CORNER LAMPS, TURN SIGNALS, AND HEADLIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON CERTAIN PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT. Remedy: PRO-A MOTORS WILL NOTIFY OWNERS AND OFFER TO REPURCHASE THE LAMPS. THE RECALL BEGAN ON APRIL 3, 2006. OWNERS MAY CONTACT PRO-A MOTORS AT 323-838-2988.
TIRE DESCRIPTION: FIRESTONE WILDERNESS AT, SIZE P235/75R15, PRODUCED AT THE DECATUR, ILLINOIS TIRE PLANT AND ALL FIRESTONE RADIAL ATX AND RADIAL ATX II TIRES, SIZE P235/75R15. OPERATION OF THESE TIRES AT LOW INFLATION PRESSURES, HIGH SPEED, AND IN HOT WEATHER, CAN CONTRIBUTE TO SEPARATION OF THE TIRE TREAD. Remedy: THE REPLACEMENT/REIMBURSEMENT PROGRAM FOR THIS CAMPAIGN EXPIRED ON AUGUST 29, 2001. HOWEVER, CUSTOMERS SHOULD CONTACT FIRESTONE CUSTOMER SERVICE AT 1-800-465-1904 FOR POSSIBLE ASSISTANCE.
VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES EQUIPPED WITH 4.0L SOHC ENGINES AND STILL RETAIN THE ORIGINAL THROTTLE BODY (PART NUMBERS 97JF-9E926AB OR 97JF-9E926-AC). SOME OF THE ORIGINAL THROTTLE BODIES INSTALLED ALLOWED A GAP BETWEEN THE PLATE AND BORE TO BE BUILT TOO NARROW. THIS REDUCED CLEARANCE ALLOWED THE ENGINE DEPOSITS NORMALLY PRESENT IN THE THROTTLE BODY TO CONTACT OR BRIDGE THE GAP. IF THE ENGINE DEPOSITS BRIDGED THE GAP BETWEEN THE THROTTLE PLATE AND BORE AND THEN HARDENED, ON THE INITIAL APPLICATION OF THE ACCELERATOR PEDAL AFTER THE ENGINE HAS COOLED, THE OPERATOR WOULD NEED TO APPLY ADDITIONAL FORCE TO THE ACCELERATOR PEDAL TO BREAK THE BRIDGE. Remedy: DEALERS WILL REPLACE THE ORIGINAL THROTTLE BODIES.
ON CERTAIN SPORT UTILITY VEHICLES EQUIPPED WITH HIGH BACK SEATS, THE UPPER BOLT ON THE DRIVER'S SIDE HIGH BACK SEAT, THAT ATTACHES THE SEAT RECLINER MECHANISM TO THE SEAT BACK FRAME, COULD FRACTURE. IF THE BOLT FRACTURES AND DOES NOT JAM IN THE SEAT BACK FRAME, THE SEAT BACK MAY RECLINE UNTIL IT MAKES CONTACT WITH AN OBJECT BEHIND THE SEAT, SUCH AS THE SECOND ROW SEAT CUSHION. Remedy: DEALERS WILL REPLACE THE DRIVER SEAT UPPER BOLT WITH A METAL SPACER AND BOLT. IN ADDITION, SEATS WITH TUBULAR BACK FRAMES WILL HAVE THE FULLY THREADED LOWER RECLINER BOLT REPLACED WITH A PARTIALLY THREADED BOLT. OWNER NOTIFICATION BEGAN ON AUGUST 29, 2003. OWNERS SHOULD CONTACT FORD AT 1-800-392-3673.
THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH THE SAFETY ACT. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. EQUIPMENT DESCRIPTION: FORD IS REPLACING ALL FIRESTONE WILDERNESS AT 15, 16, AND 17 INCH TIRES MOUNTED ON FORD TRUCKS AND SUVS. FORD REPORTS TREAD SEPARATION CAN OCCUR DUE TO A COMBINATION OF THE SENSITIVITY OF THE TIRE DESIGN TO STRESS, AGING, AND MANUFACTURING DIFFERENCES BETWEEN PLANTS. FORD IS REPLACING THESE TIRES TO PREVENT POSSIBLE PREMATURE TIRE FAILURE. VEHICLE DESCRIPTION: THE VEHICLES LISTED BELOW MAY HAVE BEEN ORIGINALLY EQUIPPED WITH FIRESTONE WILDERNESS AT TIRES OR MAY HAVE HAD WILDERNESS AT TIRES INSTALLED DURING THE FIRESTONE RECALL LAUNCHED IN AUGUST 2000. CERTAIN 1991 THROUGHT 2002 FORD EXPLORER CERTAIN 2001 THROUGHT 2002 EXPLORER SPORT, AND SPORT TRAC CERTAIN 1997 THROUGH 2002 MERCURY MOUNTAINEER CERTAIN 1991 THROUGH 2001 RANGER CERTAIN 1999 THROUGH 2001 EXPEDITION CERTAIN 1991 THROUGH 1994, AND 1997 MODEL YEAR F-SERIES CERTAIN 1991 THROUGH 1994 BRONCO NOTE: BOTH ORIGINAL EQUIPMENT AND REPLACEMENT TIRES ARE AFFECTED. Remedy: THE REPLACEMENT/REIMBURSEMENT PROGRAM FOR THIS CAMPAIGN EXPIRED ON MARCH 31, 2002. HOWEVER, CUSTOMERS CAN CONTACT FORD AT 1-877-917-3673 OR GO ON-LINE TO WWW.FORD.COM FOR POSSIBLE ASSISTANCE.
VEHICLE DESCRIPTION: MULTI-PURPOSE PASSENGER VEHICLES, EDDIE BAUER AND LIMITED EDITIONS. THE KEY-IN-IGNITION/DOOR OPEN WARNING CHIME MAY NOT FUNCTION WHEN THE DOOR IS OPENED. THIS DOES NOT FULLY COMPLY WITH FMVSS NO. 114, "THEFT PROTECTION." Remedy: DEALERS WILL INSTALL A JUMPER WIRE TO PROVIDE THE NECESSARY GROUND CIRCUIT IN THESE VEHICLES.
VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. THE SECONDARY HOOD LATCH MAY CORRODE AT THE LATCH PIVOT AND STICK IN THE OPEN POSITION. Remedy: DEALERS WILL INSTALL A SECONDARY HOOD LATCH WITH COMPONENTS THAT ARE COATED PRIOR TO ASSEMBLY FOR IMPROVED LATCH PIVOT CORROSION PROTECTION.
VEHICLE DESCRIPTION: MULTI-PURPOSE PASSENGER VEHICLES EQUIPPED WITH 4.0L SINGLE OVERHEAD CAM ENGINES. THE ENGINE FUEL LINES CAN BE DAMAGED IF THE VEHICLE IS JUMP STARTED AND THE GROUND CABLE IS ATTACHED TO THE FUEL LINE BRACKET THAT IS LOCATED NEAR THE BATTERY. SINCE THE BRACKET IS NOT GROUNDED, THE STAINLESS STEEL FUEL LINE BRAID COULD ACT AS A GROUND POTENTIALLY OVERHEATING THE PTFE INNER LINER OF THE FUEL LINE RESULTING IN DAMAGE TO THE FUEL LINE. Remedy: DEALERS WILL INSTALL A WARNING LABEL ON THE FUEL LINE BRACKET ADVISING OWNERS NOT TO USE IT FOR A JUMP START GROUND. ALSO A REVISED BOLT WILL BE INSTALLED IN THE ALTERNATOR BRACKET TO PROVIDE A CONVENIENT JUMP START GROUND LOCATION.
VEHICLE DESCRIPTION: CERTAIN 1997-1999 RHD EXPLORER EQUIPPED WITH 4.0L OHV/SOHC ENGINES AND CRUISE CONTROL BUILT FROM MAY 29, 1996 THROUGH MARCH 4, 1999; 1998-1999 EXPLORER/MOUNTAINEERS EQUIPPED WITH 4.0L OHV/SOHC OR 5.0L ENGINES OR 1998-1999 RANGERS EQUIPPED WITH 2.5L, 3.0L FFV/EFI OR 4.0L ENGINES AND CRUISE CONTROL BUILT FROM JANUARY 5, 1998 THROUGH MARCH 4, 1999; 1998-1999 MUSTANGS EQUIPPED WITH 3.8L, 4.6L 2-VALVE OR 4-VALVE ENGINES AND CRUISE CONTROL BUILT FROM MARCH 2, 1998 THROUGH MARCH 4, 1999; 1999 F250/F350/F450/F550 (OVER 8,500 LBS.) TRUCKS EQUIPPED WITH 5.4L OR 6.8L ENGINES AND CRUISE CONTROL BUILT FROM MARCH 2, 1998 THROUGH MARCH 4, 1999; AND 1999 F-53 STRIPPED CHASSIS EQUIPPED WITH 5.4L OR 6.8L ENGINES AND CRUISE CONTROL BUILT FROM MARCH 2, 1998 THROUGH MARCH 4, 1999. A CRUISE CONTROL CABLE CAN INTERFERE WITH THE SPEED CONTROL SERVO PULLEY AND NOT ALLOW THE THROTTLE TO RETURN TO IDLE WHEN DISENGAGING THE CRUISE CONTROL. Remedy: DEALERS WILL REPLACE THE CRUISE CONTROL CABLES. AT THE PRESENT TIME, THE REPLACEMENT CABLES ARE NOT AVAILABLE. CUSTOMERS ARE BEING ADVISED NOT TO USE THE CRUISE CONTROL SYSTEM UNTIL A REPLACEMENT CAN BE MADE.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Issue: This recall is for aftermarket replacement rear window glass produced by Vitro Automotriz. Certain rear window glass may not have been properly tempered. If the window breaks, the glass may separate into large pieces instead of very small ones. Note: This is a voluntary recall that is not being conducted under the requirements of the Motor Vehicle Safety Act. Safety Risk: Glass that breaks in to large pieces could create a risk of injury. Corrective Actions: The company will notify consumers by mail and instruct them to inspect the designation code marked on the rear window glass. Products affected by this recall have the designation “DOT 287” along with the lettering “VMR” (Replacement Market) and a date code that is before July 2019. This information is printed on the bottom corner of the glass. Consumers should contact Vitro's customer service at 1-412-995-6457 or argbacklites@vitro.com to arrange for replacement of the glass.
On certain vehicles, the speed control deactivation switch may overheat, smoke, or burn, potentially resulting in an underhood fire. The condition may occur either when the vehicle is parked or when it is in operation. Correction: Dealers will install a new switch or fused wiring harness. Note: This is an expansion of recall 2005028 (05S28) for vehicles not previously included in the campaign.
On certain Explorer, Explorer Sport and Explorer Sport Trac vehicles, the upper bolt on the driver's high back seat that attaches the seat recliner mechanism to the seat back frame could fracture. If this happens, the seat back may recline until it makes contact with an object behind the seat, such as the 2nd row seat cushion. The occupant could potentially lose contact with the steering wheel or foot pedals during such an event. Correction: Dealer will replace the driver's seat upper bolt.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Crash-test ratings from NHTSA's New Car Assessment Program.
Source: NHTSA (US Department of Transportation) · US public domain
On certain vehicles, the speed control deactivation switch may overheat, smoke, or burn, potentially resulting in an underhood fire. The condition may occur either when the vehicle is parked or when it is in operation. Correction: Initially as an interim repair, owners will be instructed to return their vehicles to their dealers to have the speed control deactivation switch disconnected. As soon as replacement parts are available, owners will be instructed to return to the dealers for installation of a new switch or fused wiring harness.
On certain Explorer, Explorer Sport and Explorer Sport Trac vehicles, the upper bolt on the driver's high back seat that attaches the seat recliner mechanism to the seat back frame could fracture. If this happens, the seat back may recline until it makes contact with an object behind the seat, such as the 2nd row seat cushion. The occupant could potentially lose contact with the steering wheel or foot pedals during such an event. Correction: Dealer will replace the driver's seat upper bolt.
On certain vehicles, the original throttle bodies installed allowed a gap between the plate and bore to be built with reduced clearances or too narrow. This reduced clearance allowed the thin film of engine deposits normally present in the throttle body to contact or bridge the gap. If the engine deposits bridged the gap between the throttle plate and bore and hardened, on the initial application of the accelerator pedal after the engine has cooled, the operator would need to apply additional force to the accelerator pedal to break the bridge. This could result in the throttle body sticking closed. Correction: Original throttle bodies will be replaced on affected vehicles.
On certain vehicles, the secondary hood latch may corrode at the latch pivot and stick in the open position. If this occurs and the primary hood latch is either not engaged or is released, a hood fly-up may occur. If this occurs, the driver's forward vision could be obstructed, which could result in a collision. Correction: Dealers will install a secondary hood latch with components that are coated prior to assembly for improved latch pivot corrosion protection.
On certain vehicles, the speed control cable may interfere with the speed control servo pulley and not allow the throttle to return to idle when disengaging the speed control. If the speed control is used and this condition is present, a stuck throttle could result, which could potentially cause an accident. By not using speed control, this condition will not occur. Correction: Vehicles will be inspected and, if required, speed control cable will be replaced.
THE ENGINE FUEL LINES MAY BE DAMAGED IF THE FUEL LINE BRACKET NEAR THE BATTERY IS USED AS A GROUND WHILE JUMP STARTING THE VEHICLE. SINCE THE BRACKET IS NOT GROUNDED, THE STAINLESS STEEL FUEL LINE BRAID WILL ACT AS A GROUND. THIS COULD OVERHEAT THE PTFE INNER LINER OF THE FUEL LINE AND RESULT IN DAMAGE TO THE FUEL LINE. THIS COULD CAUSE FUEL LEAKAGE AND IN THE PRESENCE OF AN IGNITION SOURCE, A FIRE COULD OCCUR. CORRECTION: A LABEL WILL INSTALLED ADVISING OWNERS NOT TO USE THE FUEL LINE BRACKET AS A JUMP START GROUND. A REVISED BOLT WILL BE INSTALLED IN THE ALTERNATOR BRACKET TO PROVIDE A CONVENIENT JUMP START GROUND.
NOTE: EDDIE BAUER AND LIMITED EDITIONS. THESE VEHICLES MAY NOT COMPLY WITH C.M.V.S.S. 114 - LOCKING SYSTEM. THE KEY-IN-IGNITION/DOOR OPEN WARNING CHIME IN THESE VEHICLES MAY NOT FUNCTION WHEN THE DOOR IS OPENED. THE CLOCKSPRING FOR VEHICLES WITH REDUNDANT STEERING CONTROLS DOES NOT CONTAIN A GROUNDING CIRCUIT FOR THE KEY-IN-IGNITION CIRCUITRY. CORRECTION: A CLOCKSPRING GROUND CIRCUIT WILL BE INSTALLED ON AFFECTED VEHICLES.