Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1998 Freightliner Century, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS. THE TIE ROD ENDS CAN FRACTURE DUE TO LOW STRESS, HIGH CYCLE, REVERSED BENDING FATIGUE RESULTING FROM A SYSTEM RESONANCE. Remedy: DEALERS WILL REPLACE THE TIE ROD ENDS AND TUBE ASSEMBLY.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS. THE OUTBOARD BEARING ON THE STEERING AXLE HUBS CAN FAIL DUE TO WATER INTRUSION THROUGH A HUBCAP VENT. Remedy: DEALERS WILL REMOVE THE HUBCAP AND INSPECT FOR WATER INTRUSION AND CORROSION. THE HUB AND BEARING ASSEMBLY WILL BE REPLACED IF THERE IS EVIDENCE OF CORROSION. A NON-VENTED HUBCAP WILL BE INSTALLED.
ON CERTAIN TRUCKS EQUIPPED WITH TRUCK HUB UNITS MANUFACTURED BY SKF EXCLUSIVELY FOR USE ON ARVINMERITOR'S FF98X SERIES NON-DRIVE STEER AXLES, THE HUB UNIT BEARINGS CAN WEAR PREMATURELY. Remedy: DEALERS WILL REPLACE BOTH FRONT HUBS. OWNER NOTIFICATION IS EXPECTED TO BEGIN ON OR BEFORE SEPTEMBER 20, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FREIGHTLINER AT 1-800-547-0712.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS AND SCHOOL BUS CHASSIS BUILT WITH BENDIX AIR ABS WITH AN EC-17 1030R ELECTRONIC CONTROL UNIT (ECU), THERE HAVE BEEN REPORTS OF UNWANTED ABS ACTIVATION AT LOW SPEEDS CAUSED BY 1) CHAFED ABS WHEEL SPEED SENSOR WIRES ON ROTATING PARTS OR 2) A DAMAGED COMPONENT AT THE WHEEL END THAT GENERATES A CERTAIN TYPE OF ERRATIC SENSOR SIGNAL. Remedy: DEALERS WILL REPLACE THE ABS ECU.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH MERITOR INTERAXLE DRIVELINE U-JOINTS. DEFLECTOR RINGS, A PART OF THE SYSTEM TO SEAL THE U-JOINTS FROM CONTAMINATES, ARE LOOSE. THIS ALLOWS WATER TO ENTER THE U-JOINT BEARING AREA RESULT IN DILUTION OF THE LUBRICANT, OXIDATION OF THE BEARING AND SEAL SURFACES, AND LOSS OF LUBRICANT. Remedy: DEALERS WILL REPLACE THE U-JOINTS WITH THE CURRENT DESIGN U-JOINTS.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain vehicles, manufacturing defects in the front axle unitized hubs may cause premature spalling of the wheel bearings. This condition will lead to eventual breakdown of the bearing and potential loss of vehicle control amidst the presence of warning signals such as activation of ABS warning light, steering wheel vibration, brake drag, noise and vehicle pull. Correction: Dealer will replace both front wheel hubs.
The TRW tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness. This can lead to premature wear out and a possible separation of the ball stud from the socket and loss of steering control. Correction: All affected tie rods and drag links with different design ends will be replaced.
On certain vehicles, the Bendix ABS ECU misinterprets certain signals from wheel ends which can result in the temporary loss of braking capability on one or more wheel positions for several seconds. This response results from either an ABS cable that has chafed through the insulation and contacted a rotating part or a misaligned tone ring that has been damaged by contacting other components. Correction: ABS ECU will be replaced with a new ECU with upgraded software capable of detecting and properly responding to erroneous signals.
On certain vehicles, the tie rod ends may fracture due to low stress, high cycle, reversed bending fatigue resulting from a system resonance. This condition could result in loss of steering control. Correction: The tie rod ends and tube assembly will be replaced with tie rod ends of a higher strength material specification.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
THE U-JOINT DEFLECTOR RINGS MAY BE LOOSE, ALLOWING WATER TO ENTER THE U-JOINT BEARING AREA RESULTING IN DILUTION OF THE LUBRICANT, OXIDATION OF BEARING AND SEAL SURFACES, AND LOSS OF LUBRICANT. THIS COULD RESULT IN SEPARATION OF THE INTERAXLE DRIVELINE. CORRECTION: VEHICLES WILL BE INSPECTED FOR LOOSE DEFLECTOR RINGS, AND IF LOOSE, THE U-JOINT WILL BE REPLACED WITH A NEW DESIGN VERSION.