Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1998 Freightliner FLD, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
CERTAIN HEAVY DUTY TRUCKS CONVERTED FROM SLEEPERCABS TO DAY CABS AND EQUIPPED WITH A DETROIT DIESEL OPTIMIZED IDLE SYSTEM. THE IDLE SYSTEM WAS NOT COMPLETELY DISABLED IN THE CAB CONVERSION PROCESS. Remedy: DEALERS WILL COMPLETELY DISABLE THE OPTIMIZED IDLE SYSTEM. OWNER NOTIFICATION BEGAN APRIL 3, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FREIGHTLINER AT 1-800-547-0712.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS. THE OUTBOARD BEARING ON THE STEERING AXLE HUBS CAN FAIL DUE TO WATER INTRUSION THROUGH A HUBCAP VENT. Remedy: DEALERS WILL REMOVE THE HUBCAP AND INSPECT FOR WATER INTRUSION AND CORROSION. THE HUB AND BEARING ASSEMBLY WILL BE REPLACED IF THERE IS EVIDENCE OF CORROSION. A NON-VENTED HUBCAP WILL BE INSTALLED.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH CATERPILLAR ENGINES AND EATON AUTOSHIFT TRANSMISSIONS. THE ENGINES CAN STALL BECAUSE OF SOFTWARE PROBLEMS. Remedy: CATERPILLAR IS CONDUCTING THE OWNER NOTIFICATION AND REMEDY OF THIS RECALL. DEALERS WILL UPDATE THESE ENGINES WITH SOFTWARE CHANGES.
ON CERTAIN TRUCKS EQUIPPED WITH TRUCK HUB UNITS MANUFACTURED BY SKF EXCLUSIVELY FOR USE ON ARVINMERITOR'S FF98X SERIES NON-DRIVE STEER AXLES, THE HUB UNIT BEARINGS CAN WEAR PREMATURELY. Remedy: DEALERS WILL REPLACE BOTH FRONT HUBS. OWNER NOTIFICATION IS EXPECTED TO BEGIN ON OR BEFORE SEPTEMBER 20, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FREIGHTLINER AT 1-800-547-0712.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS AND SCHOOL BUS CHASSIS BUILT WITH BENDIX AIR ABS WITH AN EC-17 1030R ELECTRONIC CONTROL UNIT (ECU), THERE HAVE BEEN REPORTS OF UNWANTED ABS ACTIVATION AT LOW SPEEDS CAUSED BY 1) CHAFED ABS WHEEL SPEED SENSOR WIRES ON ROTATING PARTS OR 2) A DAMAGED COMPONENT AT THE WHEEL END THAT GENERATES A CERTAIN TYPE OF ERRATIC SENSOR SIGNAL. Remedy: DEALERS WILL REPLACE THE ABS ECU.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain vehicles, manufacturing defects in the front axle unitized hubs may cause premature spalling of the wheel bearings. This condition will lead to eventual breakdown of the bearing and potential loss of vehicle control amidst the presence of warning signals such as activation of ABS warning light, steering wheel vibration, brake drag, noise and vehicle pull. Correction: Dealer will replace both front wheel hubs.
The TRW tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness. This can lead to premature wear out and a possible separation of the ball stud from the socket and loss of steering control. Correction: All affected tie rods and drag links with different design ends will be replaced.
On certain vehicles, the Bendix ABS ECU misinterprets certain signals from wheel ends which can result in the temporary loss of braking capability on one or more wheel positions for several seconds. This response results from either an ABS cable that has chafed through the insulation and contacted a rotating part or a misaligned tone ring that has been damaged by contacting other components. Correction: ABS ECU will be replaced with a new ECU with upgraded software capable of detecting and properly responding to erroneous signals.
On certain vehicles equipped with Caterpillar engines, EATON Auto Shift transmissions and an Auto Retarder in Cruise option, if the driver initiates a downshift when the cruise control is being used and the Auto Retarder in Cruise is on, the retarder may stall the engine when the transmission shifts into neutral without prior warning. This is due to incorrect programming of the Electronic Control Module. Correction: Auto Retarder in Cruise will be disabled. When new software is available, the electronic engines will be reprogrammed to eliminate the problem.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain