Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1998 Lincoln Navigator, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS. Remedy: SABERSPORT WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON MAY 11, 2009. OWNERS MAY CONTACT SABERSPORT AT 1-909-598-7589.
ON CERTAIN PICKUP TRUCKS AND SPORT UTILITY VEHICLES EQUIPPED WITH SPEED CONTROL, THE SPEED CONTROL DEACTIVATION SWITCH MAY OVERHEAT, SMOKE, OR BURN. Remedy: BY LETTER DATED SEPTEMBER 12, 2005, OWNERS WERE INSTRUCTED TO RETURN THEIR VEHICLES TO THEIR DEALERS TO HAVE THE SPEED CONTROL DEACTIVATION SWITCH DISCONNECTED. OWNERS WHO HAVE HAD THEIR SPEED CONTROL DEACTIVATED ARE BEING NOTIFIED THAT PARTS WILL BE AVAILABLE AND ADVISED TO MAKE AN APPOINTMENT TO RECONNECT THE SPEED CONTROL BEGINNING IN FEBRUARY 2006. OWNERS WHO DID NOT HAVE THEIR SPEED CONTROL DEACTIVATED ARE BEING NOTIFIED TO HAVE THEIR SYSTEM REMEDIED BEGINNING IN FEBRUARY 2006. OWNERS ARE URGED TO AVAIL THEMSELVES OF THE FREE DISCONNECT SERVICE AS SOON AS POSSIBLE BECAUSE OF THE SIGNIFICANT RISK OF FIRE. OWNERS MAY CONTACT FORD AT 1-800-392-3673. (NOTE: ALSO SEE RECALLS 05V017 AND 06V286)
VEHICLE DESCRIPTION: MULTI-PURPOSE VEHICLES. THE TRAILER HITCH ASSEMBLY TO THE FRAME ATTACHING BOLTS COULD LOSE THE CLAMP LOAD. Remedy: DEALERS WILL REPLACE THE TRAILER HITCH MOUNTING BOLTS AND NUT PLATES.
VEHICLE DESCRIPTION: MULTI-PURPOSE VEHICLES AND LIGHT DUTY PICKUP TRUCKS. THE LUG NUTS ON THESE VEHICLES MAY NOT CREATE SUFFICIENT CLAMP LOAD ALLOWING WHEEL MOVEMENT IN RELATION TO THE HUB/ROTOR MOUNTING SURFACE. Remedy: OWNERS OF THESE VEHICLES WILL BE RECEIVING TWO NOTIFICATIONS. THE FIRST NOTIFICATION, WHICH BEGAN IN MAY 1998, WILL PROVIDE AN INTERIM REPAIR PROCEDURE UNTIL PARTS BECOME AVAILABLE. THIS INTERIM PROCEDURE CAN BE COMPLETED BY OWNERS OR THEIR DEALERS. IT SPECIFIES THAT THE LUG NUT TORQUE MUST BE VERIFIED TO BE 100 LBS. THEN THE LUG NUTS NEED TO BE TIGHTENED AN ADDITIONAL 1/8 TO 1/4 TURN MORE. THERE WILL BE A SECOND OWNER NOTIFICATION, WHICH IS EXPECTED TO BEGIN JULY 20, 1998, UNDER WHICH DEALERS WILL INSPECT THE WHEEL STUDS AND REPLACE THE WHEEL LUG NUTS.
VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS AND MULTI-PURPOSE PASSENGER VEHICLES. IF THE AUTOMATIC TRANSMISSION SHIFT CABLE ASSEMBLY WAS NOT FULLY ATTACHED TO THE STEERING COLUMN BRACKET, THE SHIFT CABLE ASSEMBLY CAN COME OUT OF THE BRACKET. THE VEHICLE OPERATOR WOULD THEN NOT BE ABLE TO SHIFT THE TRANSMISSION FROM ONE OF THE DRIVE GEAR POSITIONS INTO THE PARK POSITION EVEN THOUGH THE GEAR SHIFT SELECTOR WOULD INDICATE "PARK." Remedy: DEALERS WILL MAKE THE PROPER ATTACHMENT OF THE TRANSMISSION SHIFT CONTROL CABLE TO THE STEERING COLUMN BRACKET AND ADD A TIE STRAP TO THAT CONNECTION.
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE TEXT AND/OR GRAPHICS FOR THE VEHICLE HEADLAMP AIMING INSTRUCTIONS PROVIDED IN THE OWNER GUIDES ARE NOT SUFFICIENTLY CLEAR. THIS DOES NOT MEET THE REQUIREMENTS OF FMVSS NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." Remedy: OWNER GUIDES CONTAINING REVISED AIMING INSTRUCTIONS WILL BE MAILED TO OWNERS OF THESE VEHICLES.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain vehicles, the speed control deactivation switch may overheat, smoke, or burn, potentially resulting in an underhood fire. The condition may occur either when the vehicle is parked or when it is in operation. Correction: Initially as an interim repair, owners will be instructed to return their vehicles to their dealers to have the speed control deactivation switch disconnected. As soon as replacement parts are available, owners will be instructed to return to the dealers for installation of a new switch or fused wiring harness.
On certain vehicles, Ford has issued a scheduled maintenance guide update which specifies that every 20 000 kms, the steering linkage, which includes tie-rod ends, should be inspected. The vehicle owner is asked to place the tie-rod end inspection procedure supplied with this maintenance guide update in the vehicle's glove box for reference and safekeeping. The vehicle owner is to provide the inspection procedure to their repair facility to help properly identify worn tie-rod ends. Performing the vehicle scheduled maintenance, including maintenance inspections, is the responsibility of the vehicle owner. Failure to replace worn tie-rod ends may eventually result in a tie-rod end separation that could adversely affect steering control. If the inspection reveals that a tie-rod end is worn and must be replaced, the repair will be at the owner's expense unless the vehicle is still covered by the basic vehicle warranty, or has an extended service plan coverage that includes these components.
On certain vehicles, the trailer hitch assembly attachment bolts may lose clamp load. If the operator does not notice the condition due to rattle or other looseness of the trailer hitch assembly, there is a potential for the trailer hitch to separate from the vehicle. Correction: Trailer hitch mounting bolts and nut plates will be replaced with higher strength mounting bolts and nut plates installed at a higher torque and including an adhesive patch.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Crash-test ratings from NHTSA's New Car Assessment Program.
Source: NHTSA (US Department of Transportation) · US public domain
ON CERTAIN VEHICLES, THE LUG NUTS ON THESE VEHICLES MAY NOT CREATE SUFFICIENT CLAMP LOAD ALLOWING WHEEL MOVEMENT IN RELATION TO THE HUB/ROTOR MOUNTING SURFACE. THIS COULD RESULT IN LOOSENING OF THE LUG NUTS, STUD FATIGUE FAILURE, AND THE POTENTIAL FOR A WHEEL TO SEPARATE FROM THE VEHICLE. CORRECTION: WHEEL STUDS WILL BE INSPECTED AND WHEEL LUG NUTS WILL BE REPLACED WITH REVISED VERSIONS.
THESE VEHICLES DO NOT COMPLY WITH C.M.V.S.S. 108 - LIGHTING SYSTEM AND RETROREFLECTIVE DEVICES. THE HEADLIGHT AIMING INSTRUCTIONS PROVIDED IN THE OWNER GUIDES ARE NOT SUFFICIENTLY CLEAR. CORRECTION: REVISED OWNER GUIDES WILL BE MAILED TO OWNERS.
ON CERTAIN VEHICLES, THE AUTOMATIC SHIFT CABLE ASSEMBLY MAY NOT BE PROPERLY SEATED AND COULD SEPARATE FROM THE STEERING COLUMN BRACKET. SHOULD THIS OCCUR, THE OPERATOR WOULD NOT BE ABLE TO SHIFT THE TRANSMISSION FROM ONE OF THE DRIVE GEAR POSITION INTO THE PARK POSITION EVEN THOUGH THE GEAR SELECTOR WOULD INDICATE "PARK". THIS COULD RESULT IN UNINTENDED VEHICLE MOVEMENT IF THE PARKING BRAKE IS NOT SET. CORRECTION: SHIFT CONTROL CABLE WILL BE PROPERLY ATTACHED TO THE STEERING COLUMN BRACKET AND A TIE STRAP WILL BE ADDED TO THAT CONNECTION AS A REDUNDANT MEASURE TO SECURE THE ATTACHMENT.