Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1999 Chevrolet Silverado, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
K2 MOTOR IS RECALLING 1,921 AFTERMARKET HEADLAMPS OF VARIOUS MODELS SOLD FOR USE ON THE ABOVE LISTED VEHICLES. THESE HEADLAMPS ARE MISSING THE AMBER SIDE REFLEX REFLECTOR WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." Remedy: K2 MOTOR WILL NOTIFY OWNERS AND OFFER A FULL REFUND. THE RECALL BEGAN ON DECEMEBER 17, 2008. OWNERS MAY CONTACT K2 MOTOR AT 1-909-839-2992.
CERTAIN AAI MOTORSPORTS COMBINATION LAMPS SOLD AS REPLACEMENT LAMPS FOR USE ON THE ABOVE LIST PASSENGER VEHICLES. COMBINATION LAMPS NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." Remedy: AAI MOTORSPORTS WILL NOTIFY OWNERS AND REPLACE THE LAMPS FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 1, 2006. OWNERS MAY CONTACT AAI MOTORSPORTS AT 909-923-9188.
SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS. Remedy: SABERSPORT WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON MAY 11, 2009. OWNERS MAY CONTACT SABERSPORT AT 1-909-598-7589.
CERTAIN MAXZONE HEADLIGHT ASSEMBLIES, DEPO BRAND, P/NOS. 332-1182L-AS AND 332-1182R-AS, SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR 1999-2000 CHEVROLET SILVERADOS. THESE HEADLAMPS FAIL TO CONFORM TO THE PHOTOMETRIC REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT. Remedy: MAXZONE WILL NOTIFY OWNERS AND OFFER FOR REIMBURSEMENT ANY NONCOMPLIANT HEADLIGHTS. THE RECALL BEGAN ON JULY 10, 2006. OWNERS MAY CONTACT MAXZONE AT 909-822-3288.
DOPE, INC. IS RECALLING 42,540 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS. Remedy: DOPE, INC. WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON JULY 28, 2009. OWNERS MAY CONTACT DOPE, INC. AT 1-626-272-1798.
CERTAIN GUIDE REPLACEMENT HEADLAMPS, P/NOS. 16526133 AND 16526134, MANUFACTURED FROM JANUARY 1 TO JULY 11, 2006, SOLD FOR USE ON MY 1999-2002 CHEVROLET SILVERADO PICKUP TRUCKS. THE HEADLAMP FAIL TO COMPLY WITH THE PHOTOMETRY REQUIREMENT OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT. Remedy: GUIDE CORPORATION WILL NOTIFY OWNERS AND REPLACE THE HEADLAMPS FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 31, 2006. OWNERS MAY CONTACT GUIDE AT 248-874-0355.
CERTAIN PRO-A MOTORS CORNER LAMPS, TURN SIGNALS, AND HEADLIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON CERTAIN PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT. Remedy: PRO-A MOTORS WILL NOTIFY OWNERS AND OFFER TO REPURCHASE THE LAMPS. THE RECALL BEGAN ON APRIL 3, 2006. OWNERS MAY CONTACT PRO-A MOTORS AT 323-838-2988.
CERTAIN PICKUP TRUCKS HAVE GALVANIZED-BRAIDED-STEEL TAILGATE SUPPORT CABLES USED TO SUPPORT THE TAILGATE IN THE FULL OPEN (HORIZONTAL) POSITION. OVER TIME THESE CABLES CAN CORRODE AND FRACTURE WHEN LOADS ARE APPLIED TO THEM. Remedy: DEALERS WILL REPLACE THE GALVANIZED SUPPORT CABLES WITH STAINLESS STEEL SUPPORT CABLES. IN ADDITION, DEALERS ARE TO INSPECT THE TAILGATE HINGE AND REPLACE IT, IF NECESSARY. THE RECALL IS EXPECTED TO BEGIN DURING APRIL 2006. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438 OR GMC AT 1-866-996-9463.
CERTAIN CEQUENT 90 DEGREE 7-WAY RIGHT ANGLE ADAPTORS SOLD BY DISTRIBUTORS IN TOW PACKAGES FOR AFTERMARKET SALES TO TOW 5TH WHEEL RV TRAVEL TRAILERS. DUE TO INCORRECT WIRING OF THE HARNESS, THE TRAILER LIGHTS MAY NOT OPERATE PROPERLY. Remedy: ALL OF THE DEFECTIVE TOW PACKAGES ARE STILL AT THE DISTRIBUTOR LEVEL AND HAVE NOT BEEN SOLD TO ANY CONSUMERS.
CERTAIN EAGLE EYES REPLACEMENT HEADLAMPS, MODEL NOS. GM159-B001L AND GM159-B001R, SOLD FOR USE ON 1999-2002 CHEVROLET SILVERADO MODEL VEHICLES. THE HEADLAMPS FAIL TO CONFORM TO THE PHOTOMETRIC REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT. Remedy: SABRY LEE WILL NOTIFY OWNERS AND ISSUE FULL CREDIT. THE RECALL BEGAN ON MAY 10, 2006. OWNERS MAY CONTACT SABRY LEE AT 1-866-467-2279.
CERTAIN FEDERAL-MOGUL REPLACEMENT WHEEL HUB ASSEMBLIES WITH THE BRAND NAMES: NATIONAL, CARQUEST P/NOS. 515020, 515021, 515025, 515053, 515054, 515059, AND 515060, SHIPPED BETWEEN JANUARY 23, 2006, AND DECEMBER 20, 2007, SOLD FOR LIGHT DUTY AND MEDIUM DUTY TRUCKS. THE INBOARD RETENTION NUT USED TO MAINTAIN HUB BEARING ASSEMBLY CAN LOOSEN RESULTING IN AN ABS LIGHT INDICATION, NOISE, AND/OR WHEEL SEPARATION. Remedy: FEDERAL-MOGUL WILL NOTIFY CUSTOMERS AND WILL REPLACE THE HUB ASSEMBLY FREE OF CHARGE. THE RECALL BEGAN ON FEBRUARY 7, 2008. OWNERS CAN CONTACT FEDERAL-MOGUL TOLL-FREE AT 877-489-6659.
ON CERTAIN PICKUP TRUCKS EQUIPPED WITH MANUAL TRANSMISSIONS AND BUILT WITH EITHER PBR PARKING BRAKE SYSTEMS OR TRW PARKING BRAKE SYSTEMS, THE PARKING BRAKE FRICTION LININGS MAY WEAR TO AN EXTENT WHERE THE PARKING BRAKE CAN BECOME INEFFECTIVE IN IMMOBILIZING A PARKED VEHICLE. Remedy: DEALERS WILL INSTALL A LOW-FORCE SPRING CLIP RETAINER FOR VEHICLES EQUIPPED WITH A PBR PARKING BRAKE SYSTEM. ON VEHICLES EQUIPPED WITH THE TRW PARKING BRAKE SYSTEM, DEALERS WILL INSTALL A REDESIGNED PARKING BRAKE CABLE ASSEMBLY. THE RECALL BEGAN ON JULY 29, 2005. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438 OR GMC AT 1-866-996-9463.
VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS AND SPORT UTILITY VEHICLES. SOME OF THESE VEHICLES HAVE A CLEARANCE CONDITION BETWEEN THE FRONT RIGHT-HAND BRAKE PIPE AND THE BODY CROSS SILL THAT COULD DECREASE TO THE POINT OF ALLOWING CONTACT DURING THE LIFE OF THE VEHICLE. IF CONTACT OCCURS AND THE BRAKE PIPE BECOMES DAMAGED, IN HALF OF THE BRAKE SYSTEM THERE CAN BE A LOSS OF BRAKE FLUID AND PRESSURE. THE BRAKE WARNING LAMP WILL BE ACTIVATED WHEN THE BRAKE FLUID LEVEL REACHES THE INDICATOR LIMIT. Remedy: DEALERS WILL INSPECT THE FRONT RIGHT-HAND BRAKE PIPE FOR WEAR. IF THERE ARE SIGNS OF WEAR, THIS SECTION OF THE BRAKE PIPE WILL BE REPLACED WITH A NEW DESIGNED BRAKE PIPE SECTION. IF THERE ARE NOT SIGNS OF WEAR ON THE BRAKE PIPE, THE DEALER WILL INSTALL A SPACER CLIP TO ENSURE SUFFICIENT CLEARANCE BETWEEN THE BRAKE PIPE AND THE BODY CROSS SILL.
CERTAIN PICKUP TRUCKS AND SPORT UTILITY VEHICLES MAY EXPERIENCE UNWANTED ANTILOCK BRAKE SYSTEM (ABS) ACTIVATION. THIS CONDITION IS MORE LIKELY TO OCCUR IN ENVIRONMENTALLY CORROSIVE AREAS. THIS RECALL WILL BE LAUNCHED IN THE "SALT BELT" STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MARYLAND, MASSACHUSETTS, MAINE, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, WISCONSIN AND THE DISTRICT OF COLUMBIA ONLY. Remedy: DEALERS ARE TO REMOVE THE WHEEL SPEED SENSOR AND THOROUGHLY CLEAN THE WHEEL SPEED SENSOR MOUNTING SURFACE ON THE BEARING, APPLY RUST INHIBITOR TO THE CLEANED SURFACE, GREASE THE MOUNTING SURFACE, REINSTALL THE WHEEL SPEED SENSOR, AND CHECK THE PEAK-TO-PEAK OUTPUT VOLTAGE TO ENSURE THE WHEEL SPEED SIGNAL IS WITHIN SPECIFICATIONS. THE RECALL BEGAN SEPTEMBER 22, 2005. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438 OR GMC AT 1-866-996-9463.
AFTERMARKET PICKUP TRUCK OVER-THE-RAIL BEDLINERS MANUFACTURED FOR INSTALLATION ON 1999-2004 CHEVROLET SILVERADO AND GMC SIERRA PICKUP TRUCKS. THE TOGGLE WING ASSEMBLY USED TO ATTACH THE BEDLINER TO THE TRUCK BED IS NOT ENGAGING FULLY IN THE STAKE POCKET OF THE PICKUP TRUCK. Remedy: DURAKON WILL ISSUE A PRESS RELEASE IN ATTEMPT TO NOTIFY CUSTOMERS THAT COULD HAVE PURCHASED THE DEFECTIVE BEDLINER. IF YOU PURCHASED EITHER A DURAKON ALLSTAR OF PATRIOT OVERRAIL BEDLINER SINCE AUGUST 1, 2003, FOR 1999 TO 2004 CHEVROLET SILVERADO OR GMC SIERRA TRUCKS, OR PURCHASED ONE OF THESE PICKUP TRUCKS WITH EITHER BRAND BEDLINER ALREADY INSTALLED, YOU SHOULD RETURN TO AN AUTHORIZED DURAKON DEALER SO THAT THE BEDLINER CAN BE INSPECTED AND, IF NECESSARY, REPAIRED WITH A NEWLY DESIGNED TOGGLE WING FASTENING SYSTEM, OR IF REQUIRED, REPLACED WITH A NEW BEDLINER FREE OF CHARGE. PLEASE CALL THE DURAKON HOTLINE AT 1-800-933-4200 TO FIND THE NEAREST AUTHORIZED DURAKON DEALER.
THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH THE SAFETY ACT. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. VEHICLE DESCRIPTION: 1/2 TON LIGHT DUTY PICKUP TRUCKS. ON CERTAIN TRUCKS, FAILURE TO FOLLOW THE SERVICE PROCEDURE SET FORTH IN THE SERVICE MANUAL FOR REMOVAL OF THE FRONT BRAKE CALIPER CAN RESULT IN MOVEMENT OF THE FRONT BRAKE HOSE RELATIVE TO ITS KNUCKLE MOUNTING BRACKET. IF THIS MOVEMENT RESULTS IN INCREASED LENGTH BETWEEN THE BRACKET AND THE BANJO FITTING THAT ATTACHES TO THE BRAKE CALIPER, IT IS POSSIBLE FOR THE BRAKE HOSE TO COME IN CONTACT WITH THE WHEEL RIM. Remedy: DEALERS WILL ATTACH A NOTICE LABEL TO THE FRONT BRAKE HOSES STATING THAT THE CALIPERS MUST BE SUPPORTED WHEN REMOVED.
VEHICLE DESCRIPTION: EXTENDED CAB 4-WHEEL DRIVE PICKUP TRUCKS. SOME OF THESE VEHICLES HAVE A LOWER THAN SPECIFIED TORQUE ON ALL THREE OF THE STEERING GEAR TO FRAME ATTACHMENT BOLTS. THE BOLTS CAN LOOSEN OVER TIME ALLOWING THE STEERING GEAR TO MOVE. THIS LOOSENING CAN RESULT IN SOME UNRESPONSIVE STEERING FEEL AND SOME NOISE TO THE DRIVER. Remedy: DEALERS WILL RETORQUE THE STEERING GEAR TO FRAME BOLTS TO PROPER SPECIFICATIONS.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain vehicles, the galvanized-braided-steel tailgate support cables used to support the tailgate in the full open (horizontal) position can corrode over time and fracture when loads are applied to them. Tailgate support cable corrosion may not be visible because of the plastic sheathing covering the cable. If one cable fractured, the remaining cable may retain the tailgate in a horizontal position. If the remaining cable was weakened by corrosion, it could fracture within moments of the first cable fracture. If both cables fractured, the tailgate would suddenly drop approximately 10 degrees and strike the top surface of the rear bumper. If anyone is sitting or standing on the horizontal surface of the tailgate when both cables fracture, they could fall and be injured. On vehicles without a rear bumper, the tailgate may drop to a lower position. Correction: Dealers will replace the existing galvanized support cables with stainless steel support cables.
On certain 1999-2002 1500 series and 2001-2005 2500 & 3500 series trucks equipped with a manual transmission, the parking brake friction lining may wear to an extent where the parking brake can become ineffective in immobilizing a parked vehicle. Correction: Dealers will install a low-force spring clip retainer on vehicles equipped with PBR parking brake system and install a redesigned parking brake cable assembly on vehicle equipped with a TRW parking brake system.
Certain vehicles located in Ontario, Quebec, New Brunswick, Nova Scotia, Prince Edward Island, and Newfoundland & Labrador may experience unwanted Antilock Brake System (ABS) activation and increased stopping distances during low-speed brake application (less than 16 km/h and greater than 6 km/h). This condition does not set any ABS codes nor does it illuminate the ABS warning lamp. Correction: Dealers will remove the wheel speed sensor and thoroughly clean the wheel speed sensor mounting surface on the bearing, apply Zinc-X to the cleaned surface, grease the mounting surface, reinstall the wheel speed sensor, and check the output voltage to ensure the wheel speed signal is within specifications.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Certain vehicles: Light duty trucks. passenger vehicles and sport utility vehicles. Certain vehicles do not comply with the requirements of C.M.V.S.S. NO. 118, "POWER-OPERATED WINDOW, PARTITION & ROOF PANEL SYSTEMS." When the hazard flasher switch is used to turn the hazard flashers on or off, the retained accessory power (RAP) feature can be activated without a key in the ignition. Correction: There is no detrimental effect on vehicle safety so no corrective action is necessary.
On certain vehicles, the body cross sill may contact the front, right-hand brake pipe. This could eventually wear a hole in the brake pipe over the normal life of the vehicle and result in a brake fluid leak. This could ultimately result in a partial brake system failure and increased stopping distances. Correction: Dealers will inspect for brake pipe wear and replace worn section if necessary. A spacer clip will be installed to ensure adequate clearance.
Certain vehicles do not comply with the requirements of CMVSS 209 - Seat Belt Assemblies. These vehicles have front belt retractors that have higher G-force lock-up levels than those required by the standard. In addition, some retractors could have internal damage that could cause a "no-lock" condition. In the event of a vehicle crash, these conditions could result in increased occupant injury. Correction: Driver and passenger seat belt retractors will be replaced.
Certain vehicles equipped with 4.8 litre or 5.3 litre engines do not comply with the requirements of CMVSS 1103 - Exhaust Emissions. Engines may have been built with the wrong Linear Exhaust Gas Recirculation (LEGR) valve which could limit the required air flow rate. A failed valve could cause the vehicle to fail to meet applicable emissions standards. Correction: Vehicles will be inspected and LEGR valve will be replaced with a new valve where required.
Certain vehicles have lower than specified torque on all three of the steering gear to frame attachment bolts. In this condition, the bolts may loosen during the life of the vehicle. Relative movement of the steering gear to frame may wear and/or fatigue the attaching bolts to the point of breakage or the bolts backing out. This would result in steering gear separation and loss of steering control. Correction: Steering gear to frame bolts will be torqued to the proper specification.