Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1999 Ford Windstar, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
Ford Motor Company (Ford) is recalling certain model year 1998-2003 Windstar vehicles manufactured September 2, 1997, to July 3, 2003. The affected vehicles were previously remedied to safeguard against the rear axle cracking from corrosion, however, the remedy brackets may have been misinstalled. The incorrect bracket installations may limit the effectiveness of the service repair for NHTSA recalls 10V-385, 12V-193, and 12V-195. Remedy: Ford will notify owners, and dealers will inspect the brackets to verify their proper installation. If a bracket is found to have been misinstalled, the rear axle will be replaced. These repairs will be performed free of charge. The began on October 21, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S27.
FORD IS RECALLING CERTAIN MODEL YEAR 1998-2003 WINDSTAR VEHICLES MANUFACTURED FROM SEPTEMBER 1, 1997, THROUGH JULY 3, 2003, AND CURRENTLY REGISTERED OR ORIGINALLY SOLD IN VIRGINIA. OVER TIME, CORROSION CAN WEAKEN THE REAR AXLE MAKING IT SUSCEPTIBLE TO TORSIONAL STRESS. CORROSION AND STRESS CAN LEAD TO CRACKS WHICH, IF UNDETECTED, CAN INCREASE AND RESULT IN A COMPLETE FRACTURE OF THE AXLE. Remedy: FORD WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT AND INSTALL REAR AXLE REINFORCEMENT BRACKETS, OR REPLACE THE AXLES, AS NECESSARY. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE RECALL BEGAN ON JUNE 19, 2012. OWNERS MAY CONTACT FORD AT 1-866-436-7332.
FORD IS RECALLING CERTAIN MODEL YEAR 1998-2003 WINDSTAR VEHICLES MANUFACTURED FROM SEPTEMBER 1, 1997, THROUGH JULY 3, 2003, REGISTERED IN PUERTO RICO. DUE TO INCREASED STRESSES CAUSED BY HIGH CYCLES OF TORSIONAL LOADING, SPECIFIC TO THIS MARKET, THE REAR AXLE CAN CRACK. Remedy: FORD WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT AND INSTALL A REINFORCEMENT BRACKET ON THE REAR AXLE OR REPLACE THE AXLES, AS NECESSARY. THIS SERVICE WILL BE PROVIDED FREE OF CHARGE. THE RECALL BEGAN ON JUNE 1, 2012. OWNERS MAY CONTACT THE FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
FORD IS RECALLING CERTAIN MODEL YEAR 1999-2003 WINDSTAR VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATE OF VIRGINIA. CORROSION-RELATED FRACTURES OF THE FRONT LOWER CONTROL ARM REAR ATTACHING BRACKETS AND BODY MOUNT ATTACHMENTS MAY OCCUR. Remedy: DEALERS WILL INSPECT BOTH FRONT LOWER CONTROL ARM REAR ATTACHING BRACKETS AND BOTH BODY MOUNT ATTACHMENTS AT THE REAR OF THE FRONT SUBFRAME AND MAKE THE NECESSARY REPAIRS FREE OF CHARGE. THE RECALL BEGAN ON JUNE 18, 2012. OWNERS MAY CONTACT FORD AT 1-866-436-7332.
FORD IS RECALLING CERTAIN MODEL YEAR 1999-2003 WINDSTAR VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, THE DISTRICT OF COLUMBIA, ILLINOIS, INDIANA, IOWA, KENTUCKY, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, UTAH, VERMONT, WEST VIRGINIA, AND WISCONSIN. A SEPARATION OF A FRONT LOWER CONTROL ARM REAR ATTACHING BRACKET MAY RESULT IN A LOWER CONTROL ARM SEPARATION. A SEPARATION OF BOTH FRONT SUBFRAME REAR BODY MOUNTS MAY RESULT IN SEPARATION OF THE STEERING INTERMEDIATE SHAFT. Remedy: DEALERS WILL INSPECT BOTH FRONT LOWER CONTROL ARM REAR ATTACHING BRACKETS, AND BOTH BODY MOUNT ATTACHMENTS AT THE REAR OF THE FRONT SUBFRAME, AND MAKE THE NECESSARY REPAIRS FREE OF CHARGE. IF REPAIRS CANNOT BE MADE TO A VEHICLE, FORD WILL OFFER TO REPURCHASE THE VEHICLE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE FEBRUARY 21, 2011. OWNERS MAY CONTACT FORD AT 1-866-436-7332.
CERTAIN AFTERMARKET FUEL FILTERS SOLD UNDER THE PUROLATOR BRAND NAME, P/N F65277, SHIPPED FROM JANUARY 16 THROUGH JUNE 2, 2006, FOR USE ON THE ABOVE LISTED PASSENGER VEHICLES. DUE TO INCORRECT DESIGN, THE QUICK CONNECTORS MAY NOT FULLY SEAT WITH THE TUBE INTERFACE, EVEN THOUGH THE PERSON MAKING THE CONNECTION MAY BELIEVE THAT THE QUICK CONNECTOR IS FULLY ATTACHED. Remedy: UFI WILL NOTIFY OWNERS AND REPLACE THE FILTERS FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 4, 2006. OWNERS MAY CONTACT UFI FILTERS USA AT 800-230-5876.
FORD IS RECALLING CERTAIN MODEL YEAR 1998-2003 WINDSTAR VEHICLES MANUFACTURED FROM SEPTEMBER 1, 1997 THROUGH FEBRUARY 28, 2003 AND CURRENTLY REGISTERED OR ORIGINALLY SOLD IN CONNECTICUT, DELAWARE, DISTRICT OF COLUMBIA, ILLINOIS, INDIANA, IOWA, KENTUCKY, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN. AFTER MANY YEARS OF VEHICLE SERVICE IN THESE AREAS, CORROSION CAN WEAKEN THE REAR AXLE, MAKING IT SUSCEPTIBLE TO TORSIONAL STRESS. CORROSION AND STRESS CAN LEAD TO CRACKS WHICH IF UNDETECTED CAN PROPAGATE AND RESULT IN A COMPLETE FRACTURE OF THE AXLE. Remedy: AS PARTS BECOME AVAILABLE, DEALERS WILL INSPECT AND IF NECESSARY INSTALL THE REAR AXLE REINFORCEMENT BRACKETS FREE OF CHARGE. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON OCTOBER 20, 2010. OWNERS MAY CONTACT FORD AT 1-866-436-7332.
FORD IS RECALLING MODEL YEARS 1995-2003 WINDSTAR, 2000-2003 EXCURSION DIESEL, 1993-1997 AND 1999-2003 F-250 SD THROUGH F-550 SD DIESEL, 1992-2003 E-150 THROUGH E-550, 1995-2002 EXPLORER, 1997 AND 2002 MERCURY MOUNTAINEER, 1995-1997 AND 2001-2003 RANGER, AND 1994 F53 VEHICLES EQUIPPED WITH THE TEXAS INSTRUMENTS SPEED CONTROL DEACTIVATION SWITCH (SCDS). THE SCDS MAY LEAK INTERNALLY AND THEN OVERHEAT, SMOKE, OR BURN. Remedy: FORD WILL NOTIFY OWNERS THAT DEALERS WILL INSTALL A FUSED WIRING HARNESS IN LINE WITH THE SCDS. ON 1999-2003 WINDSTAR VEHICLES WITH A LEAKING SCDS, DEALERS WILL ALSO INSPECT THE ABS CONTROL MODULE CONNECTOR AND REPAIR AS NECESSARY. REPAIRS WILL BE COMPLETED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON OCTOBER 27, 2009. OWNERS MAY CONTACT FORD AT 1-888-222-2751.
VEHICLE DESCRIPTION: MINIVANS BUILT WITH INSTRUMENT CLUSTERS WITHOUT THE MESSAGE CENTER, FAIL TO COMPLY WITH THE REQUIREMENTS OF STANDARD NO. 118, "POWER-OPERATED WINDOW, PARTITION, AND ROOF PANEL SYSTEMS." THE POWER WINDOWS MAY BE OPERABLE AFTER THE IGNITION HAS BEEN TURNED TO THE "OFF" POSITION AND THE FRONT DOORS ARE OPENED. Remedy: DEALERS WILL RECONFIGURE THE VEHICLE FRONT END ELECTRONIC MODULE.
VEHICLE DESCRIPTION: MINI VANS EQUIPPED WITH AUXILIARY REAR AIR-CONDITIONING. IF THE AUXILIARY AIR-CONDITIONING BLOWER MOTOR STOPS TURNING WHILE IN THE MEDIUM-LOW BLOWER SPEED SETTING, THERE IS THE POTENTIAL THAT THE RESISTOR MAY BECOME HOT AND SMOKE. Remedy: DEALERS WILL INSTALL A JUMPER WIRE THAT WILL ENSURE THAT THE MEDIUM-LOW BLOWER SPEED SETTING IS PROTECTED BY THE THERMAL LIMITER. OWNER NOTIFICATION BEGAN AUGSUT 27, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-866-436-7332.
VEHICLE DESCRIPTION: MINI VANS. CONTAMINANTS SUCH AS WATER, SALT, AND WINDSHIELD WASHER SOLUTION CAN ENTER THE WIPER MOTOR COVER ASSEMBLY THROUGH PINHOLES ON THE EXTERIOR OF THE COVER THAT ARE USED IN THE MOLDING PROCESS. IN ADDITION, ON CERTAIN OF THE VEHICLES BUILT BETWEEN FEBRUARY AND AUGUST 2000, A SWITCH LOCATED IN THE PLASTIC COVER OF THE WIPER MOTOR GEAR CASE COULD MALFUNCTION AND OVERHEAT. EITHER OF THESE CONDITIONS COULD POTENTIALLY RESULT IN LOSS OF INTERMITTENT WIPER FUNCTION, LOSS OF WIPER PARK FUNCTION, COMPLETE LOSS OF WIPER FUNCTION, SMOKE, OR IGNITION OF THE PLASTIC COVER MATERIAL. CONTAMINANT ENTRY COULD ALSO RESULT IN UNINTENDED WIPER MOTOR OPERATION. Remedy: DEALERS WILL INSTALL A NEW WIPER COVER WITH IMPROVED SEALING AND WATER RESISTANCE. OWNER NOTIFICATION BEGAIN AUGUST 27, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-866-436-7332.
VEHICLE DESCRIPTION: MINIVANS. THE BRAKE FLUID MASTER CYLINDER IS RECESSED AND ORIENTED IN THE ENGINE COMPARTMENT SO THAT THE BRAKE FLUID WARNING STATEMENT EMBOSSED ON BOTH THE TOP OF THE FILLER CAP AND THE SIDE OF THE RESERVOIR BODY ARE NOT ENTIRELY VISIBLE BY DIRECT VIEW. THESE VEHICLES MAY NOT FULLY COMPLY WITH REQUIREMENTS OF FMVSS NO. 135, "PASSENGER CAR BRAKE SYSTEMS." Remedy: OWNERS WILL BE PROVIDED WITH NEW LABELS AND INSTALLATION INSTRUCTIONS.
THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH THE SAFETY ACT. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. VEHICLE DESCRIPTION: MINIVANS. THE OVERHEAD CONSOLE REAR RETAINING BRACKET CAN DEVELOP CRACKS AND SEPARATE, ALLOWING THE OVERHEAD CONSOLE TO BECOME LOOSE AND POSSIBLY FALL DOWN. Remedy: DEALERS WILL INSTALL A REDESIGNED RETAINING BRACKET IN THE SAME LOCATION AS THE ORIGINAL RETAINING BRACKET.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Issue: This recall is for aftermarket replacement rear window glass produced by Vitro Automotriz. Certain rear window glass may not have been properly tempered. If the window breaks, the glass may separate into large pieces instead of very small ones. Note: This is a voluntary recall that is not being conducted under the requirements of the Motor Vehicle Safety Act. Safety Risk: Glass that breaks in to large pieces could create a risk of injury. Corrective Actions: The company will notify consumers by mail and instruct them to inspect the designation code marked on the rear window glass. Products affected by this recall have the designation “DOT 287” along with the lettering “VMR” (Replacement Market) and a date code that is before July 2019. This information is printed on the bottom corner of the glass. Consumers should contact Vitro's customer service at 1-412-995-6457 or argbacklites@vitro.com to arrange for replacement of the glass.
On certain vehicles that had rear axle reinforcement brackets installed as part of safety recall 2010-284, the brackets may not have been installed properly, which could limit the effectiveness of the recall service repair in addressing the safety defect. Safety recall 2010-284 was conducted to address the risk that the combined effects of corrosion and stress can lead to a complete fracture of the axle. If the rear axle fractures, and the reinforcement brackets were not installed properly, vehicle handling may be adversely affected, increasing the risk of a crash. Correction: Dealers will inspect the rear axle reinforcement brackets that were installed as part of recall 2010-284. If one or both brackets are found improperly installed, the dealer will replace the rear axle.
On certain vehicles, the subframe may not have been properly e-coated during the manufacturing process. As a result, the subframe of vehicles originally sold, or currently registered, in areas of heavy road salt usage during winter months (Ontario, Quebec, New Brunswick, Nova Scotia, Prince Edward Island, and Newfoundland & Labrador), may rust over time, resulting in reduced durability of the front lower control arm rear attaching brackets and body mount attachments at the rear of the front subframe. A separation of a front lower control arm rear attaching bracket may result in a lower control arm separation. A separation of both front subframe rear body mounts may result in diminished vehicle directional control. Either condition could result in reduced steering control, which may lead to a crash causing property damage and/or personal injury. Correction: Dealers will inspect the front lower control arm rear attaching brackets and body mount attachments at the rear of the front subframe. If the front lower control arm rear attaching brackets are not cracked, perforated, or exhibiting significant metal loss, and if the front subframe at the rear body mount locations are not cracked with metal separation aft of the rear body mount, and if the front subframe is not cracked or perforated in the area between the rear body mount and the front lower control arm rear attaching bracket, the vehicle will be returned to its owner and the owner will be notified when to return for installation of reinforcement brackets.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Crash-test ratings from NHTSA's New Car Assessment Program.
Source: NHTSA (US Department of Transportation) · US public domain
On certain vehicles registered and operated in areas where road salt is used on the roadways during winter months for extended time periods (Ontario, Quebec, New Brunswick, Nova Scotia, Prince Edward Island and Newfoundland-Labrador), the rear axle may corrode and fracture. If the rear axle fractures, vehicle handling may be adversely affected, creating the risk of a crash. Correction: Dealers will install rear axle reinforcement brackets.
On certain vehicles, the speed control deactivation switch may overheat, smoke, or burn, potentially resulting in an underhood fire. The condition may occur either when the vehicle is parked or when it is in operation. Correction: Dealers will install a new switch or fused wiring harness. Note: This is an expansion of recall 2005028 (05S28) for vehicles not previously included in the campaign.
Certain vehicles do not comply with the requirements of CMVSS 120. The Standard specifies that for vehicles other than passenger cars, the label information shall display after each GAWR, the size designation and, if applicable, the type designation of rims. This information was inadvertently omitted from the compliance label affixed to the affected vehicles. Correction: Since this does not pose any safety risk, no corrective action is required.
On certain vehicles contaminants such as water, salt, and windshield washer solution can enter the wiper motor cover assembly through pinholes on the exterior of the cover that are used in the molding process. In addition, on certain of the vehicles built between February and August 2000, a switch located in the plastic cover of the wiper motor gear case could malfunction and overheat. Either of these conditions could potentially result in loss of intermittent wiper function, loss of wiper park function, complete loss of wiper function, smoke, or, potentially, ignition of the plastic cover material. Contaminant entry could also result in unintended wiper motor operation. Switch malfunction is most likely to occur when the intermittent setting of the wipers is being used, or when snow or ice obstructs the blades from returning to the "parked" position at the bottom of the windshield. Loss of visibility while driving increases the risk of a crash. Correction: Dealers will install a new wiper cover with improved sealing and water resistance.
On certain vehicles, if the auxiliary air-conditioning blower motor stops turning while in the medium-low blower speed setting, there is the potential that the resistor may become hot and smoke. The motor could potentially catch on fire. Correction: Dealers will install a jumper wire that will ensure that the medium-low blower speed setting is protected by the thermal limiter.
Certain vehicles do not comply with the requirements of CMVSS 118 - Power-operated windows, power-operated partitions and power-operated roof panels. If the key is placed in the "accessory" position and remains there for more than 70 seconds, the vehicle delayed accessory relay remains active when the ignition switch is moved to the "off" position, and the vehicle front door is opened. Under this condition, all accessories connected to the accessory relay, including the power windows, remain operable. Correction: Dealers will reconfigure the vehicle front end electronic module.
Certain vehicles do not comply with the requirements of CMVSS 105 - Hydraulic Brake Systems. The brake fluid warning statement embossed on the side of the brake fluid reservoir is not clearly visible by direct view. Correction: Warning labels, along with installation instructions and wipe materials will be sent to owners. Labels will be installed on the front of the reservoir where they will be entirely visible by direct view.