Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1999 Kenworth T600, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH AN OPTIONAL FIREWALL-MOUNTED CIRCUIT BREAKER. THE MAIN CAB POWER AND BATTERY POWER LEADS WERE ATTACHED INCORRECTLY. THIS CONDITION CAN RESULT IN THE MAIN CAB POWER BEING UNPROTECTED. Remedy: DEALERS WILL INSPECT AND CORRECT THE PROBLEM, AS NEEDED. OWNER NOTIFICATION BEGAN FEBRUARY 26, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT KENWORTH AT 1-425-828-5000.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH TRW TIE ROD ENDS ON CERTAIN MERITOR AXLES. THE TIE ROD AND DRAG LINK BALL STUD ENDS CONTAIN BEARINGS THAT ARE BELOW THE SPECIFIED CASE DEPTH AND/OR HARDNESS. Remedy: DEALERS WILL REMOVE AND REPLACE ALL AFFECTED TIE RODS AND DRAG LINKS WITH DIFFERENT DESIGNED ENDS. OWNER NOTIFICATION BEGAN OCTOBER 24, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT PETERBILT AT 1-940-591-4000 OR KENWORTH AT 1-425-828-5000.
ON CERTAIN TRUCKS EQUIPPED WITH TRUCK HUB UNITS MANUFACTURED BY SKF EXCLUSIVELY FOR USE ON ARVINMERITOR'S FF98X SERIES NON-DRIVE STEER AXLES, THE HUB UNIT BEARINGS CAN WEAR PREMATURELY. Remedy: DEALERS WILL REPLACE ALL FRONT AXLE HUBS. NOTIFICATION BEGAN JULY 16, 2003. THE MANUFACTURER HAS ADVISED US THAT PARTS WILL NOT BE AVAILABLE UNTIL SEPTEMBER 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITH A REASONABLE TIME SHOULD CONTACT PETERBILT AT 940-591-4201 OR KENWORTH 425-828-5440.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS. THE INSTALLATION OF THE ALUMINUM STEERING DRIVELINE EXCEEDS THE U-JOINT ANGLES SPECIFIED BY DANA, THE DRIVELINE MANUFACTURER. BY EXCEEDING THIS SPECIFICATION, THE U-JOINT COULD CONTACT AND CAUSE A STRESS RISER IN THE ALUMINUM DRIVE SHAFT. THIS CONTACT COULD CAUSE IN A NOTCH IN THE ALUMINUM DRIVEMENT, RESULTING IN A STRESS RISER IN THE SHAFT. Remedy: DEALERS WILL REPLACE THE ALUMINUM DRIVELINE WITH A STEEL VERSION.
VEHICLE DESCRIPTION: VEHICLES EQUIPPED WITH 54" REAR AXLE SPACING CONFIGURATION OF THE AIRGLIDE 200 SUSPENSION WITH THE SERVICE APPLICATION IDENTIFIED AS LOGGER, DUMP TRUCK, OR TANKER. THE REAR SUSPENSION IS REGULARLY SUBJECTED TO EXTREME ARTICULATION, RESULTING IN FLEXING OF THE JOINT. Remedy: DEALERS WILL REPLACE THE LOWER SWAY ARM BRACKETS. OWNER NOTIFICATION BEGAN MARCH 27, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT KENWORTH AT 1-425-828-5000.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH TRW TIE ROD ENDS ON CERTAIN MERITOR AXLES. THE TIE ROD AND DRAG LINK BALL STUD ENDS CONTAIN BEARINGS THAT ARE BELOW THE SPECIFIED CASE DEPTH AND/OR HARDNESS. Remedy: DEALERS WILL REMOVE AND REPLACE ALL AFFECTED TIE RODS AND DRAG LINKS WITH DIFFERENT DESIGNED ENDS.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH TIE ROD ASSEMBLIES MANUFACTURED BY TRW. THE SUSPECT TIE RODS CONTAIN 24-DL MODEL BALL SOCKETS. CERTAIN OF THE TIE ROD BALL-SOCKET BEARINGS HAVE A BELOW-SPECIFICATION CASE DEPTH AND/OR HARDNESS, WHICH CAN LEAD TO PREMATURE WEAR OF THE SOCKET. Remedy: DEALERS WILL REPLACE THE DEFECTIVE BALL SOCKETS AND/OR DRAG LINKS. OWNER NOTIFICATION BEGAN ON APRIL 10, 2001, TO KENWORTH OWNERS AND ON APRIL 25, 2001, TO PETERBILT OWNERS. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT KENWORTH AT 1-425-828-5000, PETERBILT AT 1-940-591-4000 OR TRW CUSTOMER SERVICE AT 1-866-280-3287.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH CATERPILLAR ENGINES AND EATON AUTOSHIFT TRANSMISSIONS. THE ENGINES CAN STALL BECAUSE OF SOFTWARE PROBLEMS. Remedy: DEALERS WILL UPDATE THESE ENGINES WITH SOFTWARE CHANGES. CATERPILLAR IS CONDUCTING THE OWNER NOTIFICATION AND REMEDY OF THIS RECALL.
HEAVY DUTY TRUCKS EQUIPPED WITH TRW TIE ROD ENDS ON CERTAIN ARVINMERITOR AND DANA AXLES. PETERBILT WILL RECALL 1,434 VEHICLES EQUIPPED WITH ARVINMERITOR AXLES MANUFACTURED FROM DECEMBER 11, 1999, TO MAY 14, 2000, AND FROM JULY 22 TO SEPTEMBER 30, 2000. KENWORTH WILL RECALL 859 VEHICLES EQUIPPED WITH ARVINMERITOR VEHICLES MANUFACTURED FROM DECEMBER 11, 1999, TO MAY 23, 2000, AND FROM JULY 27, 2000, TO SEPTEMBER 30, 2000 AND KENNWORTH WILL RECALL AN ADDITIONAL 4,151 VEHICLES EQUIPPED WITH DANA AXLES AND MANUFACTURED FROM JUNE 23 TO DECEMBER 6, 1999, AND FROM MAY 23 TO SEPTEMBER 30, 2000. THE TIE ROD AND DRAG LINK BALL STUD ENDS CONTAIN BEARINGS THAT ARE BELOW THE SPECIFIED CASE DEPTH AND/OR HARDNESS. Remedy: DEALERS WILL REMOVE AND REPLACE ALL AFFECTED TIE RODS AND DRAG LINKS WITH DIFFERENT DESIGNED ENDS. OWNER NOTIFICATION BEGAN JULY 15, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT PETERBILT AT 1-940-591-4201 OR KENWORTH AT 1-425-828-5440.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Certain vehicles equipped with TRW brand tie rod model number 24-DL. The tie rod ball-socket bearings have a below specification case depth and/or hardness, which can lead to premature wear of the socket. If this condition occurs, the driver can lose partial control of the right front wheel, possibly resulting in a crash. Correction: Dealers will replace the defective ball sockets and/or drag links.
On certain vehicles, the rear suspension is regularly subjected to extreme articulation, resulting in flexing of the joint. Failure of the lower sway arm attaching bolts could result with possible loss of vehicle control. Correction: Dealers will replace the lower sway arm brackets.
On certain vehicles, the main cab power and battery leads were attached incorrectly to the same side of the 135A circuit breaker when this circuit breaker was mounted in the optional firewall location rather than in the standard battery box location. This condition resulted on the main cab power circuit being unprotected. If a wiring short occurred anywhere along the cab power circuit, the available battery power could arc and cause a possible fire. Correction: Vehicles will be inspected and wiring corrected as required.
On certain vehicles, the drivelines may exceed the 35 degrees in the U-joint angle. This creates the potential of the U-joint contacting the aluminum steering driveline. This contact may result in a notch in the steering driveline, which would result in a stress riser in the shaft. This condition could result in premature failure of the steering driveline and loss of vehicle control. Correction: Aluminum steering driveline will be replaced with a steel version.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain