Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1999 Mack MR, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
ON CERTAIN CHASSIS BUILT WITH LNG ENGINES, THE NEXGEN LNG TANK'S PRIMARY AND SECONDARY RELIEF VALVES COULD FAIL TO OPEN AND RELIEVE TANK PRESSURE. Remedy: DEALERS WILL RETROFIT THE LNG TANKS WITH A NEW PRIMARY RELIEF VALVE PIPE AWAY TUBE AND A NEW VENTILATED SHROUD. THE RECALL BEGAN APRIL 6, 2004. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT MACK AT 1-610-709-3337.
VEHICLE DESCRIPTION: CLASS 8 TRUCKS EQUIPPED WITH FELSTED ELECTRONIC ACCELERATOR PEDALS. THE RETURN SPRINGS CAN BREAK ON THE ACCELERATOR PEDALS THAT ARE EQUIPPED WITH STAINLESS STEEL OR ELECTROPLATED WIRE RETURN SPRINGS. Remedy: REPLACEMENT ACCELERATOR PEDALS EQUIPPED WITH RETURN SPRINGS MANUFACTURED OF MUSIC WIRE WITH ONE ADDITIONAL COIL ON EACH SPRING AND WITH AN ORGANIC COATING, ELIMINATING ELECTROPLATING WILL BE INSTALLED.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH DRAG LINK ASSEMBLIES CONTAINING 24-DL MODEL BALL SOCKETS AND MANUFACTURED BY TRW. CERTAIN OF THE TIE ROD BALL-SOCKET BEARINGS HAVE A BELOW-SPECIFICATION CASE DEPTH AND/OR HARDNESS, WHICH CAN LEAD TO PREMATURE WEAR OF THE SOCKET. Remedy: DEALERS WILL REPLACE THE DEFECTIVE DRAG LINKS. OWNER/DISTRIBUTOR NOTIFICATION BEGAN AUGUST 30, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT MACK AT 1-610-709-3011 OR TRW CUSTOMER SERVICE AT 1-866-280-3287.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH TIE ROD ASSEMBLIES CONTAINING 24-DL MODEL BALL SOCKETS AND MANUFACTURED BY TRW. CERTAIN OF THE TIE ROD BALL-SOCKET BEARINGS HAVE A BELOW-SPECIFICATION CASE DEPTH AND/OR HARDNESS, WHICH CAN LEAD TO PREMATURE WEAR OF THE SOCKET. Remedy: DEALERS WILL REPLACE THE DEFECTIVE TIE RODS. OWNER NOTIFICATION BEGAN JULY 13, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT MACK AT 1-610-709-3011 OR TRW CUSTOMER SERVICE AT 1-866-280-3287.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS BUILT WITH BENDIX AIR ABS WITH AN EC-17 1030R ELECTRONIC CONTROL UNIT (ECU), THERE HAVE BEEN REPORTS OF UNWANTED ABS ACTIVATION AT LOW SPEEDS CAUSED BY 1) CHAFED ABS WHEEL SPEED SENSOR WIRES ON ROTATING PARTS OR 2) A DAMAGED COMPONENT AT THE WHEEL END THAT GENERATES A CERTAIN TYPE OF ERRATIC SENSOR SIGNAL. Remedy: DEALERS WILL REPLACE THE ABS ECU.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain vehicles, additional axles were installed to increase the gross vehicle weight capacity but the parking brake capacity was not increased accordingly therefore not complying with CMVSS 121 regulations. Correction: The dealer will perform repairs as necessary.
Certain heavy-duty trucks equipped with drag link assemblies containing 24-DL model ball sockets and manufactured by TRW. Certain of the tie rod ball-socket bearings have a below-specification case depth and/or hardness, which can lead to premature wear of the socket. If this condition occurs, the driver can lose partial control of the right front wheel, possibly resulting in a crash. Correction: Dealers will replace the defective drag links.
Certain heavy-duty trucks equipped with tie rod sockets model ball sockets and manufactured by TRW. Certain of the tie rod ball-socket bearings have a below-specification case depth and/or hardness, which can lead to premature wear of the socket. If this condition occurs, the driver can lose partial control of the right front wheel, possibly resulting in a crash. Correction: Dealers will replace the defective tie rods.
On certain vehicles, the return springs on the accelerator pedals are made of stainless steel or electroplated music wire. The design fatigue stress of the stainless steel springs is in a range that would predict that some failures would occur. The music wire springs can fail due to stress risers created by electrical arcing during electroplating. Correction: Accelerator pedals will be replaced with ones equipped with return springs manufactured of music wire with one additional coil on each spring and with an organic coating, eliminating electroplating.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain