Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1999 Volvo VN, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH AN ESPAR COMPACT HEATER MOUNTED IN THE LUGGAGE COMPARTMENT. THE FUEL-METERING PUMP THAT SUPPLIES FUEL TO THE COMPACT HEATER IS NOT WIRED THROUGH A ROLLOVER PROTECTION SWITCH. THIS DOES NOT COMPLY WITH 49 CFR 393.77, "HEATERS." Remedy: DEALERS WILL WIRE THE FUEL-METERING PUMP THROUGH A ROLLOVER PROTECTION SWITCH.
ON SOME HEAVY DUTY CLASS 8 VEHICLES EQUIPPED WITH ARVINMERITOR AXLE ASSEMBLIES WHICH MAY HAVE BEEN MANUFACTURED WITH TRW MODEL 20EDL BALL SOCKETS, THE TIE ROD BALL-SOCKET BEARINGS HAVE A BELOW SPECIFICATION CASE DEPTH AND/OR HARDNESS WHICH CAN LEAD TO PREMATURE WEAR OUT OF THE SOCKET IN SOME APPLICATIONS. Remedy: DEALERS WILL REPLACE THE BALL SOCKET ASSEMBLIES. THIS CAMPAIGN SUPERSEDES NHTSA CAMPAIGN NOS. 01V-139.001 AND 02V-037.002. OWNER NOTIFICATION BEGAN JULY 25, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT VOLVO TRUCKS AT 1-800-528-6586.
VEHICLE DESCRIPTION: HEAVY DUTY CLASS 8 VEHICLES EQUIPPED WITH ARVINMERITOR AXLE ASSEMBLIES WHICH MAY HAVE BEEN MANUFACTURED WITH TRW MODEL 20EDL BALL SOCKETS. THE TIE ROD BALL-SOCKET BEARINGS HAVE A BELOW SPECIFICATION CASE DEPTH AND/OR HARDNESS WHICH CAN LEAD TO PREMATURE WEAR OUT OF THE SOCKET IN SOME APPLICATIONS. Remedy: DEALERS WILL REPLACE THE BALL SOCKET ASSEMBLIES. THE CAMPAIGN HAS BEEN SUPERCEDED BY RECALL NO. 02V037002. OWNER NOTIFICATION BEGAN NOVEMBER 17, 2000. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT VOLVO TRUCKS AT 1-800-528-6586.
VEHICLE DESCRIPTION: HEAVY DUTY CLASS 8 VEHICLES. UNDER CERTAIN OPERATING CONDITIONS, THE WEIGHT CERTIFICATION LABEL WHICH CONTAINS FRONT GROSS AXLE WEIGHT RATING (GAWR) INFORMATION PURSUANT TO THE REQUIREMENTS OF FMVSS NO. 120, "TIRE SELECTION AND RIMS FOR MOTOR VEHICLES OTHER THAN PASSENGER CARS," DOES NOT ACCURATELY REFLECT THE ACTUAL FRONT GROSS AXLE WEIGHT. Remedy: THE WEIGHT CERTIFICATION LABEL WILL BE BROUGHT INTO COMPLIANCE BY ONE OR MORE OF THE FOLLOWING MEANS: (1) REPLACEMENT OF THE LABEL WITH ONE WHICH CONTAINS CORRECT INFORMATION; OR (2) REPLACEMENT OF FRONT AXLE TIRES, RIMS OR TIE ROD TUBE OR A COMBINATION THEREOF; OR (3) REPLACEMENT OR RELOCATION OF THE FUEL TANKS. DUE TO THE VARIOUS TRUCK CONFIGURATIONS, SEVERAL OWNER NOTIFICATION LETTERS ARE BEING SENT FOR THIS CAMPAIGN. THE FIRST OWNER NOTIFICATION LETTER WAS MAILED APRIL 26, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY OR LABEL WITHIN A REASONABLE TIME SHOULD CONTACT VOLVO TRUCKS AT 1-800-528-6586.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH MERITOR AIR BRAKE AUTOMATIC SLACK ADJUSTERS. SOME OF THE AUTOMATIC SLACK ADJUSTERS HAD INSUFFICIENT TORQUE APPLIED TO THE GUIDE PAWL CAP SCREW. Remedy: DEALERS WILL CHECK THE TORQUE ON THE AUTOMATIC SLACK ADJUSTER GUIDE PAWL. IF THERE IS NO TORQUE, THE BRAKES WILL BE ADJUSTED AND THE GUIDE PAWL WILL BE TIGHTENED TO 15-20 FT. LBS.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Certain vehicles affected may contain tie rod assemblies, model 20-EDL, manufactured by TRW. These tie rods may display premature wear that could eventually lead to the ball stud seperating from the socket assembly causing a possible loss of steering control. Correction: Dealer will replace the tie rod assemblies.
The steer axle tie rod ball-socket assembly ball stud may separate from the socket due to premature wear. If this event occurs, there will be no steering control to the right steer axle with the potential for a vehicle crash. Correction: suspect tie rod ball-socket assemblies will be inspected and replaced as required by dealers.
On certain vehicles, the certification label which contains front Gross Axle Weight Rating (GAWR) information pursuant to the requirements of CMVSS 120 does not accurately reflect the actual front gross axle weight. When operating the truck "bobtail" with full fuel tanks and two occupants with an allowance for personal belongings, the actual gross axle weight may exceed the stated rating found on the weight certification label. Correction: Dealers will bring the weight certification label into compliance by one or more of the following means: (1) replacement of the label with one which contains correct information; or (2) replacement of front axle tires, rims or tie rod tube or a combination thereof; or (3) replacement or relocation of the fuel tanks. Due to the various truck configurations, several owner notification letters are being sent for this campaign.
On certain vehicles, the steer axle tie rod ball-socket assembly ball stud may separate from the socket due to premature wear. if this event occurs. there will be no steering control to the right steer axle with the potential for a vehicle crash. Correction: Suspect tie rod ball-socket assemblies will be inspected and replaced as required.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
On certain vehicles, the electrical circuit for the fuel metering pump that supplies fuel to the compact (parking) heater does not contain a rollover protection switch that would shut-off electrical current to the fuel metering pump in the event of a vehicle rollover. In a rollover, with the compact heater in operation, fuel would still be supplied to the heater creating the potential for a vehicle fire. Correction: A rollover protection switch will be installed.
On certain vehicles, the brake automatic slack adjuster pull pawl may not have been tightened to the specified torque. If this condition exists, the brake will lose further adjustment, and the affected wheel brake assembly will become ineffective. Correction: The slack adjuster pull pawl will be tightened to the specified torque at all wheel/brake locations.