Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 1999 Volvo WG, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS BUILT WITH BENDIX AIR ABS WITH AN EC-17 1030R ELECTRONIC CONTROL UNIT (ECU), THERE HAVE BEEN REPORTS OF UNWANTED ABS ACTIVATION AT LOW SPEEDS CAUSED BY 1) CHAFED ABS WHEEL SPEED SENSOR WIRES ON ROTATING PARTS OR 2) A DAMAGED COMPONENT AT THE WHEEL END THAT GENERATES A CERTAIN TYPE OF ERRATIC SENSOR SIGNAL. Remedy: DEALERS WILL REPLACE THE ABS ECU.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH TRW 20-EDL BALL-SOCKET ASSEMBLIES. CERTAIN OF THE BALL-SOCKET BEARINGS HAVE A BELOW SPECIFICATION CASE DEPTH AND/OR HARDNESS WHICH CAN LEAD TO PREMATURE WEAR OUT OF THE SOCKET. THESE BEARINGS WERE PRODUCED BETWEEN JULY 5 AND OCTOBER 3, 1999. Remedy: DEALERS WILL REPLACE THE BALL-SOCKET ASSEMBLIES.
ON SOME HEAVY DUTY CLASS 8 VEHICLES EQUIPPED WITH ARVINMERITOR AXLE ASSEMBLIES WHICH MAY HAVE BEEN MANUFACTURED WITH TRW MODEL 20EDL BALL SOCKETS, THE TIE ROD BALL-SOCKET BEARINGS HAVE A BELOW SPECIFICATION CASE DEPTH AND/OR HARDNESS WHICH CAN LEAD TO PREMATURE WEAR OUT OF THE SOCKET IN SOME APPLICATIONS. Remedy: DEALERS WILL REPLACE THE BALL SOCKET ASSEMBLIES. THIS CAMPAIGN SUPERSEDES NHTSA CAMPAIGN NOS. 01V-139.001 AND 02V-037.002. OWNER NOTIFICATION BEGAN JULY 25, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT VOLVO TRUCKS AT 1-800-528-6586.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH A STEEL FUEL TANK. THE CLOSURE ONLY FUEL TANK CAP, INSTALLED ON THE STEEL FUEL TANK, FAILED WHEN THE TANK WAS DROPPED FROM A 10' HEIGHT AS REQUIRED BY FMVSS NO. 393, "LIQUID FUEL TANKS." Remedy: OWNERS WILL BE PROVIDED WITH A NEW FUEL TANK CAP.
VEHICLE DESCRIPTION: HEAVY DUTY CLASS 8 VEHICLES EQUIPPED WITH ARVINMERITOR AXLE ASSEMBLIES WHICH MAY HAVE BEEN MANUFACTURED WITH TRW MODEL 20EDL BALL SOCKETS. THE TIE ROD BALL-SOCKET BEARINGS HAVE A BELOW SPECIFICATION CASE DEPTH AND/OR HARDNESS WHICH CAN LEAD TO PREMATURE WEAR OUT OF THE SOCKET IN SOME APPLICATIONS. Remedy: DEALERS WILL REPLACE THE BALL SOCKET ASSEMBLIES. THE CAMPAIGN HAS BEEN SUPERCEDED BY RECALL NO. 02V037002. OWNER NOTIFICATION BEGAN NOVEMBER 17, 2000. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT VOLVO TRUCKS AT 1-800-528-6586.
CERTAIN HEAVY DUTY CLASS 8 TRUCKS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THE TWO TAIL LAMPS, BACK-UP LAMP,AND LICENSE TAG LAMP WERE MOUNTED ON INSUFFICIENTLY RIGID MOUNTS. Remedy: DEALERS WILL ATTACH THE TWO TAIL LAMPS, BACK-UP LAMP, AND THE LICENSE TAP LAMP ON STIFFER BRACKETS. OWNER NOTIFICATION BEGAN OCTOBER 31, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT VOLVO TRUCKS AT 1-800-528-6586.
VEHICLE DESCRIPTION: HEAVY DUTY, CLASS 8, TRUCKS EQUIPPED WITH TIE ROD ASSEMBLIES CONTAINING 24-DL MODEL BALL SOCKETS AND MANUFACTURED BY TRW. CERTAIN OF THE TIE ROD BALL-SOCKET BEARINGS HAVE A BELOW-SPECIFICATION CASE DEPTH AND/OR HARDNESS, WHICH CAN LEAD TO PREMATURE WEAR OF THE SOCKET. Remedy: DEALERS WILL REPLACE THE DEFECTIVE BALL SOCKETS AND/OR DRAG LINKS. OWNER NOTIFICATION BEGAN DURING MAY 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT VOLVO TRUCKS AT 1-800-528-6586.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH MERITOR AIR BRAKE AUTOMATIC SLACK ADJUSTERS. SOME OF THE AUTOMATIC SLACK ADJUSTERS HAD INSUFFICIENT TORQUE APPLIED TO THE GUIDE PAWL CAP SCREW. Remedy: DEALERS WILL CHECK THE TORQUE ON THE AUTOMATIC SLACK ADJUSTER GUIDE PAWL. IF THERE IS NO TORQUE, THE BRAKES WILL BE ADJUSTED AND THE GUIDE PAWL WILL BE TIGHTENED TO 15-20 FT. LBS.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Certain vehicles affected may contain tie rod assemblies, model 20-EDL, manufactured by TRW. These tie rods may display premature wear that could eventually lead to the ball stud seperating from the socket assembly causing a possible loss of steering control. Correction: Dealer will replace the tie rod assemblies.
The steer axle tie rod ball-socket assembly ball stud may separate from the socket due to premature wear. If this event occurs, there will be no steering control to the right steer axle with the potential for a vehicle crash. Correction: suspect tie rod ball-socket assemblies will be inspected and replaced as required by dealers.
Certain trucks may have improperly heat treated drag link assemblies which can lead to premature wear of the ball socket. If this condition occurs, the driver can lose steering control, possibly resulting in a crash. Correction: Dealers will replace the defective drag links.
On certain vehicles, the steer axle tie rod ball-socket assembly ball stud may separate from the socket due to premature wear. if this event occurs. there will be no steering control to the right steer axle with the potential for a vehicle crash. Correction: Suspect tie rod ball-socket assemblies will be inspected and replaced as required.
On certain vehicles, the steering assist cylinder ball-socket assembly ball stud may separate from the socket due to premature wear. If this event occurs, increased steering effort will result, creating the potential for a vehicle crash. Correction: Ball socket assemblies will be replaced.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
On certain vehicles, the ABS ECU misinterprets certain signals from wheel ends which can result in the temporary loss of braking capability on one or more wheel positions for several seconds. This response results from either an ABS cable that has chafed through the insulation and contacted a rotating part or a misaligned tone ring that has been damaged by contacting other components. Correction: ABS ECU will be replaced with a new ECU with upgraded software capable of detecting and properly responding to erroneous signals.
On certain vehicles, the brake automatic slack adjuster pull pawl may not have been tightened to the specified torque. If this condition exists, the brake will lose further adjustment, and the affected wheel brake assembly will become ineffective. Correction: The slack adjuster pull pawl will be tightened to the specified torque at all wheel/brake locations.