Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2000 Kenworth T2000, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH BRAKE VALVES MANUFACTURED BY HONEYWELL BENDIX. THE ORIENTATION AND LOCATION OF THE BRAKE VALVE IS SUCH THAT WATER CAN GET INTO THE VALVE THROUGH A VENT IN THE VALVE. THE WATER WILL CONTAMINATE THE AIR SYSTEM AND COULD FREEZE THE BRAKE VALVE. Remedy: DEALERS WILL INSPECT THE AIR BRAKE SYSTEM AND MODIFICATIONS WILL BE MADE TO THE BRAKE VALVE.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH TRW TIE ROD ENDS ON CERTAIN MERITOR AXLES. THE TIE ROD AND DRAG LINK BALL STUD ENDS CONTAIN BEARINGS THAT ARE BELOW THE SPECIFIED CASE DEPTH AND/OR HARDNESS. Remedy: DEALERS WILL REMOVE AND REPLACE ALL AFFECTED TIE RODS AND DRAG LINKS WITH DIFFERENT DESIGNED ENDS. OWNER NOTIFICATION BEGAN OCTOBER 24, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT PETERBILT AT 1-940-591-4000 OR KENWORTH AT 1-425-828-5000.
ON CERTAIN TRUCKS EQUIPPED WITH TRUCK HUB UNITS MANUFACTURED BY SKF EXCLUSIVELY FOR USE ON ARVINMERITOR'S FF98X SERIES NON-DRIVE STEER AXLES, THE HUB UNIT BEARINGS CAN WEAR PREMATURELY. Remedy: DEALERS WILL REPLACE ALL FRONT AXLE HUBS. NOTIFICATION BEGAN JULY 16, 2003. THE MANUFACTURER HAS ADVISED US THAT PARTS WILL NOT BE AVAILABLE UNTIL SEPTEMBER 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITH A REASONABLE TIME SHOULD CONTACT PETERBILT AT 940-591-4201 OR KENWORTH 425-828-5440.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH EATON AUTOSHIFT GEN II TRANSMISSION ASSEMBLIES. DUE TO A SOFTWARE PROBLEM IN THE TRANSMISSION ASSEMBLIES, THE TRANSMISSION WILL SELECT THE WRONG GEAR. Remedy: DEALERS WILL REPLACE THE AUTOSHIFT TRANSMISSIONS. EATON PERFORMED THE CAMPAIGN FOR THE KENWORTH PORTION. HOWEVER PETERBILT WILL BE CONDUCTING THEIR OWN CAMPAIGN.
VEHICLE DESCRIPTION: VEHICLES EQUIPPED WITH 54" REAR AXLE SPACING CONFIGURATION OF THE AIRGLIDE 200 SUSPENSION WITH THE SERVICE APPLICATION IDENTIFIED AS LOGGER, DUMP TRUCK, OR TANKER. THE REAR SUSPENSION IS REGULARLY SUBJECTED TO EXTREME ARTICULATION, RESULTING IN FLEXING OF THE JOINT. Remedy: DEALERS WILL REPLACE THE LOWER SWAY ARM BRACKETS. OWNER NOTIFICATION BEGAN MARCH 27, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT KENWORTH AT 1-425-828-5000.
HEAVY DUTY TRUCKS EQUIPPED WITH TRW TIE ROD ENDS ON CERTAIN ARVINMERITOR AND DANA AXLES. PETERBILT WILL RECALL 1,434 VEHICLES EQUIPPED WITH ARVINMERITOR AXLES MANUFACTURED FROM DECEMBER 11, 1999, TO MAY 14, 2000, AND FROM JULY 22 TO SEPTEMBER 30, 2000. KENWORTH WILL RECALL 859 VEHICLES EQUIPPED WITH ARVINMERITOR VEHICLES MANUFACTURED FROM DECEMBER 11, 1999, TO MAY 23, 2000, AND FROM JULY 27, 2000, TO SEPTEMBER 30, 2000 AND KENNWORTH WILL RECALL AN ADDITIONAL 4,151 VEHICLES EQUIPPED WITH DANA AXLES AND MANUFACTURED FROM JUNE 23 TO DECEMBER 6, 1999, AND FROM MAY 23 TO SEPTEMBER 30, 2000. THE TIE ROD AND DRAG LINK BALL STUD ENDS CONTAIN BEARINGS THAT ARE BELOW THE SPECIFIED CASE DEPTH AND/OR HARDNESS. Remedy: DEALERS WILL REMOVE AND REPLACE ALL AFFECTED TIE RODS AND DRAG LINKS WITH DIFFERENT DESIGNED ENDS. OWNER NOTIFICATION BEGAN JULY 15, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT PETERBILT AT 1-940-591-4201 OR KENWORTH AT 1-425-828-5440.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Certain heavy duty trucks equipped with TRW tie rod ends on certain meritor axles. The tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness. This can lead to premature wear with possible separation of the ball stud from the socket, increasing the risk of loss of control of the vehicle. Correcton: Dealers will remove and replace all affected tie rods and drag links with different designed ends.
On certain vehicles, the rear suspension is regularly subjected to extreme articulation, resulting in flexing of the joint. Failure of the lower sway arm attaching bolts could result with possible loss of vehicle control. Correction: Dealers will replace the lower sway arm brackets.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain