Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2000 Subaru Legacy, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
Airtex Products LP (Airtex) is recalling certain model E8598M, E8518M, E8600M, E8596M, and E8597M fuel pumps manufactured July 26, 2013, and July 29, 2013 and used as aftermarket replacements on Subaru Baja's, Outback's and Legacy's. The affected fuel pumps were sold or installed into the aftermarket applications on or after July 26, 2013, and may may leak fuel from the base of a fuel line connection when the gas tank is full. Remedy: Airtex will notify owners, and will replace the fuel pump, free of charge. Recall is expected to begin on January 2, 2014. Customers may contact Airtex at 1-800-880-3056. The recall is expected to begin during January 2014. This recall is being conducted by Airtex, not by Subaru.
THIS RECALL APPLIES TO CERTAIN PASSENGER VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, KENTUCKY, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, VIRGINIA, WEST VIRGINIA, WISCONSIN, AND THE DISTRICT OF COLUMBIA. CERTAIN REAR SUSPENSION SUBFRAME COMPONENTS WERE PRODUCED WITH POOR PAINT QUALITY WHICH, AFTER CONTINUED EXPOSURE TO CORROSIVE ROAD SALTS FOR A PERIOD OF SEVERAL YEARS, COULD RESULT IN RUST-OUT OF THE COMPONENT AND POSSIBLE BREAKAGE OF THE SUBFRAME. Remedy: DEALERS WILL CLEAN AND RUST-PROOF THE REAR SUSPENSION SUBFRAME. OWNER NOTIFICATION BEGAN JULY 14, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT SUBARU AT 1-800-782-2783.
VEHICLE DESCRIPTION: SEDAN L MODEL PASSENGER VEHICLES. ANTI-RUST COATING WAS INCORRECTLY APPLIED TO THE TRANSVERSE LINK MOUNTING SURFACE OF THE VEHICLE BODY. OVER TIME THE COATING SHRINKS, CAUSING A TORQUE DECREASE OF THE BOLT THAT SECURES THE TRANSVERSE LINK BRACKET TO THE VEHICLE BODY. Remedy: DEALERS WILL INSPECT THE VEHICLES AND, IF NECESSARY, REMOVE THE ANTI-RUST COATING UNDER THE MOUNTING LOCATION OF THE LEFT TRANSVERVE LINK MOUNTING BRACKET BOLT AND RETORQUE THE MOUNTING BOLT TO THE REQUIRED TORQUE.
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE LEFT-SIDE STEERING KNUCKLE ARM WAS INCORRECTLY ASSEMBLED. Remedy: DEALERS WILL INSPECT THE TORQUE ON THE LEFT SIDE TIE-ROD END CASTLE NUT AND INSTALL A NEW COTTER PIN.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain vehicles operated in the "salt-belt" provinces of Manitoba, Ontario, Québec, New Brunswick, Nova Scotia, Prince Edward Island and Newfoundland & Labrador. The rear suspension subframe components were produced with poor paint quality which, after continued exposure to corrosive road salts for a period of several years, may result in rust-out of the component and possible breakage of the subframe. Correction: Dealer will clean and rust-proof with anti-rust oil and anti-rust wax.
Certain vehicles do not comply with the marking requirements of CMVSS 108 - Lighting System and Retroreflective Devices. The High/Low beam headlamp on these vehicles does not bear a "DOT" marking which is required by the standard. Correction: All High/Low beam headlamp bulbs installed since February 8, 2000 have the correct marking. Since the subject bulbs meets or exceed the performance and design requirements of the standard, and the missing marking will not cause a person to replace, fit or use the bulb in a manner for which they are not intended, no further action will be taken.
On certain vehicles, the headlamp assemblies may not comply with the marking requirements of CMVSS 108 - Lighting System and Retroreflective Devices. The bulb center mark on the lens has been interchanged between 2-bulb headlamps and 4-bulb headlamps. Correction: No corrective action will be taken due to the inconsequence to vehicle safety. The manufacturing process has been remedied to assure correction of the non-compliance on vehicles manufactured since January 30, 2000.
Certain vehicles do not comply with Cthe requirements of CMVSS 108 - Lighting System and Retroreflective Devices. The H1 low-beam headlamp bulbs do not bear a "DOT" marking as required by the standard. Correction: Since these bulbs comply with all performance and design requirements of the standard, no corrective action will be taken.
We checked the EU Safety Gate for recall alerts naming this model and its production years.
Source: EU Safety Gate (European Commission) · CC BY 4.0, © European Union
The Electronic Park Brake (EPB) may not operate as intended. This can lead to the vehicle moving or rolling away whilst in the park brake mode, creating a risk of an accident. Production dates not stated in the alert. Types: e1*2007/46*0079*05; e1*2007/46*1320*00; e1*2007/46*1320*01; e1*2007/46*1320*02; e1*2007/46*0079*08; e13*2007/46*1648*02; e13*2007/46*1678*03; e13*2007/46*1648*04; e1*2007/46*0597*08; e1*2007/46*1648*02; e1*2007/46*1203*03; e1*2007/46*1203*04; e1*2007/46*1203*05; e1*2007/46*1320*02.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Crash-test ratings from NHTSA's New Car Assessment Program.
Source: NHTSA (US Department of Transportation) · US public domain
Certain vehicle do not comply with Regulation 6 - Statement of Compliance. Compliance label was not expressed in both official languages in regard to vehicle classification. Correction: No corrective action will be taken for existing vehicles. Correct compliance label will be affixed in current production vehicles.
On certain vehicles, incorrect application of anti-rust coating (PVC) to the transverse link mounting surface can eventually result in a torque decrease of the bolt that secures the transverse link bracket to the vehicle body. Insufficient torque on the bracket bolts can result in loosening of the bracket and subsequent separation of the transverse link from the vehicle frame. Correction: Vehicles will be inspected and if necessary, PVC will be removed from the vehicle body under the transverse link mounting bracket bolt location and mounting bolts will be retorqued to specification.