Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2001 Chevrolet Silverado, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
K2 MOTOR IS RECALLING 1,921 AFTERMARKET HEADLAMPS OF VARIOUS MODELS SOLD FOR USE ON THE ABOVE LISTED VEHICLES. THESE HEADLAMPS ARE MISSING THE AMBER SIDE REFLEX REFLECTOR WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." Remedy: K2 MOTOR WILL NOTIFY OWNERS AND OFFER A FULL REFUND. THE RECALL BEGAN ON DECEMEBER 17, 2008. OWNERS MAY CONTACT K2 MOTOR AT 1-909-839-2992.
CERTAIN AAI MOTORSPORTS COMBINATION LAMPS SOLD AS REPLACEMENT LAMPS FOR USE ON THE ABOVE LIST PASSENGER VEHICLES. COMBINATION LAMPS NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." Remedy: AAI MOTORSPORTS WILL NOTIFY OWNERS AND REPLACE THE LAMPS FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 1, 2006. OWNERS MAY CONTACT AAI MOTORSPORTS AT 909-923-9188.
SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS. Remedy: SABERSPORT WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON MAY 11, 2009. OWNERS MAY CONTACT SABERSPORT AT 1-909-598-7589.
CERTAIN MAXZONE HEADLIGHT ASSEMBLIES, DEPO BRAND, P/NOS. 332-1182L-AS AND 332-1182R-AS, SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR 1999-2000 CHEVROLET SILVERADOS. THESE HEADLAMPS FAIL TO CONFORM TO THE PHOTOMETRIC REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT. Remedy: MAXZONE WILL NOTIFY OWNERS AND OFFER FOR REIMBURSEMENT ANY NONCOMPLIANT HEADLIGHTS. THE RECALL BEGAN ON JULY 10, 2006. OWNERS MAY CONTACT MAXZONE AT 909-822-3288.
DOPE, INC. IS RECALLING 42,540 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS. Remedy: DOPE, INC. WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON JULY 28, 2009. OWNERS MAY CONTACT DOPE, INC. AT 1-626-272-1798.
CERTAIN GUIDE REPLACEMENT HEADLAMPS, P/NOS. 16526133 AND 16526134, MANUFACTURED FROM JANUARY 1 TO JULY 11, 2006, SOLD FOR USE ON MY 1999-2002 CHEVROLET SILVERADO PICKUP TRUCKS. THE HEADLAMP FAIL TO COMPLY WITH THE PHOTOMETRY REQUIREMENT OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT. Remedy: GUIDE CORPORATION WILL NOTIFY OWNERS AND REPLACE THE HEADLAMPS FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 31, 2006. OWNERS MAY CONTACT GUIDE AT 248-874-0355.
CERTAIN PRO-A MOTORS CORNER LAMPS, TURN SIGNALS, AND HEADLIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON CERTAIN PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT. Remedy: PRO-A MOTORS WILL NOTIFY OWNERS AND OFFER TO REPURCHASE THE LAMPS. THE RECALL BEGAN ON APRIL 3, 2006. OWNERS MAY CONTACT PRO-A MOTORS AT 323-838-2988.
ON CERTAIN PICKUP TRUCKS EQUIPPED WITH AN 8.1L V8 ENGINE, THE CRANKSHAFT POSITION CAN OPERATE INTERMITTENTLY OR FAIL COMPLETELY. IF THE SENSOR OPERATES INTERMITTENTLY, THE SES LIGHT MAY ILLUMINATE AND THE VEHICLE MAY RUN ROUGH. THE ENGINE MAY STALL, AND IF SO, MAY RE-START IMMEDIATELY OR AFTER A COOL DOWN PERIOD. Remedy: DEALERS WILL REPLACE THE CRANKSHAFT POSITION SENSOR FREE OF CHARGE. THE RECALL BEGAN ON DECEMBER 18, 2007. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438 AND GMC AT 1-866-996-9463.
CERTAIN CEQUENT 90 DEGREE 7-WAY RIGHT ANGLE ADAPTORS SOLD BY DISTRIBUTORS IN TOW PACKAGES FOR AFTERMARKET SALES TO TOW 5TH WHEEL RV TRAVEL TRAILERS. DUE TO INCORRECT WIRING OF THE HARNESS, THE TRAILER LIGHTS MAY NOT OPERATE PROPERLY. Remedy: ALL OF THE DEFECTIVE TOW PACKAGES ARE STILL AT THE DISTRIBUTOR LEVEL AND HAVE NOT BEEN SOLD TO ANY CONSUMERS.
CERTAIN EAGLE EYES REPLACEMENT HEADLAMPS, MODEL NOS. GM159-B001L AND GM159-B001R, SOLD FOR USE ON 1999-2002 CHEVROLET SILVERADO MODEL VEHICLES. THE HEADLAMPS FAIL TO CONFORM TO THE PHOTOMETRIC REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT. Remedy: SABRY LEE WILL NOTIFY OWNERS AND ISSUE FULL CREDIT. THE RECALL BEGAN ON MAY 10, 2006. OWNERS MAY CONTACT SABRY LEE AT 1-866-467-2279.
CERTAIN FEDERAL-MOGUL REPLACEMENT WHEEL HUB ASSEMBLIES WITH THE BRAND NAMES: NATIONAL, CARQUEST P/NOS. 515020, 515021, 515025, 515053, 515054, 515059, AND 515060, SHIPPED BETWEEN JANUARY 23, 2006, AND DECEMBER 20, 2007, SOLD FOR LIGHT DUTY AND MEDIUM DUTY TRUCKS. THE INBOARD RETENTION NUT USED TO MAINTAIN HUB BEARING ASSEMBLY CAN LOOSEN RESULTING IN AN ABS LIGHT INDICATION, NOISE, AND/OR WHEEL SEPARATION. Remedy: FEDERAL-MOGUL WILL NOTIFY CUSTOMERS AND WILL REPLACE THE HUB ASSEMBLY FREE OF CHARGE. THE RECALL BEGAN ON FEBRUARY 7, 2008. OWNERS CAN CONTACT FEDERAL-MOGUL TOLL-FREE AT 877-489-6659.
ON CERTAIN PICKUP TRUCKS EQUIPPED WITH MANUAL TRANSMISSIONS AND BUILT WITH EITHER PBR PARKING BRAKE SYSTEMS OR TRW PARKING BRAKE SYSTEMS, THE PARKING BRAKE FRICTION LININGS MAY WEAR TO AN EXTENT WHERE THE PARKING BRAKE CAN BECOME INEFFECTIVE IN IMMOBILIZING A PARKED VEHICLE. Remedy: DEALERS WILL INSTALL A LOW-FORCE SPRING CLIP RETAINER FOR VEHICLES EQUIPPED WITH A PBR PARKING BRAKE SYSTEM. ON VEHICLES EQUIPPED WITH THE TRW PARKING BRAKE SYSTEM, DEALERS WILL INSTALL A REDESIGNED PARKING BRAKE CABLE ASSEMBLY. THE RECALL BEGAN ON JULY 29, 2005. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438 OR GMC AT 1-866-996-9463.
CERTAIN PICKUP TRUCKS AND SPORT UTILITY VEHICLES MAY EXPERIENCE UNWANTED ANTILOCK BRAKE SYSTEM (ABS) ACTIVATION. THIS CONDITION IS MORE LIKELY TO OCCUR IN ENVIRONMENTALLY CORROSIVE AREAS. THIS RECALL WILL BE LAUNCHED IN THE "SALT BELT" STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MARYLAND, MASSACHUSETTS, MAINE, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, WISCONSIN AND THE DISTRICT OF COLUMBIA ONLY. Remedy: DEALERS ARE TO REMOVE THE WHEEL SPEED SENSOR AND THOROUGHLY CLEAN THE WHEEL SPEED SENSOR MOUNTING SURFACE ON THE BEARING, APPLY RUST INHIBITOR TO THE CLEANED SURFACE, GREASE THE MOUNTING SURFACE, REINSTALL THE WHEEL SPEED SENSOR, AND CHECK THE PEAK-TO-PEAK OUTPUT VOLTAGE TO ENSURE THE WHEEL SPEED SIGNAL IS WITHIN SPECIFICATIONS. THE RECALL BEGAN SEPTEMBER 22, 2005. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438 OR GMC AT 1-866-996-9463.
AFTERMARKET PICKUP TRUCK OVER-THE-RAIL BEDLINERS MANUFACTURED FOR INSTALLATION ON 1999-2004 CHEVROLET SILVERADO AND GMC SIERRA PICKUP TRUCKS. THE TOGGLE WING ASSEMBLY USED TO ATTACH THE BEDLINER TO THE TRUCK BED IS NOT ENGAGING FULLY IN THE STAKE POCKET OF THE PICKUP TRUCK. Remedy: DURAKON WILL ISSUE A PRESS RELEASE IN ATTEMPT TO NOTIFY CUSTOMERS THAT COULD HAVE PURCHASED THE DEFECTIVE BEDLINER. IF YOU PURCHASED EITHER A DURAKON ALLSTAR OF PATRIOT OVERRAIL BEDLINER SINCE AUGUST 1, 2003, FOR 1999 TO 2004 CHEVROLET SILVERADO OR GMC SIERRA TRUCKS, OR PURCHASED ONE OF THESE PICKUP TRUCKS WITH EITHER BRAND BEDLINER ALREADY INSTALLED, YOU SHOULD RETURN TO AN AUTHORIZED DURAKON DEALER SO THAT THE BEDLINER CAN BE INSPECTED AND, IF NECESSARY, REPAIRED WITH A NEWLY DESIGNED TOGGLE WING FASTENING SYSTEM, OR IF REQUIRED, REPLACED WITH A NEW BEDLINER FREE OF CHARGE. PLEASE CALL THE DURAKON HOTLINE AT 1-800-933-4200 TO FIND THE NEAREST AUTHORIZED DURAKON DEALER.
ON CERTAIN PICKUP TRUCKS AND SPORT UTILITY VEHICLES, THE GALVANIZED STEEL TAILGATE SUPPORT CABLES THAT RETAIN THE TAILGATE IN THE FULL OPEN (HORIZONTAL) POSITION MAY CORRODE, WEAKEN, AND EVENTUALLY FRACTURE. IF BOTH CABLES FRACTURED, THE TAILGATE WOULD SUDDENLY DROP AND STRIKE THE TOP SURFACE OF THE REAR BUMPER. Remedy: DEALERS WILL REPLACE THE CABLES. INTERIM OWNER NOTIFICATION BEGAN ON APRIL 7, 20004. THE RECALL BEGAN ON SEPTEMBER 24, 2004, WHEN REPLACEMENT PARTS WERE AVAILABLE, AND WILL CONTINUE THROUGH OCTOBER 29, 2004. OWNERS SHOULD CONTACT CADILLAC AT 1-866-982-2339, CHEVROLET AT 1-800-630-2438 OR GMC AT 1-866-996-9463, OR VISIT WWW.MYGMLINK.COM, AND ENTER YOUR VEHICLE IDENTIFICATION NUMBER.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain vehicles equipped with an 8.1L engine, the crankshaft position sensor may fail. If the sensor operates intermittently, the Service Engine Soon (SES) light may illuminate and the vehicle may run rough. In addition, the engine may stall, and if so, may re-start immediately or after a cool-down period. If the sensor becomes inoperable permanently, the engine will quit running and will not re-start. Engine stalling would result in lost propulsion which, in conjunction with traffic and road conditions, and the driver's reactions, could increase the risk of a crash. Correction: Dealers will replace the crankshaft position sensor.
On certain 1999-2002 1500 series and 2001-2005 2500 & 3500 series trucks equipped with a manual transmission, the parking brake friction lining may wear to an extent where the parking brake can become ineffective in immobilizing a parked vehicle. Correction: Dealers will install a low-force spring clip retainer on vehicles equipped with PBR parking brake system and install a redesigned parking brake cable assembly on vehicle equipped with a TRW parking brake system.
Certain vehicles located in Ontario, Quebec, New Brunswick, Nova Scotia, Prince Edward Island, and Newfoundland & Labrador may experience unwanted Antilock Brake System (ABS) activation and increased stopping distances during low-speed brake application (less than 16 km/h and greater than 6 km/h). This condition does not set any ABS codes nor does it illuminate the ABS warning lamp. Correction: Dealers will remove the wheel speed sensor and thoroughly clean the wheel speed sensor mounting surface on the bearing, apply Zinc-X to the cleaned surface, grease the mounting surface, reinstall the wheel speed sensor, and check the output voltage to ensure the wheel speed signal is within specifications.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Crash-test ratings from NHTSA's New Car Assessment Program.
Source: NHTSA (US Department of Transportation) · US public domain
On certain vehicles, the galvanized-braided-steel tailgate support cables used to support the tailgate in the full open (horizontal) position can corrode over time and fracture when loads are applied to them. Tailgate support cable corrosion may not be visible because of the plastic sheathing covering the cable. If one cable fractured, the remaining cable may retain the tailgate in a horizontal position. If the remaining cable was weakened by corrosion, it could fracture within moments of the first cable fracture. If both cables fractured, the tailgate would suddenly drop approximately 10 degrees and strike the top surface of the rear bumper. If anyone is sitting or standing on the horizontal surface of the tailgate when both cables fracture, they could fall and be injured. On vehicles without a rear bumper, the tailgate may drop to a lower position. Correction: Dealers will replace the existing galvanized support cables with stainless steel support cables.
Certain vehicles fail to conform to CMVSS 209, seat belt assemblies. These vehicles have a condition where one or two sensors in the driver's and front seat passengers seat belt retractors may be inoperative. The seat belt retractors will lock when the belt webbing is extracted during a crash; however the mechanism that locks the seat belt retractor when the vehicle decelerates quickly, such as during heavy braking, may not restrain the occupant as intended during a crash, and could result in injury to the occupant. Correction update: None required as no effect on vehicle safety. See recall 04-158.
Certain 2500 and 3500 pickup trucks equipped with 6.6L diesel engines fail to comply with requirements of C.M.V.S.S. No. 105, "Hydraulic and Electric Brake Systems." These vehicles have a brake system warning light in the instrument cluster that may not illuminate when the brake fluid is low. In addition, when the brake fluid is low, the vehicle may not meet the partial system requirements of C.M.V.S.S. No. 105. These conditions could result in reduced braking capability, which could lead to a crash. Correction: Dealers will change the location of a wire connection in the underhood bussed electrical center.
Certain vehicles have an internal component in the 2nd and 3rd row outboard seat belt retractor that could be cracked. With repeated actuation of the locking mechanism, the crack could spread to the point where the seat belt would no longer lock. In a crash, increased occupant injury could result from the no-lock condition. Correction: Dealers will inspect the outboard seat belts for specific lot numbers and replace the belts if necessary. GM is enclosing an inspection procedure for the owners to use or they can have their dealers do the inspections.
Certain vehicles do not comply with the requirements of CMVSS 120 - Tire Selection and Rims for Vehicles Other Than Passenger Cars. Vehicles have a Certification and Tire Pressure Label on which the tire description and tire inflation pressures may not meet the requirements of the standard. Correction: Dealers will install an new label.
On certain vehicles, either or both of the two Body Pressure Relief Valves (PRV) may not seal properly during the life of the vehicle if the body installed on the vehicle does not protect the PRV's from road debris. If the PRV valve does not seal, exhaust fumes could enter into the passenger cab. Correction: Dealer will inspect vehicle to ensure that the PRV is protected by the body of the vehicle. If the PRV is not protected by the body, dealer will install a new shielded PRV.