Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2001 GMC Yukon XL, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
CERTAIN TRUCKS AND SPORT UTILITY VEHICLES WERE BUILT WITH FUEL MODULE RESERVOIR ASSEMBLIES THAT CONTAIN FUEL PUMP WIRES CONNECTORS MAY OVERHEAT UNDER CERTAIN OPERATING CONDITIONS. Remedy: DEALERS WILL REMOVE THE FUEL TANK, AND REMOVE THE MODULE RESERVOIR ASSEMBLIES FROM THE TANK, AND INSTALL A NEW SERVICE KIT FREE OF CHARGE. AN INTERIM LETTER TO OWNERS WAS MAILED ON MAY 25, 2005. THE OWNERS WERE RE-NOTIFIED ON OCTOBER 19, 2005, SINCE PARTS ARE NOW AVAILABE. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438 AND GMC AT 1-866-996-9463.
CERTAIN FEDERAL-MOGUL REPLACEMENT WHEEL HUB ASSEMBLIES WITH THE BRAND NAMES: NATIONAL, CARQUEST P/NOS. 515020, 515021, 515025, 515053, 515054, 515059, AND 515060, SHIPPED BETWEEN JANUARY 23, 2006, AND DECEMBER 20, 2007, SOLD FOR LIGHT DUTY AND MEDIUM DUTY TRUCKS. THE INBOARD RETENTION NUT USED TO MAINTAIN HUB BEARING ASSEMBLY CAN LOOSEN RESULTING IN AN ABS LIGHT INDICATION, NOISE, AND/OR WHEEL SEPARATION. Remedy: FEDERAL-MOGUL WILL NOTIFY CUSTOMERS AND WILL REPLACE THE HUB ASSEMBLY FREE OF CHARGE. THE RECALL BEGAN ON FEBRUARY 7, 2008. OWNERS CAN CONTACT FEDERAL-MOGUL TOLL-FREE AT 877-489-6659.
VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS AND SPORT UTILITY VEHICLES. SOME OF THESE VEHICLES HAVE LOOSE OR MISSING REAR WHEELHOUSE PLUGS. UNDER CERTAIN VEHICLE OPERATING CONDITIONS, EXHAUST GASES CAN FLOW FORWARD AND ACCUMULATE IN THE REAR WHEELHOUSE. Remedy: DEALERS WILL INSPECT THE VEHICLE FOR LOOSE OR MISSING WHEELHOUSE PLUGS AND INSTALL NEW PLUGS IF NECESSARY.
CERTAIN PICKUP TRUCKS AND SPORT UTILITY VEHICLES MAY EXPERIENCE UNWANTED ANTILOCK BRAKE SYSTEM (ABS) ACTIVATION. THIS CONDITION IS MORE LIKELY TO OCCUR IN ENVIRONMENTALLY CORROSIVE AREAS. THIS RECALL WILL BE LAUNCHED IN THE "SALT BELT" STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MARYLAND, MASSACHUSETTS, MAINE, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, WISCONSIN AND THE DISTRICT OF COLUMBIA ONLY. Remedy: DEALERS ARE TO REMOVE THE WHEEL SPEED SENSOR AND THOROUGHLY CLEAN THE WHEEL SPEED SENSOR MOUNTING SURFACE ON THE BEARING, APPLY RUST INHIBITOR TO THE CLEANED SURFACE, GREASE THE MOUNTING SURFACE, REINSTALL THE WHEEL SPEED SENSOR, AND CHECK THE PEAK-TO-PEAK OUTPUT VOLTAGE TO ENSURE THE WHEEL SPEED SIGNAL IS WITHIN SPECIFICATIONS. THE RECALL BEGAN SEPTEMBER 22, 2005. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438 OR GMC AT 1-866-996-9463.
VEHICLE DESCRIPTION: PICKUP AND UTILITY TRUCKS. SOME OF THESE VEHICLES HAVE AN INTERNAL COMPONENT IN THE OUTBOARD SEAT BELT RETRACTORS FOR THE 2ND AND 3RD ROW OF SEATS THAT COULD BE CRACKED. WITH REPEATED ACTUATION OF THE LOCKING MECHANISM, THE CRACK COULD SPREAD TO THE POINT SUCH THAT THE SEAT BELT WOULD NO LONGER LOCK. Remedy: DEALERS WILL INSPECT THE OUTBOARD SEAT BELTS FOR SPECIFIC LOT NUMBERS AND REPLACE THE BELTS IF NECESSARY. GM IS ENCLOSING AN INSPECTION PROCEDURE FOR THE OWNERS TO USE OR THEY CAN HAVE THEIR DEALERS DO THE INSPECTIONS. OWNER NOTIFICATION BEGAN JULY 2, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT CHEVROLET AT 1-800-222-1020 OR GMC AT 1-800-462-8782.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain vehicles equipped with an 8.1L engine, the crankshaft position sensor may fail. If the sensor operates intermittently, the Service Engine Soon (SES) light may illuminate and the vehicle may run rough. In addition, the engine may stall, and if so, may re-start immediately or after a cool-down period. If the sensor becomes inoperable permanently, the engine will quit running and will not re-start. Engine stalling would result in lost propulsion which, in conjunction with traffic and road conditions, and the driver's reactions, could increase the risk of a crash. Correction: Dealers will replace the crankshaft position sensor.
Certain vehicles were built with fuel module reservoir assemblies that contain fuel pump wires and/or connectors that may overheat under certain operating conditions. Fuel pump wires that overheat may become exposed and result in one or more conditions; 1) If the ignition circuit wire is exposed and shorts to ground, the fuel pump fuse will blow, disabling the fuel pump and causing an engine stall or no-start condition. 2) If sufficient heat is conducted to the pass-through connector, a hole in the connector may result, which may cause the Service Engine Soon light to be illuminated during the emission system diagnostics routine. Fuel vapour (and in some limited cases liquid fuel) may leak out of the fuel tank through the hole in the connector body. 3) If the ignition circuit or ground wire is exposed and shorts to the fuel level sender card wires, inaccurate fuel level readings may result. Correction: Dealers will affect repairs.
Certain vehicles located in Ontario, Quebec, New Brunswick, Nova Scotia, Prince Edward Island, and Newfoundland & Labrador may experience unwanted Antilock Brake System (ABS) activation and increased stopping distances during low-speed brake application (less than 16 km/h and greater than 6 km/h). This condition does not set any ABS codes nor does it illuminate the ABS warning lamp. Correction: Dealers will remove the wheel speed sensor and thoroughly clean the wheel speed sensor mounting surface on the bearing, apply Zinc-X to the cleaned surface, grease the mounting surface, reinstall the wheel speed sensor, and check the output voltage to ensure the wheel speed signal is within specifications.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Crash-test ratings from NHTSA's New Car Assessment Program.
Source: NHTSA (US Department of Transportation) · US public domain
Certain vehicles fail to conform to CMVSS 209, seat belt assemblies. These vehicles have a condition where one or two sensors in the driver's and front seat passengers seat belt retractors may be inoperative. The seat belt retractors will lock when the belt webbing is extracted during a crash; however the mechanism that locks the seat belt retractor when the vehicle decelerates quickly, such as during heavy braking, may not restrain the occupant as intended during a crash, and could result in injury to the occupant. Correction update: None required as no effect on vehicle safety. See recall 04-158.
Certain vehicles have an internal component in the 2nd and 3rd row outboard seat belt retractor that could be cracked. With repeated actuation of the locking mechanism, the crack could spread to the point where the seat belt would no longer lock. In a crash, increased occupant injury could result from the no-lock condition. Correction: Dealers will inspect the outboard seat belts for specific lot numbers and replace the belts if necessary. GM is enclosing an inspection procedure for the owners to use or they can have their dealers do the inspections.
On certain Yukon Denali and Yukon XL Denali vehicles, the positive battery cable assembly that could come in contact with the steering shaft universal joint. This could eventually cause a wear through of the cable assembly convoluted conduit and cable insulation and result in intermittent electrical shorting. This could result in overheating and igniting of the cable insulation and conduit and a possible underhood fire. Correction: Dealers will inspect the positive battery cable for proper routing and reroute if necessary. Cable will also be inspected for wear of the conduit and cable insulation, and replaced if necessary.
Certain vehicles may have loose or missing rear wheelhouse plugs. Under certain operating conditions, exhaust gases can flow forward and accumulate in the rear wheelhouse. These exhaust gases could flow into the passenger compartment if the wheelhouse plug is missing or loose and may cause possible illness, unconsciousness or death. Correction: Dealers will inspect for loose or missing wheelhouse plugs, and install new plugs if necessary.