Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2001 Nissan Sentra, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
CERTAIN ANZO COMBINATION HEADLAMP ASSEMBLIES SOLD AS REPLACEMENT LAMPS FOR USE ON CERTAIN PASSENGER VEHICLES. SOME COMBINATION LAMPS ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS WHICH FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." Remedy: ANZO WILL NOTIFY OWNERS AND REPLACE THE HEADLAMPS FREE OF CHARGE. THE RECALL BEGAN MAY 9, 2006. OWNERS MAY CONTACT ANZO USA AT 909-468-3688.
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE COOLING HOLES IN THE STEEL WHEEL MAY HAVE BURRS ON THEIR EDGES AS A RESULT OF IMPROPER MANUFACTURING. THESE BURRS CAN CAUSE CRACKS AS THE VEHICLE IS BEING DRIVEN. CRACKS CAN PROPAGATE BETWEEN ADJACENT COOLING HOLES. IF ENOUGH CRACKS DEVELOP BETWEEN THE COOLING HOLES, THE WHEEL COULD FAIL AND SEPARATE FROM THE MOUNTING HUB WITHOUT PRIOR WARNING. Remedy: DEALERS WILL INSPECT FOR CRACKS AND REPLACE THE WHEEL IF CRACKS ARE DISCOVERED. OWNER NOTIFICATION WILL BE CONDUCTED IN TWO PHASES. THE FIRST MAILING BEGAN OCTOBER 1, 2001, ASKING OWNERS TO BRING THEIR VEHICLES IN TO A DEALER FOR INSPECTION OF THE WHEELS. ANY WHEELS WITH CRACKS WILL BE REPLACED. A SECOND OWNER NOTIFICATION WILL BEGIN IN EARLY DECEMBER, AT WHICH TIME NISSAN WILL HAVE AN ADEQUATE NUMBER OF REPLACEMENT WHEELS, REQUESTING OWNERS TO RETURN TO THEIR DEALERS TO HAVE THE WHEELS REPLACED. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT NISSAN AT 1-800-647-7261.
ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH THE QG18DE ENGINE OR QR25DE ENGINES, THE FOAM MATERIAL USED FOR THE INTERIOR LINING OF THE ELECTRONIC CONTROL MODULE (ECM) BOX EMITS SULFUR AS IT CURES. Remedy: DEALERS WILL REMOVE THE INSIDE LINING MATERIAL FROM THE ECM BOX. OWNER NOTIFICATION BEGAN ON DECEMBER 22, 2003. OWNERS SHOULD CONTACT NISSAN AT 1-800-647-7261.
ON CERTAIN PASSENGER VEHICLES, THE CIRCUIT BOARD FOR THE CRANK POSITION SENSOR OR CAM POSITION SENSOR MAY HAVE AN IMPROPER SOLDER JOINT DUE TO SOLDER DEFORMATION CAUSED BY HEAT STRESS ACCELERATED BY THE EXISTENCE OF FLUX RESIDUE DURING THE SOLDERING PROCESS. Remedy: DEALERS WILL REPLACE THE CRANK POSITION SENSORS. CAMSHAFT POSITION SENSOR(S), AND IN SOME CASES, THE VARIABLE TIMING CONTROL SENSOR(S). VEHICLES INVOLVED IN A PREVIOUS RECALL CAMPAIGN, 01V357, ARE ALSO INCLUDED IN THIS NEW CAMPAIGN. THE REPLACEMENT SENSORS USED IN THAT CAMPAIGN ARE ALSO AFFECTED. OWNER NOTIFICATION BEGAN ON DECEMBER 22, 2003. OWNERS SHOULD CONTACT NISSAN AT 1-800-647-7261 OR INFINITI AT 1-800-662-6200.
VEHICLE DESCRIPTION: CERTAIN PASSENGER VEHICLES FAIL TO COMPLY WITH REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE VEHICLES WERE MISSING TAMPERPROOF CAPS THAT PREVENT HORIZONTAL HEADLAMP ADJUSTMENT. Remedy: DEALERS WILL INSTALL A TAMPERPROOF CAP OVER THE HORIZONTAL ADJUSTMENT SCREW FOR BOTH HEADLAMPS. OWNER NOTIFICATION BEGAN JANUARY 14, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT NISSAN AT 1-800-647-7261.
ON CERTAIN ELECTRIC VEHICLES, THE FRONT SUSPENSION TRANSVERSE LINK'S BALL JOINT BRACKET MAY BREAK FROM STRESS CONCENTRATION AT A NOTCH CREATED BY SURFACE ROUGHNESS AND THE SHAPE OF THE MATERIAL CUT-LINE. Remedy: DEALERS WILL REPLACE THE BRACKET ON THESE VEHICLES. OWNER NOTIFICATION BEGAN DECEMBER 15, 2003. OWNERS SHOULD CONTACT NISSAN AT 1-800-647-7261.
VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH A 1.8 LITER ENGINE. THE ENGINE COULD STOP RUNNING WHILE BEING DRIVEN DUE TO A DEFECTIVE CRANK POSITION SENSOR. THIS COULD ALSO RESULT IN THE "SERVICE ENGINE SOON" WARNING LIGHT COMING ON OR REDUCED ENGINE POWER. Remedy: DEALERS WILL REPLACE THE CRANK POSITION SENSORS. OWNER NOTIFICATION BEGAN DECEMBER 10, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT NISSAN AT 1-800-647-7261.
VEHICLE DESCRIPTION: PASSENGER VEHICLES. ONE OR MORE OF THE THREE BOLTS USED TO ATTACH EACH FRONT SUSPENSION LOWER CONTROL ARM TO THE BODY ON THE LEFT AND RIGHT SIDES MAY NOT HAVE BEEN PROPERLY MANUFACTURED. Remedy: DEALERS WILL REPLACE THE LOWER CONTROL ARM ATTACHMENT BOLTS. OWNER NOTIFICATION BEGAN JUNE 30, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT NISSAN AT 1-800-647-7261.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain vehicles, the foam material used for the interior lining of the Engine Control Module (ECM) box out-gasses sulphur as it cures. If one of the resistors inside the ECM has a crack on the surface coating, the gas may cause corrosion of the resistor. This could cause the Malfunction Indicator Light to come on, poor drivability (idle instability, poor acceleration), or the engine to stop running without warning during vehicle operation. Correction: Dealer will remove the inside lining material from the ECM box.
On certain vehicles, the circuit board for the crank position sensor may have an improper solder joint. This could cause the Service Engine Soon warning light to come on, create a no start condition, cause reduced engine power, or cause the engine to stop running without warning during vehicle operation. Correction: Dealers will replace the crankshaft position sensor and both camshaft position sensors.
Certain passenger vehicles fail to comply with requirements of C.M.V.S.S. no. 108, "lamps, reflective devices, and associated equipment." these vehicles were missing tamperproof caps that prevent horizontal headlamp adjustment these caps are installed to prevent maladjustment of the headlamps. Correction: dealers will install a tamperproof cap over the horizontal adjustment screw for both headlamps.
Certain passenger vehicles equipped with a 1.8-liter engine. The engine could stop running while being driven due to a defective crank position sensor. This could also result in the "service engine soon" warning light coming on or reduced engine power. If the engine stops running while driving, this could result in a crash. Correction: dealers will replace the crank position sensors.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Crash-test ratings from NHTSA's New Car Assessment Program.
Source: NHTSA (US Department of Transportation) · US public domain
Certain passenger vehicles. Model year 2000-2001 Nissan Sentra vehicles manufactured from February 1, 2000, through June 26, 2001. The cooling holes in the steel road wheel may have burrs on their edge as a result of improper manufacturing. These burrs can cause stress concentration as the vehicle is being driven. Cracks can propagate these burrs between adjacent cooling holes. If enough cracks develop between the cooling holes, the wheel could fail and separate from the mounting hub without prior warning. Separation of the wheel from the vehicle while being operated could result in a vehicle crash, possibly resulting in personal injury or death. Correction: Dealers will replace all road wheels free of charge.
On certain vehicles, one or more of the three bolts used to attach each front suspension lower control arm to the body on the left and right sides may not have been properly heat treated when manufactured. The bolts could fracture, increasing the risk of a crash. Correction: Dealers will replace the lower control arm attachment bolts.
Certain vehicles do not comply with the requirements of CMVSS 101 - Location and Identification of Controls and Displays. Vehicles may be equipped with odometers that record in miles rather than kilometers, as required by the standard. Correction: Odometers that record in miles will be replaced with ones that record in kilometers.