Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2002 Ford Escape, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
Ford Motor Company (Ford) is recalling certain model year 2001-2008 Ford Escape and Mercury Mariner vehicles manufactured March 31, 2001, to September 1, 2009. The affected vehicles are equipped with either a 2.3L or 3.0L engine and have had their CD4E transmission replaced with remanufactured one that was rebuilt between June 11, 2015 through July 15, 2015. These service repair part transmissions have a shift lever bolt that may not be properly tightened. As a result, the shift control lever could disengage from the transmission without warning. Remedy: Ford will notify owners, and dealers will inspect the transmissions and either tighten the manual shift lever bolt or replace the manual shift lever assembly. These repairs will be performed free of charge. The recall began on October 23, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S28.
The Timken Company (Timken) is recalling certain aftermarket front wheel bearings, part number 510072, sold from January 22, 2015, to May 21, 2015, to be used as service parts on 2001-2012 Ford Escape, 2001-2011 Mazda Tribute, and 2005-2011 Mercury Mariner vehicles. The affected wheel bearings have incorrect dimensions of a 42mm bore, 76mm outer dimension, and 39mm width, instead of a 42mm bore, 78mm outer dimension and a 45mm width. Remedy: Timken has begun notifying distributors who will offer purchasers replacement wheel bearings, free of charge. The recall began on May 21, 2015. Owners may contact Timken customer service at 1-866-984-6536.
Ford Motor Company (Ford) is recalling certain model year 2001-2004 Escape vehicles manufactured October 22, 1999, through January 23, 2004, originally sold, or currently registered in, Connecticut, Delaware, Illinois, Indiana, Iowa, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, Wisconsin and the District of Columbia. These vehicles may experience excessive corrosion at the forward attachment of the lower control arm. Remedy: Ford will notify owners, and dealers will install a newly designed reinforcement cross-brace, free of charge. The recall began on May 30, 2014. Owners may contact Ford at 1-800-392-3673. Ford's number for this recall is 14S02.
Ford Motor Company is recalling certain model year 2001 through 2004 Escape vehicles equipped with 3.0L V6 engines and speed control manufactured from October 22, 1999, through January 23, 2004. Inadequate clearance between the engine cover and the speed control cable connector could result in a stuck throttle when the accelerator pedal is fully or almost-fully depressed. This risk exists regardless of whether or not speed control (cruise control) is used. Remedy: Ford will notify owners, and dealers will repair the vehicles by increasing the engine cover clearance, free of charge. The safety recall began August 3, 2012. Remedy parts are expected to be available in mid-August 2012. Until then dealers will disconnect the speed control cable as an interim remedy, if parts are not available at the time of an owner's service appointment. Owners may contact Ford at 1-866-436-7332.
FORD IS RECALLING CERTAIN MODEL YEAR 2001-2002 ESCAPE VEHICLES MANUFACTURED FROM OCTOBER 22, 1999, THROUGH JULY 19, 2002, EQUIPPED WITH A BRAKE MASTER CYLINDER RESERVOIR CAP THAT COULD LEAK BRAKE FLUID. IF BRAKE FLUID LEAKS FROM THE CAP, IT COULD COME IN CONTACT WITH THE ANTILOCK BRAKE SYSTEM (ABS) MODULE WIRING HARNESS CONNECTOR. Remedy: DEALERS WILL REPLACE THE BRAKE MASTER CYLINDER RESERVOIR CAP AND THE ABS ELECTRICAL SYSTEM WILL BE MODIFIED. AN INTERIM LETTER WAS MAILED ON JANUARY 20, 2012. DUE TO A PARTS DELAY, HOWEVER, THE REMEDY MAY NOT BE AVAILABLE CURRENTLY. IF PARTS ARE NOT AVAILABLE, FORD WILL INSTRUCT OWNERS TO PARK THEIR VEHICLES OUTSIDE UNTIL SUCH TIME AS PARTS BECOME AVAILABLE. OWNERS MAY CONTACT THE FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332. THIS RECALL CAMPAIGN IS RELATED TO 07V-156.
ON CERTAIN SPORT UTILITY VEHICLES EQUIPPED WITH ANTILOCK BRAKES (ABS), THE ABS MODULE CONNECTOR MAY HAVE MISSING OR DISLODGED WIRE SEALS. THIS CONDITION COULD ALLOW CONTAMINATION TO ENTER THE MODULE CONNECTOR, CREATING A POTENTIAL FOR AN ELECTRICAL SHORT. Remedy: DEALERS WILL INSPECT THE WIRE HARNESS CONNECTOR TO THE ABS MODULE FOR MISSING OR DISLODGED WIRE SEALS, AND REPAIR OR REPLACE THE HARNESS CONNECTOR AS APPROPRIATE. THE DEALER WILL ALSO INSPECT THE CONNECTOR ON THE ABS MODULE AND REPLACE IT IF IT IS FOUND TO BE CORRODED OR DAMAGED. THE RECALL BEGAN ON APRIL 23, 2007. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
ON CERTAIN SPORT UTILITY VEHICLES BUILT WITH 3.0L V6 ENGINES, THE ACCELERATOR CABLE MAY PREVENT THE THROTTLE FROM RETURNING TO THE IDLE POSITION. Remedy: DEALERS WILL REPLACE THE ACCELERATOR CABLE. THE RECALL BEGAN ON JANUARY 10, 2005. OWNERS SHOULD CONTACT FORD AT 1-866-436-7332.
CERTAIN CARDONE MASTER CYLINDERS WITH PART NUMBERS 10-2925, 10-2987, 10-2987MZA, 10-3083, 11-3015, 11-3042, 11-3044, 11-3045, 11-3047, 11-3064, AND 11-3156, AND WITH DATE CODES LOWER THAN DCA7078 SOLD AS REPLACEMENT EQUIPMENT FOR USE ON THE VEHICLES LISTED ABOVE. THE SEAL ON MASTER CYLINDER CAN FAIL AND LEAK BRAKE FLUID. Remedy: CARDONE WILL NOTIFY OWNERS AND OFFER TO REPURCHASE ANY DEFECTIVE MASTER CYLINDERS. THE RECALL BEGAN DURING APRIL 2007. OWNERS CAN CONTACT CARDONE AT 1-800-777-4780.
CERTAIN 2004-2005 SPORT UTILITY VEHICLES AND CERTAIN 2001-2003 SPORT UTIITY VEHICLE HAVING REAR LIFTGATE COMPONENTS SERVICED WITH 2004 EQUIVALENT COMPONENTS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 206, 'DOOR LOCKS AND DOOR RETENTION COMPONENTS.' THE REAR LIFTGATE LATCHING SYSTEM DOES NOT MEET THE INERTIA LOAD REQUIREMENT IN ONE DIRECTION. Remedy: DEALERS WILL REPLACE THE REAR LIFTGATE LATCH RELEASE ROD, THE RELEASE ROD ATTACHMENT CLIP AND THE DOOR HANDLE RETURN SPRING. THE RECALL BEGAN ON MARCH 31, 2005. OWNERS SHOULD CONTACT FORD AT 1-800-392-3673.
ON CERTAIN SPORT UTILITY VEHICLES EQUIPPED WITH 3.0L V6 ENGINES, DURING DECELERATION, THE ENGINE CAN STALL. Remedy: DEALERS WILL REPROGRAM THE POWER CONTROL MODULE (PCM) WITH THE APPROPRIATE CALIBRATION. OWNER NOTIFICATION BEGAN ON APRIL 21, 2004. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-800-392-3673.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
A safety defect may exist in vehicles in which remanufactured automatic transmissions were installed as service replacement parts. The shift lever bolt may not have been torqued to the proper torque specification. If the improperly torqued shift level bolt loosens and backs out, the shift lever may disengage from the transmission without warning, and the transmission may not respond to the shifter selection movement by the operator. This could result in the loss of transmission gear selection, and possible unintended vehicle movement, which would increase the risk of a crash causing injury and/or property damage. Correction: Dealers will inspect, and if necessary, replace the shift lever assembly and/or the shift level bolt torqued to the proper specification.
On certain vehicles registered and operated in areas where road salt is used on the roadways during winter months for extended time periods (Ontario, Quebec, New Brunswick, Nova Scotia, Prince Edward Island and Newfoundland-Labrador), the forward attachment point for the lower control arm may separate from the vehicle's subframe. This could affect vehicle handling and increase the risk of a crash causing injury and/or property damage. Correction: Dealers will install a newly designed reinforcement cross-brace.
On certain vehicles equipped with a 3.0L V6 engine and speed control, inadequate clearance between the engine cover and the speed control cable connector could result in a stuck throttle when the accelerator pedal is fully or almost-fully depressed. A stuck throttle may result in very high vehicle speeds and make it difficult to slow or stop the vehicle if the transmission is not shifted into neutral. This could result in a crash causing property damage and/or personal injury. Correction: Dealers will replace the rear engine cover fastener, which will raise the cover in the area of the speed control cable to provide adequate clearance between the cover the speed control cable connector.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Crash-test ratings from NHTSA's New Car Assessment Program.
Source: NHTSA (US Department of Transportation) · US public domain
Certain vehicles may have been originally equipped with a brake master cylinder reservoir cap that could leak. If brake fluid leaks from the cap, it could come in contact with the ABS module wiring harness connector. The same vehicles were previously involved in campaign 2007107 to address potentially missing or misplaced seals in the wiring harness connector to the ABS module electronic control unit. If this repair wasn’t done correctly, brake fluid leaking from the reservoir cap could corrode the ABS module electrical connector. This could result in vehicle fire causing property damage and/or personal injury. Correction: Dealers will replace the brake master cylinder reservoir cap and modify the ABS electrical system. Note: Owners are advised to park the vehicle outdoors until the remedy is applied.
On certain vehicles, the electrical wiring connector to the ABS module may have been manufactured incorrectly. Over time, contaminants can enter the ABS electrical connector interface and corrode the terminals. This could cause the ABS warning indicator to illuminate, an open fuse, and in some instances, smoking, melting or burning of the electrical connector, with the potential for a fire while the vehicle is unattended. In addition, ABS function may be lost. Correction: Dealers will inspect and, if required, repair the wiring connector.
On certain vehicles equipped with 3.0L V6 engines, the accelerator cable's inner liner may, over time, migrate out of the conduit at the dash panel fitting during vehicle operation. The liner may migrate to the point that it contacts the accelerator pedal arm. Under these conditions the liner may prevent the pedal from fully returning, which may not allow the throttle body to fully return to the "idle" position. Typically the condition results in a progressive increase in the "idle" speed if liner migration continues over time, but may cause a more sudden increase if a greater portion of the cable moves at one time. An unexpected increase in "idle" speed may result in longer than expected stopping distances, which could potentially lead to a crash. Correction: Dealers will replace the accelerator cable.
On certain vehicles equipped with a 3.0L V6 engine, during deceleration at vehicle speeds below 64 km/h, the engine may stall due to an excessively rich fuel-air mixture. Correction: Dealer will reprogram the Powertrain Control Module.