Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2002 International 4300, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
CERTAIN TRUCKS EQUIPPED WITH ENGINE STARTERS (CODE 08WWN OR 08WWP) BUILT BY LEECE-NEVILLE. THESE STARTERS HAVE A DEFECTIVE TERMINAL ADAPTER STUD. THE STUD IS USED ONLY AT THE POSITIVE BATTERY CONNECTION TO THE STARTER SOLENOID. IT WAS DESIGNED TO BE SCREWED ON OVER THE EXISTING STUD TO INCREASE THE STUD DIAMETER TO ACCOMMODATE THE LARGER SIZE OF THE POSITIVE BATTERY CABLE TERMINAL. THE ADAPTER STUD WAS WEAKENED WHEN THE HOLE WAS DRILLED TOO DEEP. Remedy: DEALERS WILL REPLACE THE ADAPTER STUD. OWNER NOTIFICATION BEGAN APRIL 15, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT INTERNATIONAL AT 1-800-448-7825.
CERTAIN HEAVY DUTY TRUCKS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS." THE PRIMARY AND SECONDARY AIR SUPPLY HOSES FROM THE FOOT VALVE TO THE PRIMARY AND SECONDARY AIR TANKS WERE IMPROPERLY ROUTED AT THE TANK. Remedy: DEALERS WILL INSPECT AND REPAIR VEHICLES. OWNER NOTIFICATION WILL BE COMPLETED BY OCTOBER 3, 2003. OWNERS WHO TAKE THEIR VEHICLE TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT INTERNATIONAL AT 1-800-448-7825.
ON CERTAIN SCHOOL AND TRANSIT BUSES BUILT WITH BOSCH ZERO OFFSET PIN SLIDE (ZOPS) HYDRAULIC DISC BRAKES, THE ZOPS HYDRAULIC DISC BRAKES MAY EXPERIENCE CALIPERS STICKING IN THE APPLIED POSITION, WHICH CAN RESULT IN EXCESSIVE OR ABNORMAL HEAT GENERATION AT ONE OR MORE OF THE BRAKES. Remedy: INTERNATIONAL WILL NOTIFY ITS CUSTOMERS AND REPAIR THE BUSES FREE OF CHARGE. THE RECALL BEGAN OCTOBER 29, 2004.
ON CERTAIN TRUCKS, THE COTTER PIN THAT GOES THROUGH THE DRAG LINK BALL STUD AT THE CONNECTION TO THE PITMAN ARM IS MISSING. THIS PIN PREVENTS THE CASTLE NUT FROM LOOSENING. Remedy: DEALERS WILL INSPECT THE VEHICLE AND INSTALL A COTTER PIN IF IT IS MISSING. OWNER NOTIFICATION BEGAN APRIL 15, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT INTERNATIONAL AT 1-800-448-7825.
ON CERTAIN HEAVY DUTY TRUCKS EQUIPPED WITH IROS REAR AIR SUSPENSIONS, DURING ASSEMBLY, FOUR BOLTS AND NUTS HOLDING THE MAIN SUPPORT MEMBER BUSHING BAR PINS TO THE MAIN SUPPORT MEMBER HANGERS WERE INCORRECTLY TIGHTENED. Remedy: DEALERS WILL INSTALL FOUR NEW NUTS AND BOLTS AND TIGHTEN TO SPECIFICATION. OWNER NOTIFICATION BEGAN MARCH 15, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT INTERNATIONAL AT 1-800-448-7825.
CERTAIN HEAVY DUTY TRUCKS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 104, "WINDSHIELD WIPING AND WASHING SYSTEMS." DUE TO THE DESIGN OF THE WINDSHIELD WASHER PUMP MOTOR CIRCUIT, THE SYSTEM'S ABILITY TO FUNCTION IS IMPAIRED WHEN IT IS FULL OF FROZEN WATER AND THE PUMP MOTOR SHAFT IS LOCKED OR FROZEN (CANNOT ROTATE). Remedy: DEALERS WILL INSTALL A NEW 10 AMP FUSE IN PLACE OF THE 5 AMP FUSE AND A NEW 10 AMP LABEL WILL BE PLACED OVER THE ORIGINAL 5 AMP DESIGNATION ON THE FUSE PANEL LABEL. OWNER NOTIFICATION BEGAN ON JUNE 27, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT INTERNATIONAL AT 1-800-448-7825.
VEHICLE DESCRIPTION: TRUCKS. AN INCORRECT GRADE 5 FLANGE-NUT WAS INSTALLED IN PLACE OF A GRADE 8 NUT AND FLAT WASHER ON THE YOKE PINCH BOLT THAT HOLDS THE CONNECTION BETWEEN THE LOWER END OF THE I-SHAFT AND THE STEERING GEAR. Remedy: DEALERS WILL REPLACE THE GRADE 5 PINCH BOLT NUT WITH THE CORRECT GRADE 8 NUT AND WASHER ON ALL VEHICLES. OWNER NOTIFICATION BEGAN DECEMBER 17, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT INTERNATIONAL AT 1-800-448-7825.
ON CERTAIN MEDIUM AND HEAVY DUTY TRUCKS BUILT WITH DRIVELINE PARKING BRAKE CODES 04GAR, THE PARKING BRAKE ASSEMBLY MAY NOT HOLD THE VEHICLE IN POSITION WHEN SET. FACTORS CONTRIBUTING TO THIS POSSIBILITY ARE AS FOLLOWS: (1) CRACKED OR BROKEN CAMS; (2) LOOSE OR BROKEN ANCHOR BOLTS; (3) INITIAL SHOE DIAMETER NOT SET PROPERLY DURING ASSEMBLY, WHICH CAN LEAD TO PROGRESSIVE COMPONENT DAMAGE; (4) BENT ADJUSTER LEVERS THAT CANNOT FUNCTION; OR (5) AUTOMATIC ADJUSTER CABLES THAT ARE DISCONNECTED. Remedy: DEALERS WILL REPLACE THE CAM, LEVER, AND BOLT. OWNER NOTIFICATION BEGAN DECEMBER 30, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT INTERNATIONAL AT 1-800-448-7825.
ON CERTAIN HEAVY DUTY TRUCKS EQUIPPED WITH MANUAL TRANSMISSIONS, LOWER CLUTCH RODS WITH TURNBUCKLES ARE FAILING FROM FATIGUE NEAR THE TURNBUCKLE DUE TO BENDING FORCES EXPERIENCED DURING EACH CLUTCH PEDAL CYCLE. Remedy: DEALERS WILL REPLACE THE CLUTCH ROD ASSEMBLY WITH A SOLID ROD DESIGN THAT DOES NOT HAVE A TURNBUCKLE. OWNER NOTIFICATION BEGAN JULY 19, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT INTERNATIONAL AT 1-800-448-7825.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain vehicles, the Bosch Zero Offset Pin Slide (ZOPS) hydraulic disc brakes may experience calipers sticking in the applied position, which can result in excessive or abnormal heat generation at one or more of the brakes. In bus applications, the combination of the following factors may collectively result in an unreasonable risk to motor vehicle safety: potential fire at a wheel end, high incident rates of stuck calipers, and evacuation and containment concerns relating to multiple passengers. Correction: Dealers will affect repairs. This is an expansion of Recall 2003053.
On certain vehicles, the primary and secondary air supply hoses from the foot valve to the air tanks were reversed at the tanks. If the primary air circuit is damaged, the brakes will not apply when the brake pedal is depressed, potentially causing a vehicle crash without warning and possibly resulting in property damage, personal injury or death. Correction: Dealer will inspect all suspect vehicles and repair incorrect air plumbing.
On certain vehicles, the parking brake assembly may not hold the vehicle in position when set. Factors contributing to this possibility are as follows: 1. Cracked or broken cams; 2. Loose or broken anchor bolts; 3. Initial shoe diameter not set properly during assembly, which can lead to progressive component damage; 4. Bent adjuster levers that cannot function; 5. Automatic adjuster cables that are disconnected. If this parking brake does not function properly, the vehicle may begin to roll, without warning, after the parking brake lever has been set and could cause an accident, possibly resulting in property damage, personal injury or death. Correction: Dealers will replace the cam, lever and bolt on all affected vehicles.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Certain vehicles clutch rods are failing from fatigue near the turnbuckle due to bending moments experienced during each pedal cycle. The clutch rod can break without warning and make it difficult to shift and if the clutch rod breaks while the vehicle is stopped, the vehicle may lunge unexpectedly in the direction of the selected gear. Correction: Dealers will replace the clutch rod assembly with a solid rod design that does not have a turnbuckle.
Certain trucks equipped with engine starters (code 08wwn or 08wwp) built by Leece-Neville. These starters have a defective terminal adapter stud. The stud is used only at the positive battery connection to the starter solenoid. It was designed to be screwed on over the existing stud to increase the stud diameter to accommodate the larger size of the positive battery cable terminal. The adapter stud was weakened when the hole was drilled too deep. This could lead to a direct electrical short to the batteries. If the stud breaks off, the positive battery cable could short directly to ground, which can generate heat and sparks causing a fire. Correction: Dealers will replace the adapter stud.
On certain trucks the cotter pin that goes through the drag link ball stud at the connection to the pitman arm is missing. This pin prevents the castellated nut from loosening. If the nut loosens and comes completely off the drag link ball stud, the drag link could detach resulting in a loss of steering control. Correction: Dealers will inspect the vehicle and have a cotter pin installed if found to be missing.
Certain heavy-duty trucks equipped with (IROS) rear air suspensions. During assembly, four bolts and nuts holding the main support member bushing bar pins to the main support member hangers were incorrectly tightened. The nuts could work loose or fall off allowing the bolts to fatigue and fail the connection between a main support member bushing and a main support member frame hanger. Separation of the main support member assembly from the frame mounted hanger bracket could result increasing the risk of sudden loss of control of the vehicle. Correction: Dealers will install four new nuts and bolts and tighten to specification.
On certain vehicles the yoke pinch bolt connection from the steering shaft to the steering gear was assembled with an incorrect bolt. Correction: dealers will replace the bolt.
Certain vehicles fail to meet C.M.V.S.S. 104. During the system frozen test the washer pump fuse failed. Correction: Dealer will replace the 5 amp fuse with a 10 amp fuse and install a new 10 amp label over the original 5 amp designation on the fuse panel label.
Certain heavy-duty trucks. These vehicles could experience a loss of the low beam headlights, the high beam headlights, or both. A software problem within the electrical system controller (esc) can cause the circuit for the low beam or the circuit for the high beam headlights to fuse or open, resulting in loss of either the low or high beam headlights or possibly even both. A headlight fusing condition could occur without warning to the driver and potentially leave the driver in a blackout situation while operating the vehicle in the dark. Correction: dealers will reprogram the esc.