Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2003 Volvo VHD, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
Volvo is recalling certain model year 2002-2013 VHD and VN trucks, manufactured from August 4, 2000, through June 22, 2012, and equipped with bench passenger seats. The seat belt d-ring weld may not be sufficient enough to meet the seat belt pull test. Therefore, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard No. 210, "Seat Belt Assembly Anchorages." Remedy: Volvo Trucks of America will notify owners, and dealers will replace the suspected d-ring, free of change. The safety recall began on May 10, 2013. Owners may contact Volvo at 1-336-393-2000.
VOLVO TRUCKS IS RECALLING 127,764 MY 2001-2008 VHD, VNL, VNM, AND MY 2005-2008 VT TRUCKS. A SEAL MAY FAIL ALLOWING WATER AND CONTAMINANTS TO SEEP INTO THE WINDSHIELD WIPER MOTOR. Remedy: VOLVO WILL REPLACE THE WIPER MOTOR FREE OF CHARGE. SINCE THIS RECALL INVOLVES A LARGE NUMBER OF VEHICLES, VOLVO WILL RELEASE THE RECALL IN STAGES AS PARTS ARE RECEIVED. PRIORITY WILL BE GIVEN TO THE VEHICLES LOCATED IN THE REGIONS/STATES THAT HAVE A CORROSIVE ENVIRONMENT. THE RECALL BEGAN ON SEPTEMBER 30, 2009. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
ON CERTAIN HEAVY DUTY TRUCKS, THE CIRCUIT PROTECTION (I.E. AUTOMATIC CIRCUIT BREAKERS) USED TO PROTECT THE VEHICLE LIGHTING SYSTEM MAY NOT PROVIDE ADEQUATE PROTECTION. Remedy: DEALERS WILL REPLACE THE CIRCUIT BREAKERS WITH FUSES. THE RECALL BEGAN ON FEBRUARY 25, 2008. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
ON CERTAIN TRUCKS EQUIPPED WITH D12D ENGINES, THE EXHAUST GAS RECIRCULATION (EGR) COOLER INLET PIPES OR THE PIPES THAT CONNECT THE EGR VALVES TO THE COOLER MAY CRACK OR BREAK. Remedy: DEALERS WILL INSPECT AND REPAIR THE EGR COOLER PIPES AS REQUIRED AND INSTALL A HEAT SHIELD FREE OF CHARGE. AN INTERIM OWNER LETTER WAS MAILED ON FEBRUARY 17, 2006, TO ADVISE ON PRECAUTIONS THAT THE OWNER CAN TAKE UNTIL PARTS BECOME AVAILABLE. OWNERS ARE BEING NOTIFIED STARTING MARCH 3, 2006, THAT PARTS ARE NOW AVAILABLE. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
ON CERTAIN TRUCKS, THE WHEEL SPACER MAY BECOME DISTORTED FROM HEAT WHICH POTENTIALLY COULD LEAD TO A LOSS OF CLAMP THAT MAY RESULT IN LOOSE WHEEL NUTS. Remedy: DEALERS WILL REPLACE THE WHEEL SPACERS AND THE WHEEL EQUIPMENT (WHEELS,STUDS, AND HUB) WILL BE INSPECTED FOR DAMAGE AND REPLACED IF NECESSARY FREE OF CHARGE. THE RECALL BEGAN ON JUNE 26, 2006. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
CERTAIN HEAVY DUTY CLASS 8 TRUCKS EQUIPPED WITH AN OPTIONAL TWO-MAN PASSENGER BENCH SEAT FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 210, "SEAT BELT ASSEMBLY ANCHORAGES." ON THE TWO-MAN PASSENGER BENCH SEAT INBOARD (CENTER) POSITION, SEAT BELT D-RING MOUNTING BRACKET WELDNUT, THE WELD IS NOT SUFFICIENT TO MEET THE SEAT BELT PULL REQUIREMENTS . Remedy: DEALERS WILL REPLACE THE SEAT BELT D-RING MOUNTING BRACKET. OWNER NOTIFICATION BEGAN ON APRIL 7, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT VOLVO TRUCKS AT 1-800-528-6586.
ON CERTAIN HEAVY DUTY TRUCKS EQUIPPED WITH JOST INTERNATIONAL JSK 37U SERIES FIFTH WHEELS, A FATIGUE CRACK CAN DEVELOP IN THE BRACKET PIN WELD UNDER CERTAIN LOADING CONDITIONS. Remedy: DEALERS WILL REPLACE THE BRACKET PINS AND REPAIR INSTRUCTIONS FREE OF CHARGE. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT JOST INTERNATIONAL AT 616-846-7700 OR BY EMAIL TO RECALL@JOSTINTERNATIONAL.COM OR VOLVO TRUCK AT 800-528-6586.
CERTAIN TRUCKS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 207, 'SEATING SYSTEMS.' THE BENCH SEAT, AS INSTALLED, DOES NOT THE SEAT PULL REQUIREMENTS OF THE STANDARD. Remedy: DEALERS WILL REPLACE THE PASSENGER SIDE BENCH SEAT WITH A DIFFERENT BRAND OF SEAT. THE RECALL BEGAN NOVEMBER 1, 2004. OWNERS SHOULD CONTACT VOLVO TRUCKS AT 1-800-528-6586.
ON CERTAIN TRUCKS EQUIPPED WITH VALEO WIPER SYSTEMS, THE WIPER MOTOR MAY BE SUSCEPTIVE TO SALT INTRUSION THAT COULD POSSIBLY LEAD TO A CONDITION WHERE THE CONNECTOR OVERHEATS TO A POINT WHERE THE CONNECTOR COULD IGNITE. Remedy: DEALERS WILL INSPECT AND REPLACE THE CONNECTOR PLATE ON THE WINDSHIELD WIPER MOTOR. PHASE 2 OF THE RECALL BEGAN ON NOVEMBER 1, 2004. OWNERS SHOULD CONTACT VOLVO TRUCKS AT 1-800-528-6586.
ON CERTAIN HEAVY-DUTY CLASS 8 TRUCKS, THE PINCH BOLT ATTACHING THE STEERING DRAG LINK TO THE PITMAN ARM MAY NOT HAVE BEEN SUFFICIENTLY TIGHTENED. Remedy: DEALERS WILL INSTALL A NEW PINCH BOLT AND TIGHTEN TO THE REQUIRED TORQUE. OWNER NOTIFICATION IS EXPECTED TO BEGIN DURING MARCH 2004. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT VOLVO TRUCKS AT 1-800-528-6586.
ON CERTAIN HEAVY-DUTY CLASS 8 TRUCKS, THE ASSEMBLED ENGINE PRE-HEATER JUMPER WIRING HARNESS WAS INCORRECTLY ASSEMBLED. Remedy: DEALERS WILL REPAIR THE AFFECTED CIRCUITS IN THE JUMPER WIRING HARNESS CONNECTOR. OWNER NOTIFICATION IS EXPECTED TO BEGIN DURING MARCH 2004. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT VOLVO TRUCKS AT 1-800-528-6586.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Certain vehicles equipped with a snowplow preparation kit may fail to comply with the requirements of Canada Motor Vehicle Safety Standard (CMVSS) 108 - Lighting System and Retroreflective Devices. The snowplow headlamps can be turned on without other exterior lights, and the high beam indicator does not work when the snowplow high beams are turned on, which is contrary to the requirements of the standard. This could allow the vehicle to be operated with the snowplow headlamps on and marker and tail lamps off, making the vehicle harder to see and potentially increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will update vehicle software to correct the non-compliance.
Certain vehicles may fail to conform to Canada Motor Vehicle Safety Standard 210 – Seatbelt Assembly Anchorages. The weld used to secure the nut to the center-passenger seatbelt D-ring mounting bracket may not be sufficient to meet the strength requirements of the Standard. Failure of the seatbelt D-ring anchorage to restrain the occupant would increase the risk of personal injury during a crash. Correction: Dealers will replace the D-ring for the middle seating position.
On certain vehicles, the windshield wiper motor may be susceptible to water intrusion, which could result in an electrical short circuit and a fire. This could cause property damage, personal injury or death. Correction: Dealers will affect repairs.
On certain trucks, the automatic circuit breakers used to protect the vehicle lighting system may not provide adequate protection. If a short circuit occurs, components and wiring may be subject to overheating, which could result in a vehicle fire, causing property damage and/or personal injury or death. Correction: Dealers will replace the circuit breakers with fuses.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
On certain vehicles, the material specification of the wheel spacer may not be suitable for some applications where severe operating conditions can result in degradation of the wheel spacer. This could lead to a loss of clamp load, which may result in loose wheel nuts. If the wheel nuts loosen for any reason, damage to the wheel studs and/or wheel may occur, which if left uncorrected, may lead to complete separation of the wheel(s) from the vehicle. Correction: Dealers will replace the wheel spacers and inspect and replace (as required) the wheels and wheel equipment.
On certain vehicles, the Exhaust Gas Recirculation (EGR) cooler inlet pipes and/or the pipes that connect the EGR valves to the cooler may fail (crack or break). If the pipes or the cooler inlet pipes fail and are left untreated, the air cleaner and inner fender may be subject to hot exhaust gases, which could potentially lead to a fire. Correction: Dealers will inspect the EGR cooler pipes and install a heat shield.
On certain vehicles, the windshield wiper motor may be susceptible to salt spray intrusion which could cause the wiper motor connector to overheat and ignite. A vehicle fire could result in property damage, personal injury or death. Correction: Dealers will replace the connector plate on the windshield wiper motor.
Certain vehicles do not comply with the requirements of CMVSS 207. The Isringhausen brand two man bench seat installation does not withstand forces required by the standard. Correction: Dealers will replace the Isringhausen seat with a different brand seat.
On certain vehicles, the pinch bolt that attaches the drag link to the pitman arm may not have been tightened to the required torque value. This condition could allow the pinch bolt to loosen and allow the drag link and pitman arm to separate resulting in uncontrollable steering and potential for a vehicle crash. Correction: Dealer will install a new pinch bolt and tighten to the required torque.
On certain vehicles, an incorrectly assembled engine pre-heater jumper wiring harness may allow continuous electrical power to the engine pre-heater power relays if the fuse in the harness opens. This condition could cause the engine pre-heater to overheat resulting in damage to the pre-heater and other engine heat sensitive components near the pre-heater. Correction: Dealer will inspect and where required re-index affected circuits in the pre-heater jumper wiring harness connector.
On certain vehicles equipped with an optional two man passenger bench seat. The weld on the D-ring mounting bracket for the seat belt at the bench seat inboard (center) position may not be sufficient to meet the requirements of CMVSS 210. Correction: Dealer will replace the non-complying seat belt D-ring mounting bracket.