Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2004 Buick Rainier, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
ON CERTAIN TRUCKS AND SPORT UTILITY VEHICLES, THE DRIVER WISHING TO SIGNAL A TURN BY MOVING THE DIRECTIONAL SIGNAL LEVER, (UP OR DOWN) MAY CAUSE THE FRONT MARKER/TURN LIGHTS AND REAR TURN LIGHTS TO FLASH IN A MANNER SIMILAR TO HAZARD WARNING, RATHER THAN FLASHING ON THE DESIRED SIDE ONLY. Remedy: DEALERS WILL REPLACE THE SUSPECT FLASHER MODULES WITH A NEW FLASHER MODULE DESIGNED WITH SEALED RELAYS AND MORE DURABLE CONTACT MATERIAL INSIDE OF THE RELAYS FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 4, 2005. ISUZU BEGAN MAILING OWNER LETTERS ON AUGUST 4, 2005. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438, GMC AT 1-866-996-9463, ISUZU AT 1-800-255-6727, BUICK AT 1-866-608-8080, AND OLDSMOBILE AT 1-800-630-6537.
ON CERTAIN SPORT UTILITY VEHICLES, VIBRATION AND HEAT MAY CAUSE THE TAIL LAMP/STOP LAMP BULB TO LOOSEN IN ITS SOCKET. IF THIS OCCURS, THE BULB MAY FLICKER AND EVENTUALLY BECOME INOPERATIVE. Remedy: DEALERS WILL INSPECT THE TAIL LAMP/STOP LAMP ASSEMBLIES, AND IF NECESSARY, REPLACE THEM. THE RECALL BEGAN ON NOVEMBER 22, 2004. OWNERS SHOULD CONTACT CHEVROLET AT 1-800-630-2438, OLDSMOBILE AT 1-800-630-6537, BUICK AT 1-866-608-8080, OR GMC AT 1-866-996-9463.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Issue: This recall is for aftermarket replacement rear window glass produced by Vitro Automotriz. Certain rear window glass may not have been properly tempered. If the window breaks, the glass may separate into large pieces instead of very small ones. Note: This is a voluntary recall that is not being conducted under the requirements of the Motor Vehicle Safety Act. Safety Risk: Glass that breaks in to large pieces could create a risk of injury. Corrective Actions: The company will notify consumers by mail and instruct them to inspect the designation code marked on the rear window glass. Products affected by this recall have the designation “DOT 287” along with the lettering “VMR” (Replacement Market) and a date code that is before July 2019. This information is printed on the bottom corner of the glass. Consumers should contact Vitro's customer service at 1-412-995-6457 or argbacklites@vitro.com to arrange for replacement of the glass.
On certain vehicles, the directional/hazard signals may not operate as designed. Actuation of the turn signal or hazard lights will cause them to illuminate and remain illuminated (not flash as intended). Drivers may not be able to clearly signal their intentions to turn, change travel lanes or potentially warn others of an impaired vehicle operating condition. Correction: Dealers will replace the turn signal/hazard flasher module.
On certain vehicles, vibration and heat may cause the tail lamp/stop lamp bulb to loosen in its socket. If this occurs, the bulb may flicker and eventually become inoperative. The loss of one or both of the tail lamps/stop lamps could reduce the vehicle's visibility to following drivers and fail to warn others that the vehicle is braking and/or is stopped, which could lead to a vehicle crash. Correction: Dealers will inspect the tail lamp/stop lamp assemblies and, if necessary, replace them.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Crash-test ratings from NHTSA's New Car Assessment Program.
Source: NHTSA (US Department of Transportation) · US public domain
On certain vehicles, the brake hoses are not labelled with a designation that identifies the manufacturer of the assembly as required by CMVSS 106. This non-compliance has no effect on the performance of the involved brake hose assemblies. Correction: Since this does not pose a safety risk, no corrective action is required.