Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2004 Cadillac SRX, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
This defect can affect the safe operation of the airbag system. Until this recall is performed, customers should remove all items from their key rings, leaving only the ignition key. The key fob (if applicable), should also be removed from the key ring. General Motors LLC (GM) notified the agency on July 2, 2014 that they are recalling 554,328 model year 2003-2014 Cadillac CTS vehicles manufactured August 16, 2001, to April 28, 2014, and 2004-2006 Cadillac SRX vehicles manufactured March 20, 2003, to August 11, 2006. In these models, the weight on the key ring and/or road conditions or some other jarring event may cause the ignition switch to move out of the run position, turning off the engine. Remedy: GM will notify owners, and dealers will install two key rings and an insert in the key slot or a cover over the key head on all ignition keys, free of charge. The recall began on September 15, 2014. Owners may contact Cadillac customer service at 1-800-458-8006. GM's number for this recall is 14172.
GM IS RECALLING 17,301 MY 2004 CADILLAC SRX VEHICLES EQUIPPED WITH AN AUTOMATIC TRANSMISSION. SOME OF THESE VEHICLES HAVE A CONDITION IN WHICH THE TRANSMISSION SHIFT LEVER CAN BE MOVED FROM THE "PARK" POSITION WITH THE IGNITION "ON" AND WITHOUT THE OPERATOR DEPRESSING THE BRAKE PEDAL OR, IN SOME CASES, THE SHIFTER CAN BE MOVED FROM THE "PARK" POSITION WITH THE IGNITION TURNED OFF. Remedy: DEALERS WILL REPLACE THE PAWL STOPPER AND A BUSHING WITHIN THE SHIFTER ASSEMBLY FREE OF CHARGE. THE RECALL BEGAN ON DECEMBER 3, 2008. OWNERS MAY CONTACT CADILLAC AT 1-800-982-2339 OR THROUGH THEIR WEBSITE AT <A HREF=HTTP://WWW.GMOWNERCENTER.COM>HTTP://WWW.GMOWNERCENTER.COM</A> .
CERTAIN PASSENGER VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 124, 'ACCELERATOR CONTROL SYSTEMS.' IF ONE OF THE TWO ACCELERATOR PEDAL RETURN SPRINGS FAILS AND THE TEMPERATURE IS -22 DEGREES F TO -40 DEGREES F, THE ENGINE MAY NOT RETURN TO IDLE WITHIN THREE SECONDS, AS REQUIRED. Remedy: DEALERS WILL REPLACE THE ACCELERATOR PEDAL ASSEMBLY. THIS RECALL BEGAN ON MARCH 8, 2005. OWNERS MAY CONTACT CADILLAC AT 1-866-982-2339 OR PONTIAC AT 1-800-620-7668.
ON CERTAIN PASSENGER VEHICLES, AN INTERACTION BETWEEN THE SENSING AND DIAGNOSTIC MODULE AND VEHICLE'S ELECTRICAL SYSTEM MAY CAUSE THE DRIVER'S FRONTAL AIR BAG AND/OR ROOF-MOUNTED SIDE IMPACT AIR BAG TO DEPLOY WHEN THE IGNITION KEY IS TURNED TO THE "ON" POSITION. Remedy: DEALERS WILL REPLACE THE SENSING AND DIAGNOSTIC MODULE FREE OF CHARGE. THE RECALL BEGAN ON MAY 20, 2005. OWNERS MAY CONTACT CADILLAC AT 1-866-982-2339.
ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH ALL WHEEL DRIVE, THE ANTILOCK BRAKE SYSTEM (ABS) MAY IMPROPERLY TEMPORARILY ISOLATE THE DRIVER FROM THE FOUNDATION BRAKE SYSTEM FOR A MAXIMUM OF 1.25 SECONDS. Remedy: DEALERS WILL REPROGRAM THE ABS TRACTION CONTROL SYSTEM CONTROLLER. OWNER NOTIFICATION BEGAN ON MAY 10, 2004. OWNERS SHOULD CONTACT CADILLAC AT 1-866-982-2339.
CERTAIN PASSENGER AND SPORT UTILITY VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 207, "SEATING SYSTEMS." ONE OR BOTH FRONT ANCHOR TABS FOR THE FRONT BUCKET SEATS ARE NOT ENGAGED IN THE FLOOR PAN REINFORCEMENT SLOTS. A SEAT WITH ONLY ONE TAB ENGAGED OR NEITHER ENGAGED WOULD NOT MEET THE STATIC REARWARD LOADING TEST REQUIREMENTS OF THE STANDARD. Remedy: DEALERS WILL ENSURE THAT BOTH FRONT ANCHOR TABS ARE FULLY SEATED IN THE FLOOR PAN REINFORCEMENT SLOTS. OWNER NOTIFICATION BEGAN SEPTEMBER 19, 2003. OWNERS SHOULD CONTACT GM AT 1-800-458-8006.
ON CERTAIN PASSENGER VEHICLES INVOLVED IN THIS CAMPAIGN, THE LOWER CONTROL ARM BALL STUD NUT/WASHER ASSEMBLIES WITH WASHERS WERE MADE OF THE WRONG MATERIAL. THE WASHERS MAY FRACTURE AND BECOME LOOSE OR FALL AWAY FROM THE VEHICLE, REDUCING CLAMP LOAD. SEPARATION OF THE CONTROL ARM BALL STUD AND STEERING KNUCKLE, DUE TO DISENGAGEMENT OF THE TAPERED ATTACHMENT AND RETAINING NUT, IS POSSIBLE. Remedy: DEALERS WILL INSPECT THE BALL STUD JOINTS AND MEASURE THE TORQUE OF THE NUT FOR ALL FRONT LOWER CONTROL ARMS IN ALL MODELS AFFECTED AS WELL AS THE REAR LOWER CONTROL ARMS ON THE XLR AND CORVETTE. IF THE TORQUE IS NOT AT SPECIFICATION, THE DEALERS WILL REPLACE THE BALL STUD, THE KNUCKLE, AND THE NUT. IF THE TORQUE IS AT SPECIFICATION, THE DEALERS WILL REPLACE THE NUT/WASHER ASSEMBLY ONLY. THE RECALL WILL BEGIN ON AUGUST 25, 2004. OWNERS SHOULD CONTACT CADILLAC AT 1-866-982-2339 OR CHEVROLET AT 1-800-630-2438.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain vehicles, there is a risk that some drivers may bump the ignition key with their knee and unintentionally move the key from out of the "run" position. If this were to occur, engine power, power braking and power steering would be affected, which would unexpectedly increase steering and brake pedal effort, potentially increasing stopping distances and the risk of a crash causing injury and/or damage to property. The timing of the key movement out of the "run" position, relative to the activation of the sensing algorithm of the crash event, may also result in the airbags not deploying in a subsequent collision, increasing the risk of injury. Correction: Dealers are to remove the key blade from the original flip key/transmitter assemblies provided with the vehicle, and provide two new keys and two key rings for every original key. Important note: Until the correction is performed, drivers should adjust their seat and steering column to allow clearance between their knee and the ignition key.
On certain vehicles equipped with an automatic transmission, the transmission shift lever can be moved from the PARK position with the ignition ON and without the operator depressing the brake pedal or in some cases with the ignition turned to OFF. This situation has the potential for the vehicle to roll/move if the shifter is hit accidentally which could result in a crash causing property damages or personal injuries. Correction: Dealers will replace the pawl stopper and a bushing within the shifter assembly.
Certain vehicles do not comply with the requirements of CMVSS 124 - Accelerator Control Systems. The Electronic Throttle Control (ETC) accelerator pedal assembly may not return the engine to idle in three seconds or less at low ambient temperatures if either of the two throttle return springs is broken. Correction: Dealers will replace the ETC pedal assembly.
We checked the EU Safety Gate for recall alerts naming this model and its production years.
Source: EU Safety Gate (European Commission) · CC BY 4.0, © European Union
Production: The vehicles affected were manufactured between 2001 and 2014.. Types: types: GMX320, GMX322, GMT265, "N" Car models: CTS, SRX, DTS (Cadillac), Alero (Chevrolet); type-approval numbers: e13*2001/116*0086*01-*09 (CTS), e13*2001/116*0260*00-*03 and *05-*11 (CTS) , ......
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Crash-test ratings from NHTSA's New Car Assessment Program.
Source: NHTSA (US Department of Transportation) · US public domain
On certain CTS, CTS-V and SRX vehicles, an interaction between the Sensing and Diagnostic Module (SDM) and the vehicle electrical system may cause the driver's frontal airbag and/or roof rail airbag to deploy when the ignition key is turned to the "ON" position. A person positioned for driving may receive minor injuries, such as abrasions, from contact with the airbag. Correction: Dealers will replace the SDM.
Certain vehicles were produced with lower control arm ball stud nut/washer assemblies with washers made of the wrong steel material. The washers may fracture and become loose or fall away from the vehicle, reducing clamp load. Separation of the control arm ball stud and steering knuckle, due to disengagement of the tapered attachment and retaining nut, is possible and may occur without prior indication to the vehicle operator. If the control arm separates from the knuckle, the affected corner of the vehicle will drop and the control arm would be forced downward, contacting the wheel. The affected wheel could tilt outward and create a dragging action that would tend to slow the vehicle and create a tendency for the vehicle to turn in the direction of the affected wheel. In extreme situations, the affected wheel assembly could separate from the vehicle. Separation of the wheel assembly would also sever that wheel's hydraulic brake hose and result in diminished braking performance of the vehicle, which could result in a crash. Correction: Dealers will install a new nut and washer, and if required, replace the ball stud and/or steering knuckle.
On certain vehicles equipped with All-Wheel Drive, the Antilock Brake System (ABS) may temporarily isolate the driver from the foundation brake system for a maximum of 1.25 seconds. This could cause an increase in braking distance, which could result in a crash. Correction: Dealer will reprogram the ABS Electronic Control Unit.
On certain vehicles, one or both front anchor tabs for the front seats may not be engaged in the floor pan reinforcement slots. In a vehicle crash, the seat(s) could pivot rearward, resulting in possible increased injury to its occupant or a rear seat occupant. Correction: Dealer will ensure that both front anchor tabs are fully seated in the floor pan reinforcement slots.