Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2004 Mitsubishi Fuso FM657, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
ON CERTAIN TRUCKS USING AN F060T OR F070T FRONT AXLE, THE FRONT WHEEL HUB OUTER BEARING LOCK NUT MAY HAVE BEEN IMPROPERLY TIGHTENED DURING ASSEMBLY, AND AN INSUFFICIENT AMOUNT OF GREASE MAY HAVE BEEN APPLIED TO THE OUTER BEARING. Remedy: DEALERS WILL INSPECT THE INNER AND OUTER FRONT WHEEL HUB BEARINGS, AND REPLACE ANY BEARING WITH SIGNS OF DAMAGE. THE RECALL BEGAN ON OCTOBER 28, 2004. OWNERS SHOULD CONTACT MITSUBISHI FUSO AT 1-856-467-4500.
ON CERTAIN TRUCKS, THE REBOUND CUSHION MAY STICK TO THE HOOK HINGE BRACKET, DUE TO IMPROPER RUBBER COMPOSITION OF THE CUSHION. THIS CONDITION COULD RESULT IN THE HOOK PIN BRACKET REMAINING IN THE UP (CAB CLOSED) POSITION WHEN THE CAB LATCH IS UNLOCKED. WITH THE HOOK PIN BRACKET IN THE UP POSITION, THE CAB TILT LOCK SWITCH REMAINS CLOSED, IMPROPERLY INDICATING THAT THE CAB LATCH IS LOCKED. Remedy: DEALERS WILL REPLACE THE REBOUND CUSHION WITH A MODIFIED COMPONENT AND ADJUST THE CABLE TILT LOCK SWITCH AND BOTTOM BRACKET AT THE REAR CAB MOUNT. THE RECALL BEGAN ON OCTOBER 28, 2004. OWNERS SHOULD CONTACT MITSUBISHI FUSO AT 1-877-711-0707.
Mitsubishi Fuso Truck of America, Inc. (MFTA) is recalling certain 2004-2017 FE84D, FE85D, FEC52, FEC72, FEC92, FGB72, FK61F and FM657 trucks. These trucks are equipped with Kidde Plastic-Handle or Push Button 'Pindicator' Fire Extinguishers that may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf Remedy: MFTA will notify owners, instructing them to contact Kidde for a replacement fire extinguisher, free of charge. The recall began on January 11, 2018. Owners may contact MFTA customer service at 1-877-711-0707, or Kidde customer service toll-free at 1-855-262-3540, or online at www.kidde.com and click on "Product Safety Recall" for more information. MFTA's number for this recall is MFV00001.
MITSUBISHI FUSO TRUCK OF AMERICA (MFTA) IS RECALLING 156 HALOGEN SEALED BEAM HIGH BEAM HEADLAMP ASSEMBLIES SOLD BETWEEN OCTOBER 24, 2007 AND DECEMBER 2, 2008 FOR USE AS REPLACEMENT EQUIPMENT FOR CERTAIN MITSUBISHI FUSO TRUCKS. THESE LAMPS FAIL TO CONFORM TO THE SAE STANDARDS OR RECOMMENDED PRACTICES REFERENCED IN TABLE I OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." Remedy: MFTA WILL NOTIFY OWNERS AND REPLACE THE HEADLAMPS FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 15, 2009. OWNERS MAY CONTACT MFTA AT 1-856-467-4500.
ON CERTAIN TRUCKS, EQUIPPED WITH A FULL AIR BRAKE SYSTEM, THERE MAY BE 3 POSSIBLE DEFECTS RELATED TO THE PARKING BRAKE CHAMBER PORTION OF THE AIR BRAKE CHAMBER ASSEMBLY. THEY ARE AS FOLLOWS: (1) DUE TO IMPROPER INSTALLATION OF THE PARKING BRAKE CHAMBER END CAP DURING ASSEMBLY, WATER MAY ENTER THE PARKING BRAKE CHAMBER, CAUSING CORROSION OF THE POWER SPRING, LEADING TO POSSIBLE SPRING FAILURE. IN THE WORST CASE, RESULTANT DAMAGE COULD CAUSE THE PARKING BRAKE TO ENGAGE WHILE THE PARKING BRAKE LEVER IS IN THE RELEASED (OFF) POSITION. (2) DUE TO IMPROPER END CAP ATTACHING SCREW DIMENSIONS, WATER MAY ENTER THE PARKING BRAKE CHAMBER, CAUSING CORROSION OF THE POWER SPRING, LEADING TO POSSIBLE SPRING FAILURE. IN THE WORST CASE, RESULTANT DAMAGE COULD CAUSE THE PARKING BRAKE TO ENGAGE WHILE THE PARKING BRAKE LEVER IS IN THE RELEASED (OFF) POSITION. (3) DUE TO IMPROPER TIGHTENING OF THE END CAP ATTACHING SCREW DURING ASSEMBLY, WATER MAY ENTER INTO THE PARKING BRAKE CHAMBER, CAUSING CORROSION OF THE POWER SPRING, LEADING TO POSSIBLE SPRING FAILURE. IN THE WORST CASE, RESULTANT DAMAGE COULD CAUSE THE PARKING BRAKE TO ENGAGE WHILE THE PARKING BRAKE LEVER IS IN THE RELEASED (OFF) POSITION. Remedy: DEALERS WILL FOR ITEM (1) ABOVE, INSPECT THE PARKING BRAKE CHAMBER. THE END CAP WILL BE REPLACED WITH A MODIFIED PART. IF CORROSION IS FOUND INSIDE OF THE CHAMBER, OR ON THE POWER SPRING, THE PARKING BRAKE CHAMBER WILL BE REPLACED. FOR ITEMS 2 AND 3, THE DEALER WILL CHECK THE MANUFACTURER IDENTIFICATION MARK ON PARKING BRAKE CHAMBER. IF MGM IS STAMPED ON THE CHAMBER, IT WILL BE INSPECTED AND THEN ADHESIVE WILL BE APPLIED TO THE END CAP ATTACHING SCREW ON THESE UNITS. IF CORROSION IS FOUND INSIDE OF THE BRAKE CHAMBER OR ON THE POWER SPRING, THE PARKING BRAKE CHAMBER WILL BE REPLACED. THE RECALL BEGAN ON NOVEMBER 9, 2006. OWNERS MAY CONTACT MITSUBISHI FUSO AT 1-856-467-4500.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain vehicles, there may be three possible air brake problems. 1) Due to improper installation of the parking brake chamber end cap, water may enter causing corrosion of the power spring, leading to spring failure. 2) Due to improper end cap attaching screw dimensions, water may enter causing corrosion of the power spring, leading to spring failure. 3) Due to improper tightening of the end cap attaching screw, water may enter causing corrosion of the power spring, leading to spring failure. Any of these problems could cause the parking brake to engage while the parking brake lever is in the released (off) position. Correction: Dealers will inspect and repair or replace as necessary.
On certain vehicles equipped with an F060T or F070T front axle, the front wheel hub outer bearing lock nut may have been improperly tightened during initial assembly, and an insufficient amount of grease may have been applied to the outer bearing. These conditions could result in the outer bearing generating excessive heat and/or breaking, causing the vehicle to become disabled. In the worst case, the excessive heat could cause a fire. Correction: Dealers will inspect the front inner and outer wheel hub bearings, and replace any bearings with signs of damage.
On certain vehicles, the rebound cushion of the cab tilt lock system may stick to the hook hinge bracket. As a result, the hook pin bracket could remain in the up (cab closed) position when the cab latch is unlocked. With the hook pin bracket in the up position, the cab tilt lock switch remains closed, improperly indicating that the cab latch is locked. In the worst case, if the cab latch is unlocked for any reason, the instrument panel cab lock indicator will not notify the driver that the cab tilt lock mechanism is in the unlocked position. Correction: Dealers will replace the rebound cushion and adjust the tilt lock switch and bottom bracket.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain