Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2005 Chevrolet Uplander, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
DORMAN IS RECALLING 979 STEERING KNUCKLES, DORMAN P/NOS. 697-902 AND 697-903, SOLD UNDER DORMAN'S "OE SOLUTIONS<SUP>TM</SUP>" BRAND NAME, AND NAPA P/NOS. 7-8502 AND 7-8503 WHICH WERE SOLD FOR REPLACEMENT USE ON THE VARIOUS VEHICLES LISTED ABOVE. A POTENTIAL MATERIAL OR DESIGN DEFECT COULD RESULT IN THE STEERING KNUCKLE BREAKING IN THE HUB AREA. Remedy: DORMAN WILL NOTIFY OWNERS AND REPLACE THE DEFECTIVE STEERING KNUCKLES FREE OF CHARGE AND REIMBURSE THE REPAIR FACILITY OR OWNER FOR LABOR. THE RECALL BEGAN ON FEBRUARY 23, 2009. OWNERS MAY CONTACT DORMAN'S TOLL-FREE HOTLINE AT 1-800-523-2492 AND PRESS 5.
ON CERTAIN MINIVANS, THE OUTBOARD RELEASE HANDLE ON THE IMPACT-SIDE SECOND-ROW BUCKET SEAT MAY BE ACTUATED AND THE REAR LATCHES MAY UNLATCH EARLY IN A SIDE IMPACT CRASH. THIS WAS DISCOVERED IN A SIDE IMPACT TEST RUN BY GM, UNDER CONDITIONS SIMILAR TO NHTSA'S NEW CAR ASSESSMENT PROGRAM (NCAP) SIDE IMPACT TEST. Remedy: DEALERS WILL REMOVE THE SEAT LATCH RELEASE HANDLE AND INSTALL A BLACK PLASTIC CAP OVER THE EXPOSED METAL STUD TO ELIMINATE THE SIDE IMPACT SAFETY CONCERN FREE OF CHARGE. THE RECALL BEGAN ON APRIL 5, 2005. OWNERS MAY CONTACT SATURN AT 1-800-972-8876, CHEVROLET AT 1-800-630-2438, AND PONTIAC AT 1-800-620-7668.
THE BRAUN CORPORATION HAS NOTIFIED NHTSA ABOUT A DEFECT IN CERTAIN MODEL YEAR 2005-2008 GENERAL MOTORS MOBILITY CONVERSION, HANDICAPPED ACCESSIBLE LOW FLOOR MINIVANS. DURING CONVERSION, THE DRIVER OR PASSENGER SIDE TRAILING ARM MODIFICATION MAY NOT HAVE BEEN ADEQUATELY WELDED. Remedy: DEALERS WILL INSPECT AND WILL HAVE A SUPPLY OF RETROFIT PARTS AVAILABLE TO REMEDY THE VEHICLES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 4, 2010. OWNERS MAY CONTACT BRAUN AT 1-800-488-0359.
CERTAIN SPORT UTILITY VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 135, 'PASSENGER CAR BRAKE SYSTEMS.' TO MEET THE STANDARD, THE VEHICLE MUST NOT MOVE FOR FIVE MINUTES WHEN STOPPED ON A STEEP HILL WITH THE PARKING BRAKE APPLIED AND THE VEHICLE IN NEUTRAL (N). SOME OF THESE VEHICLES FAILED THIS TEST. Remedy: DEALERS WILL INSPECT FOR PARKING BRAKE LEVER SLIPPAGE AT EACH REAR BRAKE CALIPER AND REPLACE THE CALIPER IF LEVER SLIPPAGE IS IDENTIFIED. THE RECALL BEGAN ON NOVEMBER 14, 2005. OWNERS MAY CONTACT BUICK AT 1-866-608-8080, CHEVROLET AT 1-800-630-2438, PONTIAC AT 1-800-620-7668, OR SATURN AT 1-800-972-8876.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Issue: This recall is for aftermarket replacement rear window glass produced by Vitro Automotriz. Certain rear window glass may not have been properly tempered. If the window breaks, the glass may separate into large pieces instead of very small ones. Note: This is a voluntary recall that is not being conducted under the requirements of the Motor Vehicle Safety Act. Safety Risk: Glass that breaks in to large pieces could create a risk of injury. Corrective Actions: The company will notify consumers by mail and instruct them to inspect the designation code marked on the rear window glass. Products affected by this recall have the designation “DOT 287” along with the lettering “VMR” (Replacement Market) and a date code that is before July 2019. This information is printed on the bottom corner of the glass. Consumers should contact Vitro's customer service at 1-412-995-6457 or argbacklites@vitro.com to arrange for replacement of the glass.
On certain Aztek (AWD), Montana (AWD), Relay (AWD), RendezVous (AWD), RendezVous (FWD), Silhouette (AWD), Terraza (AWD), Terraza (FWD), Uplander (AWD) and Venture (AWD) vehicles equipped with independent rear suspension, when operated in extreme cold temperature and on rough roads, water and salt can intrude past the ball joint seal. The combination of theses conditions may then lead to premature wear of the ball joint. If the ball joint wear progresses to the point of separation from the lower control arm, a loss of vehicle control may occur. Correction: Dealers will replace both ball joints with new ball joints which have a revised boot and ball stud to improve the seal to the ball stud shaft.
Certain vehicles do not comply with the requirements of CMVSS 135. To meet the Standard, the vehicle must not move for five minutes when stopped on a steep hill with the parking brake applied and the vehicle in NEUTRAL (N). A part that was not manufactured to specifications can cause the parking brake to fail this test. A loud popping noise as the parking brake is applied or a sudden decrease in the effort required to apply the parking brake can be indications of this condition. When the parking brake is released, the driver may notice unintended braking when accelerating, decelerating, or coasting, and a groan, humming, and/or vibration coming from the rear of the vehicle. Correction: Dealers will inspect for parking brake lever slippage at each rear brake caliper. The calipers will be replaced if lever slippage is identified.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Crash-test ratings from NHTSA's New Car Assessment Program.
Source: NHTSA (US Department of Transportation) · US public domain
On certain vehicles, the outboard release handle on the impact-side second-row bucket seat may be actuated and the rear latches may unlatch early during the crash sequence of a side impact New Car Assessment Program (NCAP) test. If the rear latches of the seat are released early in a severe side impact, the front outboard latch may disengage and increase the potential for injury to the occupant of the seat. Correction: Dealers will replace the seat latch release lever.