Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2006 Freightliner Century ST, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
ON CERTAIN TRUCK-TRACTORS EQUIPPED WITH HOLLAND SIMPLEX SE OR SE II FIFTH WHEELS, THE LATCH LEVER PIVOT BOLT ASSEMBLY MAY HAVE BEEN OVER-TIGHTENED WHICH COULD DISTORT THE PIVOT BOLT SPACER SLEEVE. CORROSION OR CONTAMINATES IN THE PIVOT MAY CAUSE IT TO BIND AND PREVENT THE FIFTH WHEEL JAW FROM LATCHING SECURELY AROUND THE TRAILER KING PIN. Remedy: DEALERS WILL REPLACE THE PIVOT BOLT AND SLEEVE WITH A HEX HEAD SHOULDER BOLT AND WASHER. THE RECALL BEGAN ON JANUARY 3, 2008. OWNERS MAY CONTACT FREIGHTLINER AT 1-800-547-0712.
CERTAIN FREIGHTLINER SCHOOL BUS CHASSIS, HEAVY TRUCKS, AND THOMAS BUILT SCHOOL BUSES MANUFACTURED BETWEEN JULY 2002 AND JULY 3, 2007, EQUIPPED WITH BENDIX SR-7 SPRING BRAKE CONTROL VALVES. THE PARKER SCV BRASS 90 DEGREE SINGLE CHECK VALVES (SCV) WHICH ATTACH TO THE SUPPLY PORT OF A BENDIX SR-7 SPRING BRAKE MODULATING VALVE CAN BREAK APART. PIECES OF THE PARKER SCV CAN BECOME LODGED INSIDE THE SR-7 SPRING BRAKE MODULATING VALVE, POTENTIALLY CAUSING EITHER LEAKAGE OUT OF THE SR-7 VALVE OR PREVENTING AIR FROM PROPERLY EXHAUSTING FROM THE SR-7 VALVE. ALSO, DUE TO A MANUFACTURING DEFECT IN THE INTERNAL RUBBER CHECK VALVE INSIDE THE SR-7 SPRING BRAKE MODULATING VALVES, THE VALVES CAN BECOME DEFORMED AND NOT SEAT PROPERLY. Remedy: FREIGHTLINER WILL NOTIFY OWNERS AND REPAIR THE VEHICLES FREE OF CHARGE. THE RECALL BEGAN ON JANUARY 11, 2008 TO FREIGHTLINER, STERLING, AND FREIGHTLINER CUSTOM CHASSIS OWNERS; TO THOMAS BUILT BUS OWNERS ON FEBRUARY 1, 2008. OWNERS CAN CONTACT FREIGHTLINER AT 1-800-547-0712.
ON CERTAIN TRUCKS EQUIPPED WITH RACK AND PINION STEERING, THE TIE ROD ARMS MAY HAVE BEEN INCORRECTLY INSTALLED. THE THREADED END OF THE BALL SOCKET ASSEMBLY MAY FRACTURE AND SEPARATE. Remedy: DEALERS WILL INSPECT FOR INSTALLATION OF THE STEERING ARMS. STEERING COMPONENTS WILL BE REPLACED ON TRUCKS THAT HAVE INCORRECTLY INSTALLED TIE ROD ARMS. THE RECALL BEGAN ON MAY 1, 2008. OWNER MAY CONTACT FREIGHTLINER AT 1-800-547-0712.
CERTAIN FREIGHTLINER SCHOOL BUSES AND TRUCKS MANUFACTURED FROM OCTOBER 23, 2004, TO MARCH 21, 2006. DURING THE STEERING COLUMN MANUFACTURING PROCESS TWO WELDS MAY HAVE BEEN MISSING. Remedy: FREIGHTLINER WILL NOTIFY OWNERS AND INSPECT AND REPAIR THE AFFECTED VEHICLE FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 30, 2007. OWNERS CAN CONTACT FREIGHTLINER AT 1-800-547-0712.
ON CERTAIN TRUCKS EQUIPPED WITH RACK AND PINION STEERING, THE BALL SOCKET ASSEMBLY AT THE INNER END OF THE DRIVER SIDE TIE ROD MAY BE DAMAGED IN A SHARP TURN. EXCESSIVE TIE ROD ANGLES MAY LOOSEN THE TIE ROD IN THE BALL SOCKET OR DAMAGE THE THREADED TIE ROD SOCKET ATTACHMENT TO THE STEERING RACK ON THE DRIVER SIDE. THE THREADED END OF THE BALL SOCKET ASSEMBLY MAY FRACTURE AND SEPARATE. Remedy: DEALERS WILL CHANGE THE FRONT AXLE STEERING STOPS TO PREVENT INTERFERENCE IN THE TIE ROD BALL SOCKET ASSEMBLY AND STEERING COMPONENTS WILL BE REPLACED FREE OF CHARGE. THE RECALL BEGAN ON JULY 8, 2008, AND WILL BE MAILED IN PHASES THROUGH DECEMBER 31, 2008. OWNERS MAY CONTACT FREIGHTLINER AT 1-800-547-0712.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain trucks, the fifth wheel hitch assembly's lever arm may have been incorrectly installed during the manufacturing process. The lever arm pivot bolt may have been over-tightened which could distort the pivot bolt spacer sleeve and prevent the fifth wheel latch jaw from closing and latching securely around the trailer king pin. This could allow the towed unit to separate from the towing vehicle while underway, potentially causing a crash with injury or death. Correction: Dealers will replace the pivot bolt and sleeve with a hex head shoulder bolt and washer.
On certain trucks, the wiper motor ground wire was omitted during vehicle assembly. As a result, the wiper motor may not operate or may function intermittently. This could lead to reduced visibility and a crash without warning. Correction: Dealers will install a wiper motor ground wire.
On certain trucks, the driver's side inner tie rod may be damaged while the truck is executing a sharp turn. Excessive tie rod angles may loosen the tie rod ball socket and/or damage the threaded tie rod attachment to the steering rack. As a result, the tie rod assembly may fail, possibly causing a loss of vehicle control and a crash. Correction: Dealers will replace the front axle steering stops to limit turning radius and prevent interference with the tie rod assembly.
On certain trucks, the tie rod arms may have been incorrectly installed during vehicle assembly. If the right steering arm is installed on the left knuckle, excessive tie rod angles may loosen the threaded tie rod attachment to the steering rack. As a result, the tie rod assembly may fail, possibly causing a loss of vehicle control and a crash. Correction: Dealers will inspect for proper steering arm installation. Steering components will be replaced on trucks that have incorrectly installed tie rod arms.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
On certain vehicles, the internal rubber check valve inside the Bendix SR-7 spring brake modulating valve can become deformed over time. The effect of this defect is intermittent and presents a potential delay or failure in applying the parking brakes; potentially resulting in a vehicle roll away. Should this occur, the unattended roll away vehicle could strike a bystander or cause property damage. Correction: Dealers will install a check valve repair kit.
On certain vehicles, the steering column may have been manufactured incorrectly. Two welds may have been omitted, which could cause the column to fail, possibly leading to a loss of steering control and a crash without warning. Correction: Dealers will inspect and replace columns with missing welds.
On certain vehicles, the protective cover for the cab Power Distribution Module (PDM) may be missing or improperly installed. If the protective cover is missing or not positioned correctly, any water intrusion from an open window or windshield leak may seep through the upper dash cover seam and drip onto the PDM. Water on the PDM circuits may cause a short circuit resulting in a fire that could cause personal injury. Correction: Dealers will install an updated protective cover.
On certain vehicles, the steering wheel was manufactured with incorrect length Huck fasteners that are too short to allow proper retaining collar engagement. Steering wheel separation will result in a loss of steering control, possibly resulting in a crash. Correction: Dealers will inspect and, if required, repair or replace the steering wheel.
On certain vehicles, the rear spindles may fracture as a result of incorrect heat treat process during vehicle assembly. Rear spindle failure could allow the wheel, tire, and brake drum assembly to separate from the vehicle. The wheel end assembly could become a hazard for other traffic. Correction: Dealers will inspect for the heat treat date code on the end of the rear spindles. Axle housings will be replaced on vehicles manufactured with spindles that have the subject date codes.