Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2006 Freightliner Coronado, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
ON CERTAIN TRUCKS AND MOTOR HOME CHASSIS, THE TOP FLANGE OF THE FRONT AXLE I-BEAM MAY FATIGUE AND FRACTURE. Remedy: DEALERS WILL INSPECT AND REPLACE THE FRONT AXLE ASSEMBLY. THE RECALL BEGAN ON MARCH 15, 2006, FOR PHASE I. PHASE 2 WILL BEGIN DURING AUGUST 2006. THIS RECALL IS BEING CONDUCTED IN TWO PHASES. PHASE I WILL REPLACE THE COMPLETE AXLE ASSEMBLY; AND PHASE II WILL REPLACE THE AXLE BEAM AND STEERING KNUCKLES. OWNERS MAY CONTACT FREIGHTLINER AT 1-800-547-0712.
DAIMLER TRUCKS IS RECALLING 62,000 MY 2005-2007 FREIGHTLINER BUSINESS CLASS, CENTURY CLASS, COLUMBIA, CORONADO, FLD, CLASSIC, STERLING A-LINE, L-LINE, AND WESTERN STAR 4900 TRUCKS. A FRACTURED FUEL LINE COULD LEAK DIESEL FUEL. Remedy: HIGH PRESSURE FUEL LINES AND TRANSFER TUBES WILL BE INSPECTED AND REPLACED FREE OF CHARGED. THE RECALL BEGAN ON JULY 9, 2008. OWNERS MAY CONTACT DAIMLER TRUCKS AT 1-800-547-0712.
ON CERTAIN TRUCK-TRACTORS EQUIPPED WITH HOLLAND SIMPLEX SE OR SE II FIFTH WHEELS, THE LATCH LEVER PIVOT BOLT ASSEMBLY MAY HAVE BEEN OVER-TIGHTENED WHICH COULD DISTORT THE PIVOT BOLT SPACER SLEEVE. CORROSION OR CONTAMINATES IN THE PIVOT MAY CAUSE IT TO BIND AND PREVENT THE FIFTH WHEEL JAW FROM LATCHING SECURELY AROUND THE TRAILER KING PIN. Remedy: DEALERS WILL REPLACE THE PIVOT BOLT AND SLEEVE WITH A HEX HEAD SHOULDER BOLT AND WASHER. THE RECALL BEGAN ON JANUARY 3, 2008. OWNERS MAY CONTACT FREIGHTLINER AT 1-800-547-0712.
CERTAIN FREIGHTLINER SCHOOL BUS CHASSIS, HEAVY TRUCKS, AND THOMAS BUILT SCHOOL BUSES MANUFACTURED BETWEEN JULY 2002 AND JULY 3, 2007, EQUIPPED WITH BENDIX SR-7 SPRING BRAKE CONTROL VALVES. THE PARKER SCV BRASS 90 DEGREE SINGLE CHECK VALVES (SCV) WHICH ATTACH TO THE SUPPLY PORT OF A BENDIX SR-7 SPRING BRAKE MODULATING VALVE CAN BREAK APART. PIECES OF THE PARKER SCV CAN BECOME LODGED INSIDE THE SR-7 SPRING BRAKE MODULATING VALVE, POTENTIALLY CAUSING EITHER LEAKAGE OUT OF THE SR-7 VALVE OR PREVENTING AIR FROM PROPERLY EXHAUSTING FROM THE SR-7 VALVE. ALSO, DUE TO A MANUFACTURING DEFECT IN THE INTERNAL RUBBER CHECK VALVE INSIDE THE SR-7 SPRING BRAKE MODULATING VALVES, THE VALVES CAN BECOME DEFORMED AND NOT SEAT PROPERLY. Remedy: FREIGHTLINER WILL NOTIFY OWNERS AND REPAIR THE VEHICLES FREE OF CHARGE. THE RECALL BEGAN ON JANUARY 11, 2008 TO FREIGHTLINER, STERLING, AND FREIGHTLINER CUSTOM CHASSIS OWNERS; TO THOMAS BUILT BUS OWNERS ON FEBRUARY 1, 2008. OWNERS CAN CONTACT FREIGHTLINER AT 1-800-547-0712.
ON CERTAIN TRUCKS EQUIPPED WITH RACK AND PINION STEERING, THE TIE ROD ARMS MAY HAVE BEEN INCORRECTLY INSTALLED. THE THREADED END OF THE BALL SOCKET ASSEMBLY MAY FRACTURE AND SEPARATE. Remedy: DEALERS WILL INSPECT FOR INSTALLATION OF THE STEERING ARMS. STEERING COMPONENTS WILL BE REPLACED ON TRUCKS THAT HAVE INCORRECTLY INSTALLED TIE ROD ARMS. THE RECALL BEGAN ON MAY 1, 2008. OWNER MAY CONTACT FREIGHTLINER AT 1-800-547-0712.
CERTAIN FREIGHTLINER SCHOOL BUSES AND TRUCKS MANUFACTURED FROM OCTOBER 23, 2004, TO MARCH 21, 2006. DURING THE STEERING COLUMN MANUFACTURING PROCESS TWO WELDS MAY HAVE BEEN MISSING. Remedy: FREIGHTLINER WILL NOTIFY OWNERS AND INSPECT AND REPAIR THE AFFECTED VEHICLE FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 30, 2007. OWNERS CAN CONTACT FREIGHTLINER AT 1-800-547-0712.
ON CERTAIN TRUCKS EQUIPPED WITH RACK AND PINION STEERING, THE BALL SOCKET ASSEMBLY AT THE INNER END OF THE DRIVER SIDE TIE ROD MAY BE DAMAGED IN A SHARP TURN. EXCESSIVE TIE ROD ANGLES MAY LOOSEN THE TIE ROD IN THE BALL SOCKET OR DAMAGE THE THREADED TIE ROD SOCKET ATTACHMENT TO THE STEERING RACK ON THE DRIVER SIDE. THE THREADED END OF THE BALL SOCKET ASSEMBLY MAY FRACTURE AND SEPARATE. Remedy: DEALERS WILL CHANGE THE FRONT AXLE STEERING STOPS TO PREVENT INTERFERENCE IN THE TIE ROD BALL SOCKET ASSEMBLY AND STEERING COMPONENTS WILL BE REPLACED FREE OF CHARGE. THE RECALL BEGAN ON JULY 8, 2008, AND WILL BE MAILED IN PHASES THROUGH DECEMBER 31, 2008. OWNERS MAY CONTACT FREIGHTLINER AT 1-800-547-0712.
Daimler Trucks North America LLC (DTNA) is recalling certain 2002-2017 Freightliner Cascadia, Century Class, Columbia and Coronado trucks and Western Star 4700, 4900, 5700, 5900 and 6900 trucks. These vehicles are equipped with Kidde Plastic-Handle or Push Button 'Pindicator' Fire Extinguishers that may become clogged, preventing the extinguisher from discharging as expected or excessive force may be needed to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf Remedy: DTNA will notify owners, and instruct them to contact Kidde for a replacement fire extinguisher, free of charge. The recall began on April 11, 2018. Owners may contact DTNA customer service at 1-800-547-0712, or contact Kidde customer service toll-free at 1-855-262-3540, or online at www.kidde.com and click on "Product Safety Recall" for more information. DTNA's number for this recall is FL-759.
DAIMLER TRUCKS (DTNA) IS RECALLING CERTAIN MODEL YEAR 2006-2013 FREIGHTLINER, STERLING, AND WESTERN STAR VEHICLES, EQUIPPED WITH DETROIT DIESEL EPA07 AND EPA10, DD13 AND DD15/16 ENGINES, MANUFACTURED FROM JANUARY 20, 2006, THROUGH FEBRUARY 20, 2012. THE PUMP TO RAIL HIGH PRESSURE FUEL LINE SUPPORT SYSTEM USED ON THESE ENGINES IS SENSITIVE TO ASSEMBLY TORQUE AND MAY BE DAMAGED DURING SERVICE WORK. AS A RESULT OF OTHER REPAIRS, THE LINE SUPPORTS MAY LOOSEN, POTENTIALLY LEADING TO FUEL LINE CRACKING AND A FUEL LEAK. Remedy: DTNA WILL NOTIFY OWNERS, AND WHERE NECESSARY, THE HIGH PRESSURE FUEL LINE SUPPORT SYSTEM WILL BE REPLACED BY DTNA AUTHORIZED SERVICE FACILITIES, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 27, 2012. OWNERS MAY CONTACT DTNA AT 1-800-547-0712.
DAIMLER TRUCKS IS RECALLING CERTAIN MODEL YEAR 2006-2012 FREIGHTLINER BUSINESS CLASS M2, CASCADIA, CENTURY, COLUMBIA, CORONADO AND STERLING A-LINE VEHICLES BUILT WITH MERITOR WABCO ELECTRONIC STABILITY CONTROL (ESC) SYSTEM MANUFACTURED FROM SEPTEMBER 15, 2005 THROUGH SEPTEMBER 1, 2011. UNDER CERTAIN ROAD AND DRIVING CONDITIONS, VEHICLE BODY ROLL AND ROAD INCLINATION CHARACTERISTICS MAY ADVERSELY AFFECT THE SLIP ANGLE CALCULATION OF THE ELECTRONIC STABILITY CONTROL (ESC) SYSTEM. THIS MIGHT CAUSE THE ESC TO PERCEIVE AN OVER STEERING SITUATION AND THEREFORE APPLY THE OUTER WHEEL BRAKE ON THE FRONT AXLE UNTIL THE VEHICLE IS PERCEIVED TO BE STABLE. Remedy: DAIMLER TRUCKS WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE ESC MODULE WITH THE APPROPRIATE SOFTWARE VERSION AS NECESSARY, FREE OF CHARGE. AN INTERIM OWNER NOTIFICATION WILL BE MAILED ON OR ABOUT NOVEMBER 21, 2011. THE DATE FOR AVAILABILITY OF THE FINAL REMEDY IS SUBJECT TO VALIDATION TESTING AND PARTS AVAILABILITY. THE SAFETY RECALL BEGAN ON MARCH 28, 2012. OWNERS MAY CONTACT DAIMLER TRUCKS TOLL-FREE AT 1-800-547-0712.
DAIMLER TRUCKS IS RECALLING CERTAIN MODEL YEAR 2005-2011 FREIGHTLINER CASCADIA, COLUMBIA, CENTURY, CORONADO, AND CLASSIC XL TRUCKS MANUFACTURED FROM NOVEMBER 1, 2004, THROUGH JUNE 15, 2010 FOR THE RACK AND PINION STEERING SYSTEM. THE LOWER PINION BEARING MAY CORRODE AND FAIL. A FAILED BEARING MAY LEAD TO DAMAGE OF THE SPOOL VALVE SEALS. A DAMAGE SPOOL VALVE SEAL MAY ALLOW HYDRAULIC FLUID TO FLOW TO THE RIGHT OR LEFT TURN PORT INSTEAD OF FLOWING TO THE RETURN PORT. Remedy: DAIMLER TRUCKS WILL INSPECT THE LOWER BEARING FOR CORROSION. IF CORROSION IS FOUND, THE RACK AND PINION SYSTEM WILL BE REPLACED. IF NO CORROSION IS FOUND, ON THE BEARING, THE BEARING WILL BE PACKED WITH GREASE AND THE RUBBER BELLOWS WILL BE REPLACED WITH SEALANT ADDED BETWEEN THE BELLOWS AND THE RACK HOUSING. AN INTERIM LETTER WAS MAILED IN DECEMBER 2011. OWNERS MAY CONTACT DAIMLER TRUCKS TOLL-FREE AT 1-800-547-0712.
DAIMLER TRUCKS IS RECALLING MODEL YEAR 2004-2010 TRUCKS EQUIPPED WITH CATERPILLAR C15 ENGINE. THE VARIABLE VALVE ACTUATION OIL LINE MAY RUB AGAINST THE P-CLIPS RETAINING THE OIL LINE, CAUSING AN OIL LEAK. Remedy: DAIMLER TRUCKS IS WORKING WITH CATERPILLAR TO REMEDY THESE VEHICLES. PLEASE SEE CATERPILLAR'S DEFECT REPORT 09E-020. CATERPILLAR WILL INSPECT AND REPAIR THE NECESSARY COMPONENTS FREE OF CHARGE. THE RECALL BEGAN ON MAY 5, 2009. OWNERS MAY CONTACT CATERPILLAR TOLL-FREE AT 1-800-447-4986 OR DAIMLER TRUCKS AT 1-800-547-0712.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Issue: On certain trucks equipped with "Fleet Engineer" mud flaps, the bracket for the mud flaps may partially cover the rear reflective tape. Canadian regulations require that reflective tape must be visible on the rear of the truck. Safety Risk: Reflective tape that is covered may make the truck less visible to others and could create an increased risk of a crash. Corrective Actions: Daimler Trucks of North America (DTNA) will notify owners by mail and instruct you to take your truck to an authorized DTNA Service Facility to inspect the reflective tape. It will be moved as necessary to meet the regulations.
On certain trucks equipped with a Detroit Diesel DD13, DD15 or DD16 engine, the support system for the high pressure fuel line (between the fuel pump and the fuel delivery rail) may be damaged during a service repair procedure. Incorrect torque applied to the dampener "P" clip fasteners may damage the fasteners, which could allow the clips to loosen. This could result in a cracked fuel line and a diesel fuel leak. Diesel fuel leakage may ignite on a hot engine surface and cause a fire. As well, diesel fuel spilt on the roadway could endanger other road users by making the roadway unexpectedly slippery. These issues could result in property damage and/or personal injury. Correction: Dealers will replace the high pressure fuel line and install a more robust fuel line support system.
On certain vehicles, specific operating conditions (such as tight, successive, highly banked curves in opposite directions), could trigger unintended Electronic Stability Control (ESC) system intervention. As a result, the ESC may unnecessarily apply one of the front brakes in order to correct the perceived oversteer condition. This may cause the vehicle to deviate from the intended path, thereby increasing the risk of a crash causing property damage and/or personal injury. Correction: Dealers will replace the ESC module.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
On certain vehicles equipped with a Caterpillar C15 engine, the Variable Valve Actuation (VVA) oil line may wear against the P-clip retaining the oil line. An oil leak could result in a vehicle fire causing property damage and/or personal injury. Correction: Caterpillar dealers will replace the VVA oil line with an updated version.
On certain trucks, the high-pressure fuel line at each injector may fatigue and fracture if a fastener at the end of the line is not properly connected. This would allow high pressure atomized diesel fuel to enter the engine compartment, creating a risk of fire, which could result in property damage, personal injury, or death. Correction: Dealers will affect repairs.
On certain trucks, the fifth wheel hitch assembly's lever arm may have been incorrectly installed during the manufacturing process. The lever arm pivot bolt may have been over-tightened which could distort the pivot bolt spacer sleeve and prevent the fifth wheel latch jaw from closing and latching securely around the trailer king pin. This could allow the towed unit to separate from the towing vehicle while underway, potentially causing a crash with injury or death. Correction: Dealers will replace the pivot bolt and sleeve with a hex head shoulder bolt and washer.
On certain trucks, the wiper motor ground wire was omitted during vehicle assembly. As a result, the wiper motor may not operate or may function intermittently. This could lead to reduced visibility and a crash without warning. Correction: Dealers will install a wiper motor ground wire.
On certain trucks, the driver's side inner tie rod may be damaged while the truck is executing a sharp turn. Excessive tie rod angles may loosen the tie rod ball socket and/or damage the threaded tie rod attachment to the steering rack. As a result, the tie rod assembly may fail, possibly causing a loss of vehicle control and a crash. Correction: Dealers will replace the front axle steering stops to limit turning radius and prevent interference with the tie rod assembly.
On certain vehicles, the internal rubber check valve inside the Bendix SR-7 spring brake modulating valve can become deformed over time. The effect of this defect is intermittent and presents a potential delay or failure in applying the parking brakes; potentially resulting in a vehicle roll away. Should this occur, the unattended roll away vehicle could strike a bystander or cause property damage. Correction: Dealers will install a check valve repair kit.
On certain vehicles, the steering column may have been manufactured incorrectly. Two welds may have been omitted, which could cause the column to fail, possibly leading to a loss of steering control and a crash without warning. Correction: Dealers will inspect and replace columns with missing welds.
On certain vehicles, the protective cover for the cab Power Distribution Module (PDM) may be missing or improperly installed. If the protective cover is missing or not positioned correctly, any water intrusion from an open window or windshield leak may seep through the upper dash cover seam and drip onto the PDM. Water on the PDM circuits may cause a short circuit resulting in a fire that could cause personal injury. Correction: Dealers will install an updated protective cover.
On certain vehicles, the steering wheel was manufactured with incorrect length Huck fasteners that are too short to allow proper retaining collar engagement. Steering wheel separation will result in a loss of steering control, possibly resulting in a crash. Correction: Dealers will inspect and, if required, repair or replace the steering wheel.
On certain vehicles, a manufacturing defect of the front axle I-beam top flange may result in a reduction of axle service life. The axle I-beam may fatigue and fracture, causing a possible loss of vehicle control and subsequent crash without prior warning. Correction: Dealers will replace the front axle assembly.
On certain vehicles, the rear spindles may fracture as a result of incorrect heat treat process during vehicle assembly. Rear spindle failure could allow the wheel, tire, and brake drum assembly to separate from the vehicle. The wheel end assembly could become a hazard for other traffic. Correction: Dealers will inspect for the heat treat date code on the end of the rear spindles. Axle housings will be replaced on vehicles manufactured with spindles that have the subject date codes.