Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2006 Sterling Acterra, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
DAIMLER TRUCKS NORTH AMERICA IS RECALLING CERTAIN MODEL YEAR 2005 THROUGH 2012 FREIGHTLINER M2, STERLING ACTERRA, 7500 & 8500, AND THOMAS BUILT HDX VEHICLES MANUFACTURED FROM JUNE 23, 2004, THROUGH MARCH 15, 2011, EQUIPPED WITH SPECIFIC MBE900 EPA04 AND EPA07 MODEL ENGINES. THE INTAKE AIR GRID HEATER MAY SHORT CIRCUIT AND FAIL DUE TO EXCESSIVE INTERNAL TEMPERATURES. Remedy: DAIMLER TRUCKS WILL NOTIFY OWNERS, AND DEALERS WILL REPAIR THE VEHICLES FREE OF CHARGE. REPAIRS WILL BE PERFORMED BY DETROIT DIESEL CORPORATION AUTHORIZED REPAIR FACILITIES. THE SAFETY RECALL BEGAN ON SEPTEMBER 12, 2011. OWNERS MAY CONTACT DAIMLER TRUCKS TOLL-FREE AT 1-800-547-0712. THIS RECALL IS AN EXPANSION OF A PREVIOUS RECALL, CAMPAIGN NUMBER 10V-341.
DAIMLER TRUCKS IS RECALLING 28,764 MY 2001 THROUGH 2008 FCCC B2 AND FS65 SCHOOL BUS CHASSIS, FCCC FB65 CONVENTIONAL BUSES, AND STERLING ACTERRA, FREIGHTLINER FLN, AND BUSINESS CLASS M2 HEAVY TRUCKS, BUILT FROM JANUARY 26, 2000, THROUGH MARCH 24, 2008, MANUFACTURED WITH ARVINMERITOR OR AXLE ALLIANCE COMPANY 6,000 THROUGH 8,000 POUND FRONT AXLES UTILIZING A FOUR PIECE SPINDLE-NUT SET. THESE AXLE ASSEMBLIES MAY HAVE BEEN PRODUCED WITH A THIN SPINDLE NUT WHICH MAY LEAD TO INCORRECT END PLAY, CONE SPIN, EXCESSIVE HEAT, DEGRADATION OF LUBRICATION, WEAR OF THE SPINDLE NUT AND BEARING JOURNAL, OIL CONTAMINATION WITH METAL SHAVINGS, AND PREMATURE BEARING FAILURE. Remedy: DAIMLER TRUCKS WILL NOTIFY OWNERS AND WILL REPAIR THE VEHICLES FREE OF CHARGE. THE RECALL BEGAN ON JANUARY 8, 2009. OWNERS MAY CONTACT DAIMLER TRUCKS AT 1-800-547-0712.
ON CERTAIN TRUCKS EQUIPPED WITH VISTEON WINDSHIELD WIPERS, THE MOTOR MAY HAVE BEEN PRODUCED WITHOUT GREASE APPLIED TO THE OUTPUT SHAFT GEAR. Remedy: DEALERS WILL INSPECT THE WIPER MOTOR FOR THE PRESENCE OF GREASE AND GREASE THE WIPER MOTOR GEARS IF NECESSARY. THE RECALL BEGAN ON FEBRUARY 13, 2006. OWNERS MAY CONTACT FREIGHTLINER AT 1-800-547-0712.
DAIMLER TRUCKS NORTH AMERICA (DTNA) IS RECALLING 24,650 SCHOOL AND NON-SCHOOL BUSES, MOTOR HOME CHASSIS, AND TRUCKS MANUFACTURED FROM MARCH 9, 2004 THROUGH AUGUST 18, 2006, EQUIPPED WITH EPA04 CERTIFIED MBE900 ENGINES, MANUFACTURED BY DETROIT DIESEL BETWEEN MARCH 1, 2004, AND JULY 31, 2006. THE HIGH PRESSURE FUEL LINES AND TRANSFER TUBES MAY FATIGUE AND FRACTURE. Remedy: DETROIT DIESEL WILL NOTIFY OWNERS AND THE VEHICLES WILL BE REPAIRED WITH MORE ROBUST LINES AND VIBRATION DAMPERS FREE OF CHARGE. REPAIRS WILL BE PERFORMED BY AUTHORIZED DETROIT DIESEL DISTRIBUTORSHIPS. THE RECALL BEGAN ON MARCH 9, 2009. OWNERS MAY CONTACT DETROIT DIESEL 1-313-592-3708 OR DTNA TOLL-FREE AT 1-800-547-0712 FOR MORE INFORMATION.
CERTAIN FREIGHTLINER SCHOOL BUS CHASSIS, HEAVY TRUCKS, AND THOMAS BUILT SCHOOL BUSES MANUFACTURED BETWEEN JULY 2002 AND JULY 3, 2007, EQUIPPED WITH BENDIX SR-7 SPRING BRAKE CONTROL VALVES. THE PARKER SCV BRASS 90 DEGREE SINGLE CHECK VALVES (SCV) WHICH ATTACH TO THE SUPPLY PORT OF A BENDIX SR-7 SPRING BRAKE MODULATING VALVE CAN BREAK APART. PIECES OF THE PARKER SCV CAN BECOME LODGED INSIDE THE SR-7 SPRING BRAKE MODULATING VALVE, POTENTIALLY CAUSING EITHER LEAKAGE OUT OF THE SR-7 VALVE OR PREVENTING AIR FROM PROPERLY EXHAUSTING FROM THE SR-7 VALVE. ALSO, DUE TO A MANUFACTURING DEFECT IN THE INTERNAL RUBBER CHECK VALVE INSIDE THE SR-7 SPRING BRAKE MODULATING VALVES, THE VALVES CAN BECOME DEFORMED AND NOT SEAT PROPERLY. Remedy: FREIGHTLINER WILL NOTIFY OWNERS AND REPAIR THE VEHICLES FREE OF CHARGE. THE RECALL BEGAN ON JANUARY 11, 2008 TO FREIGHTLINER, STERLING, AND FREIGHTLINER CUSTOM CHASSIS OWNERS; TO THOMAS BUILT BUS OWNERS ON FEBRUARY 1, 2008. OWNERS CAN CONTACT FREIGHTLINER AT 1-800-547-0712.
ON CERTAIN TRUCK-TRACTORS EQUIPPED WITH HOLLAND SIMPLEX SE OR SE II FIFTH WHEELS, THE LATCH LEVER PIVOT BOLT ASSEMBLY MAY HAVE BEEN OVER-TIGHTENED WHICH COULD DISTORT THE PIVOT BOLT SPACER SLEEVE. CORROSION OR CONTAMINATES IN THE PIVOT MAY CAUSE IT TO BIND AND PREVENT THE FIFTH WHEEL JAW FROM LATCHING SECURELY AROUND THE TRAILER KING PIN. Remedy: DEALERS WILL REPLACE THE PIVOT BOLT AND SLEEVE WITH A HEX HEAD SHOULDER BOLT AND WASHER. THE RECALL BEGAN ON JANUARY 3, 2008. OWNERS MAY CONTACT FREIGHTLINER AT 1-800-547-0712.
Daimler Trucks North America LLC (DTNA) is recalling certain 2004-2019 Freightliner 108SD, 114SD, 122SD, Cascadia, Columbia, Classic, FL80, FLD 120SD, Business Class M2, Western Star 4700, 4900, 6900, Sterling Acterra, L7500, LT7500, L8500, LT8500, L9500, and LT9500 vehicles. The vehicles may have an insufficient service brake air reservoir capacity. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems." Remedy: DTNA will notify owners, and dealers will add air reservoir capacity to the affected vehicles. Owner letters were mailed on November 29, 2021. Owners may contact DTNA customer service at 1-800-547-0712. DTNA's number for this recall is FL-815.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Issue: Certain trucks were built with air reservoir tanks that are too small in relation to the size of the air brake chambers. Canadian regulations require enough air reservoir capacity to ensure the brakes work even with heavy use or when there is a partial loss of the air system. Safety Risk: Reduced braking could cause extended stopping distances and increase the risk of a crash. Corrective Actions: The company will notify owners by mail and instruct them to take their truck to a Daimler Trucks North America authorized service facility to modify the truck to ensure it meets Canadian regulations.
On certain vehicles equipped with an MBE900 (EPA04 and EPA07) engine, the intake air grid heater may short circuit and fail. This could result in a vehicle fire causing property damage and/or personal injury. Correction: Dealers will install an additional external relay to prevent battery connection to the grid heater when the vehicle is not running and when grid heater control signal is absent.
On certain vehicles, high pressure fuel lines and transfer tubes may fatigue and fracture, causing a diesel fuel leak. Fuel leakage, in the presence of an ignition source, could result in a fire. Correction: Dealers will replace the fuel lines and transfer tubes with more robust versions.
On certain vehicles, incorrect spindle nuts may have been installed during vehicle assembly. This could cause incorrect end play, cone spin, excessive heat, degradation of lubrication, wear of the spindle nut and bearing journal, oil contamination with metal shavings, and premature bearing failure. Continued operation could lead to wheel separation, which could result in a vehicle crash. As well, this situation creates the risk that nearby bystanders or motorists be struck by a wayward wheel assembly. Either of these concerns could cause property damage, personal injury, or death. Correction: Dealers will affect repairs.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
On certain trucks, the fifth wheel hitch assembly's lever arm may have been incorrectly installed during the manufacturing process. The lever arm pivot bolt may have been over-tightened which could distort the pivot bolt spacer sleeve and prevent the fifth wheel latch jaw from closing and latching securely around the trailer king pin. This could allow the towed unit to separate from the towing vehicle while underway, potentially causing a crash with injury or death. Correction: Dealers will replace the pivot bolt and sleeve with a hex head shoulder bolt and washer.
On certain vehicles, the internal rubber check valve inside the Bendix SR-7 spring brake modulating valve can become deformed over time. The effect of this defect is intermittent and presents a potential delay or failure in applying the parking brakes; potentially resulting in a vehicle roll away. Should this occur, the unattended roll away vehicle could strike a bystander or cause property damage. Correction: Dealers will install a check valve repair kit.
On certain vehicles, the windshield wiper motor may have been produced without grease applied to the output shaft gear. After a period of continuous use on the high-speed setting, lack of grease may cause the gear teeth to distort and/or fracture during operation, resulting in the loss of wiper function. Depending on the occurrence and weather situation, driver visibility could be reduced, which could result in a crash. Correction: Dealers will replace the wiper motor assembly.
On certain vehicles, a manufacturing defect of the front axle I-beam top flange may result in a reduction of axle service life. The axle I-beam may fatigue and fracture, causing a possible loss of vehicle control and subsequent crash without prior warning. Correction: Dealers will replace the front axle assembly.
On certain vehicles, the rear spindles may fracture as a result of incorrect heat treat process during vehicle assembly. Rear spindle failure could allow the wheel, tire, and brake drum assembly to separate from the vehicle. The wheel end assembly could become a hazard for other traffic. Correction: Dealers will inspect for the heat treat date code on the end of the rear spindles. Axle housings will be replaced on vehicles manufactured with spindles that have the subject date codes.