Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2007 Damon Outlaw, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
THOR MOTOR COACH IS RECALLING CERTAIN MODEL YEAR 2007-2010 DAMON CHALLENGER, MODEL YEAR 2008-2009 CHALLENGER PLATINUM, MODEL YEAR 2007-2011 DAYBREAK, MODEL YEAR 2010 DAYBREAK CLASSIC, MODEL YEAR 2009-2010 DAYBREAK SPORT, MODEL YEAR 2007-2009, OUTLAW AND MODEL YEAR 2011 FOUR WINDS HURRICANE, RECREATIONAL VEHICLES MANUFACTURED FROM MARCH 2007, THROUGH AUGUST 2008. THE FUEL-FILL CAP ASSEMBLIES USED TO SEAL THE UNUSED SIDE OF THE DUAL-FILL GASOLINE FUEL TANK WERE PRODUCED WITH A HOSE MATERIAL THAT DID NOT MEET DESIGN SPECIFICATIONS. DURING NORMAL USAGE THE HOSE MATERIAL MAY DETERIORATE WHICH MAY RESULT IN FUEL LEAKS. Remedy: NAVISTAR/WORKHORSE IS HANDLING THE REMEDY AND OWNER NOTIFICATION FOR THIS CAMPAIGN PLEASE SEE NAVISTAR/WORKHORSE'S DEFECT REPORT 10V-348. NAVISTAR/WORKHORSE WILL REPLACE THE ORIGINAL FUEL-FILL CAP ASSEMBLIES WITH ONES ASSEMBLED WITH HOSE MATERIAL THAT MEETS DESIGN SPECIFICATIONS. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. OWNERS MAY CONTACT NAVISTAR AT 1-260-461-1890.
CERTAIN MOTOR HOMES BUILT ON WORKHORSE CHASSIS MAY HAVE BEEN EQUIPPED WITH INCORRECT STEERING INTERMEDIATE SHAFTS. THE SPLINE CAN STRIP WHILE THE STEERING WHEEL IS BEING TURNED. Remedy: WORKHORSE IS CONDUCTING THIS RECALL (PLEASE SEE 06V148000) AND WILL INSPECT AND, IF NECESSARY, REPLACE THE STEERING INTERMEDIATE SHAFT. OWNERS MAY CONTACT WORKHORSE AT 1-877-294-6773 OR DAMON AT 574-264-2900.
DAMON IS RECALLING 265 MY 2007 INTRUDER (373, 374, 378), MY 2007-2009 OUTLAW (3611), AND MY 2009 CHALLENGER (371, 376, 377, 378) MOTOR HOMES BUILT ON FORD CHASSIS FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 120, 'TIRE SELECTION AND RIMS FOR MOTOR VEHICLES OTHER THAN PASSENGER CARS." THE METRIC AND ENGLISH VALUES FOR THE TIRE AIR PRESSURES WERE INADVERTENTLY SWITCHED. THE LABELS READ 90KPA/620PSI AND SHOULD READ 620KPA/90PSI. Remedy: OWNERS WILL BE SENT A REVISED CERTIFICATION LABEL WITH THE CORRECT TIRE PRESSURE VALUES ALONG WITH INSTALLATION INSTRUCTIONS. THE RECALL BEGAN ON JULY 14, 2008. OWNERS MAY CONTACT DAMON AT 1-800-860-3812.
ON CERTAIN MOTOR HOMES BUILT ON WORKHORSE CHASSIS AND EQUIPPED WITH GM 8.1L V8 ENGINES, IMPROPER HARDENING DURING THE HEAT TREATMENT PROCESS CAN CAUSE THE FUEL RAIL PULSE DAMPER RETAINER CLIP TO FRACTURE, RESULTING IN INADEQUATE RETENTION OF THE DAMPER. IF THE DAMPER BECOMES LOOSE, FUEL COULD BE PUMPED BY THE FUEL PUMP INTO THE UNDER HOOD AREA. Remedy: CHEVROLET AND WORKHORSE ARE HANDLING THE OWNER NOTIFICATION AND REMEDY FOR THIS CAMPAIGN (PLEASE SEE 06V225 AND 06V289). DEALERS WILL REPLACE THE FUEL RAIL PULSE DAMPER RETAINER CLIPS ON THESE ENGINES FREE OF CHARGE. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438, WORKHORSE AT 877-294-6773, OR DAMON AT 1-574-264-5517.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain vehicles equipped with an optional dual-fill 75 or 100 gallon fuel tank, the fuel cap assembly used to seal the unused side of the dual-fill fuel tank may have been manufactured with a hose material that does not meet design specifications. During normal usage the hose may deteriorate and cause a fuel leak. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will replace the original fuel fill cap assembly with an updated version.
On certain motorhomes equipped with Workhorse Custom Chassis, the engine fuel rail pulse damper retainer clip may fracture, resulting in inadequate retention of the damper. If the damper comes loose, a fuel leak may result in the underhood area which may result in a fire. Correction: Dealers will replace the engine fuel rail pulse damper retainer clip.
On certain vehicles equipped with Workhorse Custom Chassis, an incorrect steering intermediate shaft may have been installed. The incorrect part has a finer pitch spline. Use of the incorrect part may cause the spline not to match correctly with the steering gear input shaft. This could cause the spline to strip if the steering wheel is turned with a significant amount of force. This failure is likely only to occur when the vehicle is stopped or during tight turning manoeuvres at very low speeds. This condition may result in a loss of steering control. Correction: Dealers will replace the shaft.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain