Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2007 Kenworth T600, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
PACCAR IS RECALLING CERTAIN MODEL YEAR 2007-2011 KENWORTH C500, T2000, T600, AND T660, AS WELL AS MODEL YEAR 2009-2011 PETERBILT 387 AND 388 TRUCKS EQUIPPED WITH CATERPILLAR C15 ENGINE AND MANUFACTURED FROM MAY 11, 2006, THROUGH SEPTEMBER 17, 2010. DEGRADATION OF A COMBUSTION TUBE WELD CAN CAUSE RADIAL HEAT IMPINGEMENT ON THE BODY WHICH MAY BURN THROUGH CERTAIN BODIES USED ON C15 ENGINES. Remedy: CATERPILLAR IS HANDLING THE OWNER NOTIFICATION AND REMEDY FOR THIS CAMPAIGN. PLEASE SEE CATERPILLAR'S DEFECT REPORT 11E-006. CATERPILLAR WILL REPLACE THE SINGLE PIECE COMBUSTION TUBE WITH A THICK WALL COMBUSTION TUBE WHICH WILL NOT ALLOW THE HEAT TO BREAK THROUGH. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. DUE TO A PARTS SUPPLY ISSUE, OWNERS WILL BE NOTIFIED BY THE END OF APRIL 2011 ABOUT THE SAFETY DEFECT, AND WILL THEN BE NOTIFIED AGAIN ONCE THE FREE REMEDY IS AVAILABLE, CURRENTLY ESTIMATED TO BE AROUND LATE JULY 2011. OWNERS MAY CONTACT CATERPILLAR TOLL-FREE AT 1-800-447-4986.
PACCAR IS RECALLING 4,883 MY 2006-2009 KENWORTH T600, T660, T800, W900, T2000 AND MY 2008-2009 PETERBILT 365, 367, 379, 384, 386, 387, 388 AND 389 TRUCKS. INADEQUATE STIFFNESS OF THE DIESEL PARTICULATE FILTER (DPF) BRACKET COULD RESULT IN SEPARATION OF THE DPF FROM THE CHASSIS. Remedy: PACCAR IS WORKING WITH CATERPILLAR TO REPAIR THESE VEHICLES (PLEASE SEE 08E041). OWNERS MAY CONTACT CATERPILLAR AT 1-800-447-4986 OR KENWORTH AT 1-425-828-5440 OR PETERBILT AT 1-940-591-4196.
PACCAR IS RECALLING 172 MY 2007 KENWORTH T800 SHORT HOOD, W900 LONG HOOD AND T600 TRACTOR/TRAILERS EQUIPPED WITH SAF-HOLLAND SIMPLEX FIFTH WHEELS. IF THE PIVOT BOLT JOINT FOR THE LEVER BAR IS OVER TORQUED, THE SPACER DEFORMS, AND MAKES CONTACT WITH THE LEVER BAR. THIS CONDITION COUPLED WITH CORROSION ASSOCIATED WITH THE SEASONAL DRY OUT, CAN AFFECT THE LOCK SYSTEM OF THE FIFTH WHEEL, PREVENTING THE FIFTH WHEEL JAW FROM LATCHING SECURELY AROUND THE TRAILER KING PIN. Remedy: KENWORTH IS WORKING WITH SAF-HOLLAND SIMPLEX AND WILL INSPECT THE PIVOT BOLT JOINT FOR A DEFORMED SPACER AND REPLACE THE BOLT, WASHER AND SPACER WITH A HEX-HEAD SHOULDER BOLT AND WASHER FREE OF CHARGE. THE RECALL BEGAN ON MAY 1, 2008. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440 OR SAF-HOLLAND AT 1-231-773-3271.
PACCAR IS RECALLING CERTAIN MODEL YEAR 2007-2008 KENWORTH AND PETERBILT VEHICLES MANUFACTURED FROM FEBRUARY 2, 2006 THROUGH APRIL 30, 2007. THE BEARING SURFACES OF THE EXTENDED LUBE UNIVERSAL JOINT THAT ATTACHES THE INTER-AXLE DRIVELINE TO THE DRIVE AXLE MAY BECOME PREMATURELY WORN DUE TO BREAKDOWN OF LUBRICATION AND/OR EXCESSIVE HEAT. PREMATURELY WORN BEARING SURFACES MAY RESULT IN THE U-JOINT BECOMING LOOSE AND/OR BINDING. THIS CONDITION MAY RESULT IN UNIVERSAL JOINT FAILURE, ALLOWING THE INTER-AXLE DRIVELINE TO DETACH FROM THE AXLE. Remedy: PACCAR IS WORKING WITH ITS SUPPLIER TO REMEDY THE VEHICLES FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING FEBRUARY 2011. OWNERS MAY CONTACT KENWORTH AT 425-828-5440 AND PETERBILT AT 940-591-4196.
PACCAR IS RECALLING 3,573 MY 2007 KENWORTH C500, T800, T600, T2000, AND W900 CHASSIS BUILT WITH PHILLIPS QCS II TRAILER CABLE CONNECTION AND TRAILER CABLE MOUNTING BRACKET WITH 'U-SHAPED' CUT OUT. CERTAIN TRAILER CABLE MOUNTING BRACKETS HAVE A 'U-SHAPED' CUT OUT THAT ONLY PARTIALLY SUPPORTS THE TRAILER CABLE CONNECTION. PARTIAL SUPPORT OF THE CABLE CONNECTION MAY ALLOW THE MOLDED BOOT AND ELECTRICAL GROUND PIN TO PARTIALLY OR COMPLETELY PULL AWAY FROM THE 7-WAY SOCKET. PARTIAL OR COMPLETE DETACHMENT OF THE CABLE CONNECTION CAN CAUSE REDUCED WATER RESISTANCE AND POTENTIAL LOSS OF ELECTRICAL GROUND. THERE IS ALSO A POSSIBILITY THE TRAILER LIGHTS MAY FAIL TO ILLUMINATE WITHOUT THE OPERATOR'S KNOWLEDGE. Remedy: DEALERS WILL INSTALL A REINFORCEMENT BRACKET BETWEEN THE FLEXIBLE BACK OF THE QCS II MOLDED BOOT AND THE FRAME BRACKET, AND REATTACH THE SUPPORTING BOLTS. THE RECALL BEGAN ON MAY MAY 30, 2008. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440.
KENWORTH IS RECALLING 3,423 MY 2004-2009 T2000, T800,T600, W900 AND T660 VEHICLES. INCREASED BRAKE EXCITATION IN A CERTAIN VEHICLE CONFIGURATION WHICH INCLUDES BENDIX DRUM BRAKES, WIDE BASE LOW PROFILE SINGLE TIRES, AND AN AG400 OR AG460 REAR SUSPENSION, DUE TO ITS UNIQUE BRAKE CLOCKING AND CAM TUBE LENGTH, CAN CAUSE FATIGUE AND CRACKING TO BRAKE ASSEMBLY COMPONENTS. Remedy: DEALERS WILL INSPECT THE REAR AXLE BRAKES ASSEMBLY, REPLACE CRACKED REAR AXLE BRAKES ASSEMBLY COMPONENTS WHERE REQUIRED, AND INSTALL CAM TUBE SUPPORT BRACKETS ON ALL REAR AXLE WHEEL ENDS FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN OR BEFORE JULY 25, 2009. OWNER MAY CONTACT KENWORTH AT 1-425-828-5440.
PACCAR IS RECALLING 130 MY 2004-2009 T2000, T800, T600, W900 AND T660 KENWORTH TRUCKS BUILT WITH AN AG400 REAR SUSPENSION, LONG STROKE BRAKE CHAMBERS, AND WIDE BASE TIRES (SUPER SINGLES). THESE VEHICLES MAY DEVELOP AN INCREASE IN LATERAL AND VERTICAL AXLE MOVEMENT. THIS MOVEMENT MAY CAUSE PART OR PARTS OF THE BRAKE ASSEMBLY (BRAKE CAM TUBE SUPPORT, BRAKE CHAMBER BRACKET, BRAKE CHAMBER, BRAKE SPIDER) TO DEVELOP FATIGUE CRACKS, POSSIBLY RESULTING IN THE FAILURE OF THE PART OR PARTS WITHIN THE BRAKE ASSEMBLY. Remedy: DEALERS WILL INSTALL THE CAM TUBE SUPPORT BRACKETS ON ALL OF THE REAR AXLE WHEEL ENDS. INSPECT THE REAR AXLE BRAKE ASSEMBLY AND REPLACE IT IF CRACKED. THE RECALL IS EXPECTED TO BEGIN DURING NOVEMBER 2008. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440.
PACCAR IS RECALLING 292 AFTERMARKET SAF HOLLAND FIFTH WHEELS SOLD FOR USE ON MY 2007 KENWORTH T800 SHORT HOOD, W900 LONG HOOD AND T600 TRACTOR/TRAILERS. IF THE PIVOT BOLT JOINT FOR THE LEVER BAR IS OVER TORQUED, THE SPACER DEFORMS, AND MAKES CONTACT WITH THE LEVER BAR. THIS CONDITION COUPLED WITH CORROSION ASSOCIATED WITH THE SEASONAL DRY OUT, CAN AFFECT THE LOCK SYSTEM OF THE FIFTH WHEEL, PREVENTING THE FIFTH WHEEL JAW FROM LATCHING SECURELY AROUND THE TRAILER KING PIN. Remedy: PACCAR IS WORKING WITH SAF-HOLLAND AND WILL INSPECT THE PIVOT BOLT JOINT FOR A DEFORMED SPACER AND REPLACE THE BOLT, WASHER AND SPACER WITH A HEX-HEAD SHOULDER BOLT AND WASHER FREE OF CHARGE. THE MANUFACTURER HAS NOT YET PROVIDED AN OWNER NOTIFICATION SCHECDULE. OWNERS MAY CONTACT PACCAR AT 1-415-828-5000 OR SAF-HOLLAND AT 1-231-773-3271.
ON CERTAIN TRUCKS, THE AXLE HOUSINGS MAY HAVE BEEN MANUFACTURED WITH STEEL THAT WAS OUT OF SPECIFICATION WHICH COULD RESULT IN A FATIGUE FAILURE OVER TIME. Remedy: DEALERS WILL INSPECT AND REPLACE THE AXLES FREE OF CHARGE. THE RECALL BEGAN ON MAY 9, 2007. OWNERS MAY CONTACT KENWORTH AT 425-828-5440 AND PETERBILT AT 1-940-591-4196.
ON CERTAIN TRUCKS, IF THE IGNITION SWITCH IS TURNED ON PRIOR TO INITIAL START UP IN THE MANUFACTURING PLANT OR DURING THE FILTER REPLACEMENT IN THE FIELD, A SMALL FLAME WILL IGNITE WHEN THE FUEL IS ADDED TO PRIME THE SYSTEM. Remedy: DEALERS WILL INSPECT THE FILTER FOR THE DATE CODES OF THE SUSPECT FILTERS AND REPLACE THOSE HEATING ELEMENTS FREE OF CHARGE. THE RECALL BEGAN ON MARCH 21, 2007. OWNERS MAY CONTACT KENWORTH AT 425-828-5440 AND PETERBILT AT 940-591-4201.
ON CERTAIN TRUCKS EQUIPPED WITH CATERPILLAR C11, C13 OR C15 ENGINES, THE OIL FILL CAP CAN BECOME DISLODGED DUE TO CAP DAMAGE OR IMPROPER INSTALLATION AND BECOME LODGED IN THE U-JOINT OF THE STEERING DRIVELINE AND STEERING GEAR. Remedy: PACCAR IS WORKING WITH CATERPILLAR TO REPAIR THESE VEHICLES. REVISED OIL CAP RETENTION BASED ON THE ENGINE MODEL/CONFIGURATION WILL BE INCORPORATED TO PREVENT STEERING LOCK-UP. THE RECALL BEGAN DURING DECEMBER 2007. OWNERS MAY CONTACT CATERPILLAR AT 1-800-447-4986 OR KENWORTH AT 425-828-5440.
CERTAIN TRUCKS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS." THE TRAILER LIGHT LINE MAY HAVE BEEN ROUTED USING TOO TIGHT OF A BEND RADIUS. THIS ROUTING METHOD COULD CAUSE THE WIRES WITHIN THE HARNESS PLUG TO BE PULLED AWAY FROM THE CHASSIS PLUG RESULTING IN AN INTERMITTENT OR COMPLETE ELECTRICAL POWER LOSS TO THE TRAILER. Remedy: DEALERS WILL REROUTE THE LIGHT LINE TO ELIMINATE THE EXCESSIVE BEND RADIUS AND REPLACE ANY PLUG OR HARNESS THAT HAS BEEN DAMAGED FREE OF CHARGE. THE RECALL BEGAN ON APRIL 16, 2007. OWNER MAY CONTACT KENWORTH AT 425-828-5440.
ON CERTAIN TRUCKS EQUIPPED WITH A TRW TILT/TELESCOPING STEERING COLUMN, THE TILT LOCKING MECHANISM ON THE STEERING COLUMN MAY DISENGAGE. THIS COULD PREVENT THE STEERING COLUMN FROM LOCKING IN TO PREDETERMINED POSITIONS. Remedy: DEALERS WILL REPLACE THE TILT LOCKING MECHANISM WITH A REVISED DESIGN THAT INCORPORATES A NEW BRACKET FOR RESTRAINING THE TILTING MECHANISM. THE RECALL BEGAN ON DECEMBER 22, 2006. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440.
ON CERTAIN TRUCKS, THE REMOVABLE TOW HITCH ,WHEN USED TO TOW OR LIFT A VEHICLE, CAN FAIL DUE TO DEFECTIVE MATERIAL IN THE TOW HITCH. Remedy: DEALERS WILL REPLACE THE TOW PIN ASSEMBLY FREE OF CHARGE. THE RECALL BEGAN ON SEPTEMBER 4, 2007. OWNERS MAY CONTACT KENWORTH AT 425-828-5440 OR PETERBILT AT 940-591-4201.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain trucks equipped with a Caterpillar C15 diesel engine, the Diesel Particulate Filter (DPF) combustion tube may fail. This could result in a vehicle fire causing property damage and/or personal injury. Correction: Dealers will replace the DPF combustion tube.
On certain vehicles, the bearing surfaces of the extended lube universal joint that attaches the inter-axle driveline to the drive axle may become prematurely worn due to breakdown of the lubrification and/or excessive heat. Prematurely worn bearing surfaces may result in the u-joint becoming loose and/or binding. If undetected, the condition may result in universal joint failure, allowing the inter-axle driveline to detach from the axle, which may cause the vehicle to become disabled in the roadway. Lost propulsion, in conjunction with traffic, road conditions, and the driver's reactions, could increase the risk of a crash. In addition a driveline component separating from the vehicle could strike another vehicle, stationary object, or bystander, causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the interaxle driveline universal joint.
Certain vehicles may suffer cracking of various brake assembly components (i.e. brake cam tube mounting flanges, brake air chamber bracket, brake air chamber, brake spider). Over time, this cracking can cause a complete fracture of the cam tube, which could increase stopping distances and decrease parking brake hold capability. A reduction of braking capability could increase the risk of a crash causing property damage, personal injury or death. Correction: Dealers will inspect the rear axle brake assembly, replace cracked rear axle brake components where required, and install cam tube support brackets on all rear axle wheel ends.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
On certain vehicles equipped with a Caterpillar C15 engine, the Variable Valve Actuation (VVA) oil line may wear against the P-clip retaining the oil line. An oil leak could result in a vehicle fire causing property damage and/or personal injury. Correction: Caterpillar dealers will replace the VVA oil line with an updated version.
Certain vehicle configuration which includes an AG400 rear suspension, long stroke brake chambers, and wide base tires may develop an increase in lateral and vertical axle movement. This movement may cause part or parts of the brake assembly to develop fatigue cracks, possibly resulting in the failure of part or parts within the brake assembly. A failure may reduce vehicle brake performance, increasing the risk of a crash causing personal injury or death. Correction: Dealers will affect repairs.
On certain trucks, the inadequate stiffness of the Diesel Particulate Filter (DPF) bracket could result in the separation of the DPF from the chassis, which could result in personal injuries or death to motorists or bystanders. Correction: Caterpillar dealers will replace bracket as necessary.
On certain vehicles, the trailer cable mounting bracket has a "U-shaped" cut-out that only partially supports the trailer cable connection. This may allow the moulded boot and electrical ground pin to partially or completely pull away from the 7-way socket. Partial or complete detachment can cause reduced water resistance and potential loss of electrical ground. There is also a possibility the trailer lights may fail to illuminate without the operator's knowledge. Reduced visibility during hours of darkness could result in a vehicle crash, causing personal injury or death. Correction: Dealers will install a reinforcement bracket.
On certain trucks, the removable front tow hitch assembly may fail. This could result in personal injury or property damage if the assembly failed during the un-decking or towing of a vehicle. Correction: Dealers will replace the tow pin assembly with a revised version.
On certain trucks equipped with Caterpillar C11, C13 and C15 engines, the oil fill cap can become dislodged due to cap damage or improper installation. The cap can become lodged in the u-joint of the steering driveline and steering gear, causing difficulty steering the vehicle and/or complete steering lock-up. A loss of steering control can result in a vehicle crash causing injury or death. Correction: Dealers will install an oil cap retention chain to C11 engines and will modify the existing retention chain anchor point on C13 and C15 engine. Damaged oil fill caps will be replaced.
On certain trucks, when the ignition key is in the 'ON' position, the pre-heater, located in the fuel filter base, is energized. If this pre-heater is energized while maintenance is being performed on the fuel filter, diesel fuel could ignite within the filter housing. A fire within the fuel filter housing may spread possibly resulting in property damage or personal injury. Correction: Dealers will inspect and, if required, replace the fuel heater assembly.
On certain trucks, the axle housing may have been manufactured with steel that was out of specification (9.5mm thick instead of 11mm thick), which could result in a fatigue failure over time. If failure occurs, the axle may lock-up or the end of the axle could come off, which may result in a vehicle crash with injury or death. Correction: Dealers will inspect and, if required, replace the axles.
On certain trucks, the trailer light wiring harness may have been routed incorrectly during vehicle assembly. This could cause the wires within the harness plug to be pulled away from the chassis plug, resulting in an intermittent or complete electrical power loss to the trailer. This would cause a loss of all trailer lighting and ABS function. Inoperative side markers and tail lamps would make the trailer less visible to other drivers during times of reduced visibility. A loss of brake lamp function would not allow a following driver to know when the brakes have been applied, and a rear-end crash could occur as a result. Correction: Dealers will re-route the wiring harness.
On certain trucks, the tilt locking mechanism on the steering column may disengage, preventing the steering column from locking into predetermined positions. Should the locking mechanism disengage, the tilting travel of the column would be unrestricted. This could allow the steering wheel to impact the dash and limit the movement of the steering wheel. Correction: Dealers will install a bracket designed to restrain the tilting mechanism and prevent it from disengaging.