Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2007 Kenworth T800, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
PACCAR is recalling certain model year 2007-2014 Kenworth T800 and W900 trucks manufactured March 22, 2006, through July 15, 2013 and equipped with Primaax tridem rear suspensions and a pusher and/or tag axle. The affected trucks have brake chambers that take longer to apply or release the brakes than the required time limit. Thus, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 121, "Air Brake Systems." Remedy: PACCAR will notify owners, and dealers will modify the air brake system, free of charge. The recall began on January 15, 2014. Owners may contact PACCAR at 1-425-468-7400. Kenworth's recall number is 13KWL.
PACCAR IS RECALLING 4,883 MY 2006-2009 KENWORTH T600, T660, T800, W900, T2000 AND MY 2008-2009 PETERBILT 365, 367, 379, 384, 386, 387, 388 AND 389 TRUCKS. INADEQUATE STIFFNESS OF THE DIESEL PARTICULATE FILTER (DPF) BRACKET COULD RESULT IN SEPARATION OF THE DPF FROM THE CHASSIS. Remedy: PACCAR IS WORKING WITH CATERPILLAR TO REPAIR THESE VEHICLES (PLEASE SEE 08E041). OWNERS MAY CONTACT CATERPILLAR AT 1-800-447-4986 OR KENWORTH AT 1-425-828-5440 OR PETERBILT AT 1-940-591-4196.
PACCAR IS RECALLING 172 MY 2007 KENWORTH T800 SHORT HOOD, W900 LONG HOOD AND T600 TRACTOR/TRAILERS EQUIPPED WITH SAF-HOLLAND SIMPLEX FIFTH WHEELS. IF THE PIVOT BOLT JOINT FOR THE LEVER BAR IS OVER TORQUED, THE SPACER DEFORMS, AND MAKES CONTACT WITH THE LEVER BAR. THIS CONDITION COUPLED WITH CORROSION ASSOCIATED WITH THE SEASONAL DRY OUT, CAN AFFECT THE LOCK SYSTEM OF THE FIFTH WHEEL, PREVENTING THE FIFTH WHEEL JAW FROM LATCHING SECURELY AROUND THE TRAILER KING PIN. Remedy: KENWORTH IS WORKING WITH SAF-HOLLAND SIMPLEX AND WILL INSPECT THE PIVOT BOLT JOINT FOR A DEFORMED SPACER AND REPLACE THE BOLT, WASHER AND SPACER WITH A HEX-HEAD SHOULDER BOLT AND WASHER FREE OF CHARGE. THE RECALL BEGAN ON MAY 1, 2008. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440 OR SAF-HOLLAND AT 1-231-773-3271.
PACCAR IS RECALLING 140 MY 2005, 2007-2009 T800, W900, AND T660 TRUCKS. THE CALIPER MOUNTING FASTENERS ATTACHING THE AIR DISC BRAKE CALIPER ASSEMBLY TO THE TORQUE PLATE MAY HAVE RECEIVED INSUFFICIENT TORQUE DURING THE INSTALLATION PROCESS. THE INSUFFICIENT TORQUE MAY ALLOW THE AIR DISC BRAKE CALIPER ASSEMBLY TO BECOME LOOSE AND POSSIBLY SEPARATE FROM THE VEHICLE. Remedy: DEALERS WILL INSPECT AIR DISC BRAKE CALIPER ASSEMBLIES AND REPLACE THE CALIPER MOUNTING FASTENERS AND TORQUE PROPERLY. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE MANUFACTURER HAS NOT YET PROVIDED AN OWNER NOTIFICATION SCHEDULE. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440.
PACCAR IS RECALLING CERTAIN MODEL YEAR 2008-2012 KENWORTH T2000, T660, T700, T800, AND W900, AS WELL AS MODEL YEAR 2009-2012 PETERBILT 365, 367, 384, 386, 387, 388, 389, AND 587 TRUCKS EQUIPPED WITH PACCAR MX ENGINES. THE OIL MODULE CENTRIFUGAL SPINNER FILTER CAP IN THE PACCAR MX ENGINE MAY BECOME LOOSE, POSSIBLY ALLOWING THE CAP TO COME OFF AND ENGINE OIL TO PARTIALLY DISCHARGE FROM THE OIL MODULE ONTO EXHAUST COMPONENTS. Remedy: DEALERS WILL RE-TORQUE THE OIL MODULE FILTER CAP AND INSTALL A SECONDARY RETENTION DEVICE ON THE SECONDARY CENTRIFUGAL SPINNER FILTER CAP. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING MARCH 2011. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440 AND PETERBILT AT 1-940-591-4196.
PACCAR IS RECALLING CERTAIN MODEL YEAR 2007-2008 KENWORTH AND PETERBILT VEHICLES MANUFACTURED FROM FEBRUARY 2, 2006 THROUGH APRIL 30, 2007. THE BEARING SURFACES OF THE EXTENDED LUBE UNIVERSAL JOINT THAT ATTACHES THE INTER-AXLE DRIVELINE TO THE DRIVE AXLE MAY BECOME PREMATURELY WORN DUE TO BREAKDOWN OF LUBRICATION AND/OR EXCESSIVE HEAT. PREMATURELY WORN BEARING SURFACES MAY RESULT IN THE U-JOINT BECOMING LOOSE AND/OR BINDING. THIS CONDITION MAY RESULT IN UNIVERSAL JOINT FAILURE, ALLOWING THE INTER-AXLE DRIVELINE TO DETACH FROM THE AXLE. Remedy: PACCAR IS WORKING WITH ITS SUPPLIER TO REMEDY THE VEHICLES FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING FEBRUARY 2011. OWNERS MAY CONTACT KENWORTH AT 425-828-5440 AND PETERBILT AT 940-591-4196.
PACCAR IS RECALLING 3,573 MY 2007 KENWORTH C500, T800, T600, T2000, AND W900 CHASSIS BUILT WITH PHILLIPS QCS II TRAILER CABLE CONNECTION AND TRAILER CABLE MOUNTING BRACKET WITH 'U-SHAPED' CUT OUT. CERTAIN TRAILER CABLE MOUNTING BRACKETS HAVE A 'U-SHAPED' CUT OUT THAT ONLY PARTIALLY SUPPORTS THE TRAILER CABLE CONNECTION. PARTIAL SUPPORT OF THE CABLE CONNECTION MAY ALLOW THE MOLDED BOOT AND ELECTRICAL GROUND PIN TO PARTIALLY OR COMPLETELY PULL AWAY FROM THE 7-WAY SOCKET. PARTIAL OR COMPLETE DETACHMENT OF THE CABLE CONNECTION CAN CAUSE REDUCED WATER RESISTANCE AND POTENTIAL LOSS OF ELECTRICAL GROUND. THERE IS ALSO A POSSIBILITY THE TRAILER LIGHTS MAY FAIL TO ILLUMINATE WITHOUT THE OPERATOR'S KNOWLEDGE. Remedy: DEALERS WILL INSTALL A REINFORCEMENT BRACKET BETWEEN THE FLEXIBLE BACK OF THE QCS II MOLDED BOOT AND THE FRAME BRACKET, AND REATTACH THE SUPPORTING BOLTS. THE RECALL BEGAN ON MAY MAY 30, 2008. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440.
PACCAR IS RECALLING 318 MY 2007-2009 KENWORTH T800, W900, AND PETERBILT 357, 365, 367, 378, 379, 384, 385, 386,388, AND 389 TRUCKS EQUIPPED WITH PREMIER TRAILER HITCH ASSEMBLIES. THE PINTLE HITCH ASSEMBLIES MAY HAVE BEEN MANUFACTURED IN A MANNER RESULTING IN A REDUCTION OF FATIGUE STRENGTH OF THE PIVOT PINS. Remedy: DEALERS WILL REPLACE THE POTENTIALLY DEFECTIVE PIVOT PIN FREE OF CHARGE. THE RECALL BEGAN ON APRIL 18, 2008. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440 OR PETERBILT AT 1-940-591-4196.
PACCAR IS RECALLING 130 MY 2004-2009 T2000, T800, T600, W900 AND T660 KENWORTH TRUCKS BUILT WITH AN AG400 REAR SUSPENSION, LONG STROKE BRAKE CHAMBERS, AND WIDE BASE TIRES (SUPER SINGLES). THESE VEHICLES MAY DEVELOP AN INCREASE IN LATERAL AND VERTICAL AXLE MOVEMENT. THIS MOVEMENT MAY CAUSE PART OR PARTS OF THE BRAKE ASSEMBLY (BRAKE CAM TUBE SUPPORT, BRAKE CHAMBER BRACKET, BRAKE CHAMBER, BRAKE SPIDER) TO DEVELOP FATIGUE CRACKS, POSSIBLY RESULTING IN THE FAILURE OF THE PART OR PARTS WITHIN THE BRAKE ASSEMBLY. Remedy: DEALERS WILL INSTALL THE CAM TUBE SUPPORT BRACKETS ON ALL OF THE REAR AXLE WHEEL ENDS. INSPECT THE REAR AXLE BRAKE ASSEMBLY AND REPLACE IT IF CRACKED. THE RECALL IS EXPECTED TO BEGIN DURING NOVEMBER 2008. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440.
KENWORTH IS RECALLING 3,423 MY 2004-2009 T2000, T800,T600, W900 AND T660 VEHICLES. INCREASED BRAKE EXCITATION IN A CERTAIN VEHICLE CONFIGURATION WHICH INCLUDES BENDIX DRUM BRAKES, WIDE BASE LOW PROFILE SINGLE TIRES, AND AN AG400 OR AG460 REAR SUSPENSION, DUE TO ITS UNIQUE BRAKE CLOCKING AND CAM TUBE LENGTH, CAN CAUSE FATIGUE AND CRACKING TO BRAKE ASSEMBLY COMPONENTS. Remedy: DEALERS WILL INSPECT THE REAR AXLE BRAKES ASSEMBLY, REPLACE CRACKED REAR AXLE BRAKES ASSEMBLY COMPONENTS WHERE REQUIRED, AND INSTALL CAM TUBE SUPPORT BRACKETS ON ALL REAR AXLE WHEEL ENDS FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN OR BEFORE JULY 25, 2009. OWNER MAY CONTACT KENWORTH AT 1-425-828-5440.
PACCAR IS RECALLING 130 MY 2005-2007 KENWORTH C500, T800, W900, AND PETERBILT MODELS 357 AND 379 TRACTOR TRAILERS EQUIPPED WITH FABCO SLACK ADJUSTERS ON SISU AXLES. THE SLACK ADJUSTERS MAY FAIL AS A RESULT OF A FATIGUE CRACK RENDERING THE SLACK ADJUSTER INOPERATIVE. THIS COULD REDUCE BRAKING EFFECTIVENESS. Remedy: DEALERS WILL INSPECT AND REPLACE THE SLACK ADJUSTERS FREE OF CHARGE. THE RECALL BEGAN ON MARCH 21, 2008. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440 AND PETERBILT AT 1-940-591-4196.
PACCAR IS RECALLING 292 AFTERMARKET SAF HOLLAND FIFTH WHEELS SOLD FOR USE ON MY 2007 KENWORTH T800 SHORT HOOD, W900 LONG HOOD AND T600 TRACTOR/TRAILERS. IF THE PIVOT BOLT JOINT FOR THE LEVER BAR IS OVER TORQUED, THE SPACER DEFORMS, AND MAKES CONTACT WITH THE LEVER BAR. THIS CONDITION COUPLED WITH CORROSION ASSOCIATED WITH THE SEASONAL DRY OUT, CAN AFFECT THE LOCK SYSTEM OF THE FIFTH WHEEL, PREVENTING THE FIFTH WHEEL JAW FROM LATCHING SECURELY AROUND THE TRAILER KING PIN. Remedy: PACCAR IS WORKING WITH SAF-HOLLAND AND WILL INSPECT THE PIVOT BOLT JOINT FOR A DEFORMED SPACER AND REPLACE THE BOLT, WASHER AND SPACER WITH A HEX-HEAD SHOULDER BOLT AND WASHER FREE OF CHARGE. THE MANUFACTURER HAS NOT YET PROVIDED AN OWNER NOTIFICATION SCHECDULE. OWNERS MAY CONTACT PACCAR AT 1-415-828-5000 OR SAF-HOLLAND AT 1-231-773-3271.
AN INCORRECT SWITCH WAS INSTALLED IN THE CRUISE CONTROL SYSTEM ON CERTAIN MODEL T300 TRUCKS. Remedy: KENWORTH WILL INSTALL THE CORRECT SENSOR SWITCH. THE RECALL BEGAN ON JANUARY 10, 2007. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440.
CERTAIN TRUCKS FAIL TO COMPLY WITH THE BRAKE TIMING REGULATORY REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS." THE BRAKE VALVE WAS MOVED TO THE OPPOSITE RAIL, INCREASING THE LENGTH OF THE AIR LINE, WHICH IN TURN INCREASED THE WHEELBASE REQUIRING A DUAL RELAY VALVE SYSTEM. THE VEHICLES WERE MANUFACTURED WITH A SINGLE VALVE SYSTEM. Remedy: DEALERS WILL CONVERT THE SINGLE RELAY VALVE TO A DUAL RELAY VALVE SYSTEM FREE OF CHARGE. THE RECALL BEGAN ON MAY 21, 2007. OWNERS MAY CONTACT KENWORTH AT 425-828-5440.
ON CERTAIN TRUCKS, THE AXLE HOUSINGS MAY HAVE BEEN MANUFACTURED WITH STEEL THAT WAS OUT OF SPECIFICATION WHICH COULD RESULT IN A FATIGUE FAILURE OVER TIME. Remedy: DEALERS WILL INSPECT AND REPLACE THE AXLES FREE OF CHARGE. THE RECALL BEGAN ON MAY 9, 2007. OWNERS MAY CONTACT KENWORTH AT 425-828-5440 AND PETERBILT AT 1-940-591-4196.
ON CERTAIN TRUCKS, IF THE IGNITION SWITCH IS TURNED ON PRIOR TO INITIAL START UP IN THE MANUFACTURING PLANT OR DURING THE FILTER REPLACEMENT IN THE FIELD, A SMALL FLAME WILL IGNITE WHEN THE FUEL IS ADDED TO PRIME THE SYSTEM. Remedy: DEALERS WILL INSPECT THE FILTER FOR THE DATE CODES OF THE SUSPECT FILTERS AND REPLACE THOSE HEATING ELEMENTS FREE OF CHARGE. THE RECALL BEGAN ON MARCH 21, 2007. OWNERS MAY CONTACT KENWORTH AT 425-828-5440 AND PETERBILT AT 940-591-4201.
ON CERTAIN TRUCKS EQUIPPED WITH CATERPILLAR C11, C13 OR C15 ENGINES, THE OIL FILL CAP CAN BECOME DISLODGED DUE TO CAP DAMAGE OR IMPROPER INSTALLATION AND BECOME LODGED IN THE U-JOINT OF THE STEERING DRIVELINE AND STEERING GEAR. Remedy: PACCAR IS WORKING WITH CATERPILLAR TO REPAIR THESE VEHICLES. REVISED OIL CAP RETENTION BASED ON THE ENGINE MODEL/CONFIGURATION WILL BE INCORPORATED TO PREVENT STEERING LOCK-UP. THE RECALL BEGAN DURING DECEMBER 2007. OWNERS MAY CONTACT CATERPILLAR AT 1-800-447-4986 OR KENWORTH AT 425-828-5440.
CERTAIN TRUCKS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS." THE TRAILER LIGHT LINE MAY HAVE BEEN ROUTED USING TOO TIGHT OF A BEND RADIUS. THIS ROUTING METHOD COULD CAUSE THE WIRES WITHIN THE HARNESS PLUG TO BE PULLED AWAY FROM THE CHASSIS PLUG RESULTING IN AN INTERMITTENT OR COMPLETE ELECTRICAL POWER LOSS TO THE TRAILER. Remedy: DEALERS WILL REROUTE THE LIGHT LINE TO ELIMINATE THE EXCESSIVE BEND RADIUS AND REPLACE ANY PLUG OR HARNESS THAT HAS BEEN DAMAGED FREE OF CHARGE. THE RECALL BEGAN ON APRIL 16, 2007. OWNER MAY CONTACT KENWORTH AT 425-828-5440.
ON CERTAIN TRUCKS, THE REMOVABLE TOW HITCH ,WHEN USED TO TOW OR LIFT A VEHICLE, CAN FAIL DUE TO DEFECTIVE MATERIAL IN THE TOW HITCH. Remedy: DEALERS WILL REPLACE THE TOW PIN ASSEMBLY FREE OF CHARGE. THE RECALL BEGAN ON SEPTEMBER 4, 2007. OWNERS MAY CONTACT KENWORTH AT 425-828-5440 OR PETERBILT AT 940-591-4201.
ON CERTAIN TRUCKS EQUIPPED WITH A TRW TILT/TELESCOPING STEERING COLUMN, THE TILT LOCKING MECHANISM ON THE STEERING COLUMN MAY DISENGAGE. THIS COULD PREVENT THE STEERING COLUMN FROM LOCKING IN TO PREDETERMINED POSITIONS. Remedy: DEALERS WILL REPLACE THE TILT LOCKING MECHANISM WITH A REVISED DESIGN THAT INCORPORATES A NEW BRACKET FOR RESTRAINING THE TILTING MECHANISM. THE RECALL BEGAN ON DECEMBER 22, 2006. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440.
ON CERTAIN TRUCKS, THE WIRING, PARTS, OR TRANSMISSION PROGRAMMING REQUIRED FOR THE AUTO NEUTRAL FEATURE TO FUNCTION AS DESIGNED WERE EITHER NOT INSTALLED, CONNECTED, OR PROGRAMMED PROPERLY. Remedy: DEALERS WILL INSPECT THE AFFECTED VEHICLES TO ENSURE THE AUTO NEUTRAL FEATURE FUNCTIONS PROPERLY AND, IF NEEDED, WILL MAKE THE NECESSARY REPAIRS FREE OF CHARGE. THE RECALL BEGAN ON MAY 9, 2007. OWNERS MAY CONTACT KENWORTH AT 425-828-5440.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Issue: This recall is for certain used trucks that Trojan Welding Inc. converted to dump trucks in 2019 and 2020. The company applied the National Safety Mark and a new compliance label that indicated the trucks were built in 2020. This is not allowed under the Motor Vehicle Safety Act. Safety Risk: Contrary to Trojan's labelling, the modified trucks do not meet all requirements under the Motor Vehicle Safety Act. Corrective Actions: Trojan Welding will notify the owner(s) in writing and arrange for the removal of the incorrect compliance label and National Safety Mark.
On certain trucks equipped with a Caterpillar C15 diesel engine, the Diesel Particulate Filter (DPF) combustion tube may fail. This could result in a vehicle fire causing property damage and/or personal injury. Correction: Dealers will replace the DPF combustion tube.
On certain vehicles equipped with a PACCAR MX engine, the oil module centrifugal spinner filter cap may become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto nearby exhaust components. The discharge of engine oil onto hot exhaust components could result in a fire causing property damage and/or personal injury. Correction: Dealers will re-torque the oil module filter cap and install a secondary retention device on the secondary centrifugal spinner filter cap.
On certain vehicles, the bearing surfaces of the extended lube universal joint that attaches the inter-axle driveline to the drive axle may become prematurely worn due to breakdown of the lubrification and/or excessive heat. Prematurely worn bearing surfaces may result in the u-joint becoming loose and/or binding. If undetected, the condition may result in universal joint failure, allowing the inter-axle driveline to detach from the axle, which may cause the vehicle to become disabled in the roadway. Lost propulsion, in conjunction with traffic, road conditions, and the driver's reactions, could increase the risk of a crash. In addition a driveline component separating from the vehicle could strike another vehicle, stationary object, or bystander, causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the interaxle driveline universal joint.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Certain vehicles may suffer cracking of various brake assembly components (i.e. brake cam tube mounting flanges, brake air chamber bracket, brake air chamber, brake spider). Over time, this cracking can cause a complete fracture of the cam tube, which could increase stopping distances and decrease parking brake hold capability. A reduction of braking capability could increase the risk of a crash causing property damage, personal injury or death. Correction: Dealers will inspect the rear axle brake assembly, replace cracked rear axle brake components where required, and install cam tube support brackets on all rear axle wheel ends.
On certain vehicles equipped with a Caterpillar C15 engine, the Variable Valve Actuation (VVA) oil line may wear against the P-clip retaining the oil line. An oil leak could result in a vehicle fire causing property damage and/or personal injury. Correction: Caterpillar dealers will replace the VVA oil line with an updated version.
On certain vehicles, the caliper mounting fasteners attaching the air disc brake caliper assembly to the torque plate may have received insufficient tightening torque during the assembly process. Insufficient torque may allow the caliper mounting fasteners and/or the caliper itself to become loose. This could cause the brake on the affected wheel end to become inoperable. Extended stopping distance could result in a vehicle crash causing property damage, personal injury or death. Correction: Dealers will replace caliper mounting fasteners and inspect the caliper assembly.
Certain vehicle configuration which includes an AG400 rear suspension, long stroke brake chambers, and wide base tires may develop an increase in lateral and vertical axle movement. This movement may cause part or parts of the brake assembly to develop fatigue cracks, possibly resulting in the failure of part or parts within the brake assembly. A failure may reduce vehicle brake performance, increasing the risk of a crash causing personal injury or death. Correction: Dealers will affect repairs.
On certain trucks, the inadequate stiffness of the Diesel Particulate Filter (DPF) bracket could result in the separation of the DPF from the chassis, which could result in personal injuries or death to motorists or bystanders. Correction: Caterpillar dealers will replace bracket as necessary.
On certain vehicles, the trailer cable mounting bracket has a "U-shaped" cut-out that only partially supports the trailer cable connection. This may allow the moulded boot and electrical ground pin to partially or completely pull away from the 7-way socket. Partial or complete detachment can cause reduced water resistance and potential loss of electrical ground. There is also a possibility the trailer lights may fail to illuminate without the operator's knowledge. Reduced visibility during hours of darkness could result in a vehicle crash, causing personal injury or death. Correction: Dealers will install a reinforcement bracket.
On certain vehicles, the slack adjuster may develop a fatigue crack and fail. This would render the slack adjuster inoperative, and reduce braking effectiveness. Extended stopping distances may result in a vehicle crash, causing property damage, and/or personal injury or death. Correction: Dealers will inspect and, where necessary, replace the slack adjusters.
On certain vehicles equipped with Caterpillar C7 and C9 diesel engines, fuel pump failure can dilute the engine oil with fuel and cause the turbocharger to fail, leading to a loss of throttle control and excessive smoke. Either condition could result in a vehicle crash causing property damage, personal injury or death. Correction: Authorized Caterpillar dealers will replace the fuel pump.
On certain trucks, the removable front tow hitch assembly may fail. This could result in personal injury or property damage if the assembly failed during the un-decking or towing of a vehicle. Correction: Dealers will replace the tow pin assembly with a revised version.
On certain trucks equipped with Caterpillar C11, C13 and C15 engines, the oil fill cap can become dislodged due to cap damage or improper installation. The cap can become lodged in the u-joint of the steering driveline and steering gear, causing difficulty steering the vehicle and/or complete steering lock-up. A loss of steering control can result in a vehicle crash causing injury or death. Correction: Dealers will install an oil cap retention chain to C11 engines and will modify the existing retention chain anchor point on C13 and C15 engine. Damaged oil fill caps will be replaced.
On certain trucks, when the ignition key is in the 'ON' position, the pre-heater, located in the fuel filter base, is energized. If this pre-heater is energized while maintenance is being performed on the fuel filter, diesel fuel could ignite within the filter housing. A fire within the fuel filter housing may spread possibly resulting in property damage or personal injury. Correction: Dealers will inspect and, if required, replace the fuel heater assembly.