Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2007 Mack CHN, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
ON CERTAIN TRUCKS EQUIPPED WITH SR-7 BENDIX BRAKE VALVES, THE CHECK VALVE INSIDE THE VALVE CAVITY MAY NOT PROPERLY SET, CAUSING INTERNAL AIR LEAKAGE. IF THE CHECK VALVE DOES NOT PROPERLY SEAT, THE RESULTING LEAKAGE CAN CAUSE A DELAY IN THE APPLICATION OF THE SPRING BRAKES TO PARK THE VEHICLE AFTER OPERATOR PULLS THE DASH VALVE BUTTON. Remedy: DEALERS WILL INSPECT THE VALVES AND REPLACE IT FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 14, 2006. OWNERS MAY CONTACT MACK TRUCKS AT 1-800-528-6586.
ON CERTAIN TRUCKS, THE FUEL LINE CROSSOVER BRACKET MAY PREMATURELY FAIL AND UNEXPECTEDLY FALL TO THE ROAD. THE LOCATION AND SIZE OF THE BRACKET DRAWS A CONCERN TO THE BRACKET BEING PICKED UP AND THROWN BY THE DRIVE AXLE WHEELS. Remedy: DEALERS WILL REPLACE THE BRACKETS FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 20, 2006. OWNERS MAY CONTACT MACK TRUCKS AT 1-800-528-6586.
ON CERTAIN TRUCKS, THE NUT THAT RETAINS THE STEERING WHEEL MAY NOT HAVE BEEN INSTALLED. Remedy: DEALERS WILL REMOVE THE HORN BUTTON TO CONFIRM THAT THE RETAINING NUT WAS INSTALLED. A RETAINING NUT WILL BE ADDED IF THE NUT IS MISSING. THE RECALL BEGAN ON FEBRUARY 12, 2007. OWNERS MAY CONTACT MACK TRUCKS AT 800-866-1177.
ON CERTAIN TRUCKS EQUIPPED WITH BENDIX SR-7 SPRING BRAKE MODULATING VALVES, THE INTERNAL RUBBER CHECK VALVE MAY LEAK CAUSING A DELAY IN THE APPLICATION OF THE SPRING BRAKES TO PARK THE VEHICLE AFTER THE OPERATOR PULLS THE DASH VALVE BUTTON. Remedy: MACK IS WORKING WITH BENDIX TO REPAIR THESE VEHICLES (PLEASE SEE 07E037). BENDIX WILL INSTALL A CHECK VALVE REPAIR KIT FOR THE AFFECTED SR-7 SPRING BRAKE MODULATING VALVE FREE OF CHARGE. THE RECALL BEGAN ON JANUARY 10, 2008. OWNERS MAY CONTACT BENDIX AT 1-440-329-9000 OR MACK AT 1-800-528-6586.
ON CERTAIN TRUCKS, THE AXLE HOUSINGS MAY HAVE BEEN MANUFACTURED WITH STEEL THAT WAS OUT OF SPECIFICATION WHICH COULD RESULT IN A FATIGUE FAILURE OVER TIME. Remedy: DEALERS WILL INSPECT AND REPLACE THE AXLES FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN ON OR ABOUT APRIL 9, 2007. OWNERS MAY CONTACT MACK TRUCKS AT 1-800-528-6586.
CERTAIN TRUCKS WERE RECALLED FOR THE INSTALLATION OF SLEEVES ON THE FUEL INJECTION LINE AS REQUIRED BY SAFETY RECALL SC0317 (NHTSA RECALL NO. 06V392). THERE IS A POSSIBILITY THAT THE NEW SLEEVES MAY CHAFE THE FUEL INJECTION LINE. Remedy: DEALERS WILL REMOVE THE PROTECTIVE SLEEVES ON ALL FUEL INJECTION LINES FREE OF CHARGE. THIS RECALL BEGAN ON APRIL 19, 2007. OWNERS MAY CONTACT MACK TRUCKS AT 1-800-528-6586.
ON CERTAIN TRUCKS, A LEAK IN THE ASET AC FUEL INJECTION LINE MAY SPRAY FUEL ON THE EXHAUST GAS RECIRCULATION PIPES THAT CARRY HOT EXHAUST GASES . Remedy: MACK HAS ISSUED A STOP WORK ON THIS CAMPAIGN UNDER FURTHER NOTICE (2-22-2007). THE REMEDY DOES NOT ADEQUATELY ADDRESS THE ISSUE ON ALL VEHICLES. MACK WILL RE-RELEASE THE RECALL IN THE NEAR FUTURE. (PLEASE SEE NHTSA NO. 07V159/MACK RECALL NO. SCO323 FOR VEHICLES THAT HAVE HAD THIS REPAIR ALREADY PERFORMED.) THIS RECALL HAS BEEN SUPERSEDED (PLEASE SEE 07V401/SC0324).
ON CERTAIN TRUCKS EQUIPPED WITH PARKER SINGLE CHECK VALVES (SCV) PROVIDED BY BENDIX. THE DEFECT EXISTS IN THE PARKER SCV THAT CONNECTS WITH THE SUPPLY PORT OF THE SR-7 SPRING BRAKE MODULATING VALVE. AFTER PROLONGED USE OF THE PARKER SCV, THE VALVE BODY RETAINER MAY BECOME EXCESSIVELY WORN AND EVENTUALLY BREAK APART. PIECES OF THE PARKER SCV CAN BECOME LODGED INSIDE THE SR-7 SPRING BRAKE MODULATING VALVE, POTENTIALLY CAUSING EITHER LEAKAGE OUT OF THE SR-7 VALVE OR PREVENTING AIR FROM PROPERLY EXHAUSTING FROM THE SR-7 VALVE. Remedy: MACK IS WORKING WITH BENDIX TO REPLACE THE PARKER SINGLE CHECK VALVE. THE RECALL BEGAN ON JANUARY 9, 2008. OWNERS MAY CONTACT BENDIX AT 1-440-329-9000 OR MACK AT 1-800-528-6586.
ON CERTAIN TRUCKS EQUIPPED WITH A SAF HOLLAND SIMPLEX FIFTH WHEEL, THE LEVER ARM PIVOT BOLT MAY HAVE BEEN OVER TIGHTENED. AN OVER TIGHTENED PIVOT BOLT CAN DISTORT THE PIVOT BOLT SPACER SLEEVE, WHICH MAY PREVENT THE FIFTH WHEEL LATCH JAW FROM CLOSING AND LATCHING SECURELY AROUND THE TRAILER KING PIN. Remedy: DEALERS WILL REPLACE THE PIVOT BOLT AND SLEEVE WITH A HEX HEAD SHOULDER BOLT AND WASHER FREE OF CHARGE. THE RECALL BEGAN ON JANUARY 28, 2008. OWNERS MAY CONTACT MACK TRUCKS AT 1-800-528-6586.
ON CERTAIN TRUCKS EQUIPPED WITH A LEGRIS AIR MANIFOLD, THE BRASS PUSH-TO-CONNECT CARTRIDGE MAY UNEXPECTEDLY SEPARATE FROM THE PLASTIC HOUSING. Remedy: DEALERS WILL REPLACE THE AIR MANIFOLD FREE OF CHARGE. THE RECALL BEGAN ON SEPTEMBER 27, 2006. OWNERS MAY CONTACT MACK TRUCKS AT 1-800-528-6586.
ON CERTAIN TRUCKS EQUIPPED WITH ASET AC MODEL ENGINES, THE ENGINE AS CONFIGURED WITH AN EXTERNAL EXHAUST GAS RECIRCULATION SYSTEM MAKES SERVICING THE FUEL INJECTION LINES DIFFICULT WHEN USING TRADITIONAL TOOLS. THEREFORE, IT IS POSSIBLE FOR FUEL LEAKS TO DEVELOP WHEN REMOVING AND INSTALLING THE FUEL INJECTION LINES. Remedy: DEALERS WILL REPLACE THE FUEL INJECTION LINES FREE OF CHARGE. NOTE: THIS RECALL SUPERSEDES A PREVIOUS CAMPAIGN CONDUCTED IN 2006 (PLEASE SEE 06V392). THE RECALL BEGAN ON SEPTEMBER 11, 2007, WITH SUBSEQUENT MAILINGS EVERY SIX WEEKS UNTIL APRIL 2008. OWNERS MAY CONTACT MACK AT 800-528-6586.
ON CERTAIN TRUCKS, THE BRAKE CAM TUBES ON THE STEER AND DRIVE AXLES MAY NOT HAVE BEEN GREASED. Remedy: DEALERS WILL ADD GREASE TO THE BRAKE CAM TUBES FREE OF CHARGE. THE RECALL BEGAN ON SEPTEMBER 29, 2006. OWNERS MAY CONTACT MACK AT 1-800-866-1177.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain trucks, the fifth wheel hitch assembly's lever arm may have been incorrectly installed during the manufacturing process. The lever arm pivot bolt may have been over-tightened which could distort the pivot bolt spacer sleeve and prevent the fifth wheel latch jaw from closing and latching securely around the trailer king pin. This could allow the towed unit to separate from the towing vehicle while underway, potentially causing a crash with injury or death. Correction: Dealers will replace the pivot bolt and sleeve with a hex head shoulder bolt and washer.
On certain trucks, the engine configuration makes servicing fuel injection lines difficult when using traditional tools. It is possible for fuel leaks to develop following recall campaign 2006258 (Mack SC0317) or when line removal is required to gain access to other engine components. Underhood fuel leakage could result in a vehicle fire. Correction: Dealers will install an updated fuel injection line that offers better clamping surface when torqued. This will be done using specially designed tools to ensure correct torque is applied.
On certain vehicles, the internal rubber check valve inside the Bendix SR-7 spring brake modulating valve can become deformed over time. The effect of this defect is intermittent and presents a potential delay or failure in applying the parking brakes; potentially resulting in a vehicle roll away. Should this occur, the unattended roll away vehicle could strike a bystander or cause property damage. Correction: Dealers will install a check valve repair kit, and replace the Parker single check valve.
On certain school and transit buses, the Parker single check valve (SCV) that connects with the supply port of the Bendix SR-7 spring brake modulating valve may become excessively worn and eventually break apart. Pieces of the Parker SCV can become lodge inside the SR-7 valve, possibly causing either leakage out of the SR-7 valve or preventing air from properly exhausting from the SR-7 valve. This condition can cause a delay in the application of the parking brakes, the spring brakes not fully releasing or loss of isolation between the primary and secondary circuits. These conditions can occur without warning, leading to unintended vehicle rollaway, brake drag, or in case of loss of primary circuit, inability to modulate the spring brakes. An unattended roll away vehicle could strike a bystander or cause property damage. Correction: Dealers will replace the single check valve (SCV).
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
On certain trucks, sleeves installed as a result of repairs associated with safety recall SC0317 (Transport Canada number 2006258) may chafe the fuel injection line. This may compromise the fuel line over time, which could result in a fire. Correction: Dealers will remove the fuel injection line sleeves.
On certain trucks, the axle housing may have been manufactured with steel that was out of specification (9.5mm thick instead of 11mm thick), which could result in a fatigue failure over time. If failure occurs, the axle may lock-up or the end of the axle could come off, which may result in a vehicle crash with injury or death. Correction: Dealers will inspect and, if required, replace the axles.
On certain trucks, the nut that retains the steering wheel may not have been installed, which may result in a loss of steering control and a crash. Correction: Dealers will inspect and, if missing, install a retaining nut.
On certain trucks, a leak in the fuel injection line may spray fuel on the Exhaust Gas Recirculation (EGR) pipes. The hot EGR pipes could ignite the fuel, causing an underhood fire. Correction: Dealers will inspect and, if required, replace the fuel injection lines. A protective sleeve will be installed over the lines. Note: Recall cancelled, see TC 2007102
On certain vehicles, the brake cam tubes on the steer and drive axles may not have been greased during vehicle assembly. As a result, the brake cam journal may corrode which may lead to the brakes dragging and could result in a vehicle fire. Correction: Dealers will remove, inspect and service the brake camshaft.
On certain vehicles, the fuel line crossover bracket may fail. Such a failure could allow the bracket to fall from the vehicle and damage a drive axle tire. Correction: Dealers will replace the bracket.
On certain vehicles, the air brake fittings may unexpectedly separate from the plastic housing. If the push-to-connect cartridge that supplies the air to the park brake chambers were to separate, the brakes could unexpectedly apply. Correction: Dealers will replace the air manifold.
Certain trucks equipped with Bendix SR-7 spring brake modulating valve may experience an internal air leak if the check valve fails to seat. This may cause a delay in the application of the parking spring brakes leading to an unintended vehicle rollaway. Correction: Dealers will replace the Bendix SR-7 valve and the Parker single check valve.