Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2007 Volvo VT, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
Volvo Trucks North America (Volvo) is recalling certain model year 2007-2014 VAH, VHD, VNL, VNM, and VT models. The affected vehicles were built without a redundant clutch disengagement switch. Without a redundant switch, a loss of signal from the brake air pressure switch can prevent the clutch from automatically disengaging when the brake is applied. Remedy: Volvo Trucks will notify owners and dealers will inspect and repair the vehicles if necessary. The recall began on August 26, 2013. Volvo's recall number is RVXX1303. Owners may contact Volvo at 1-336-393-2000.
VOLVO TRUCKS IS RECALLING CERTAIN MODEL YEAR 2007 AND 2009 VHD, MODEL YEAR 2006 THROUGH 2010 VN, AND MODEL YEAR 2007 THROUGH 2009 VT TRUCKS MANUFACTURED FROM NOVEMBER 7, 2005, THROUGH OCTOBER 30, 2009, EQUIPPED WITH AN AIR RELEASE FIFTH WHEEL. THE INVERSION VALVE ON THE FRAME MAY BE ORIENTATED WHERE CONTAMINANTS CAN ENTER THE VALVE THROUGH THE EXHAUST PORT. AS A RESULT, THE BRAKE VALVE MAY CORRODE. Remedy: DEALERS WILL INSPECT THE INVERSION VALVE AND REPLACE AS REQUIRED. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE FEBRUARY 18, 2011. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
VOLVO TRUCKS IS RECALLING 127,764 MY 2001-2008 VHD, VNL, VNM, AND MY 2005-2008 VT TRUCKS. A SEAL MAY FAIL ALLOWING WATER AND CONTAMINANTS TO SEEP INTO THE WINDSHIELD WIPER MOTOR. Remedy: VOLVO WILL REPLACE THE WIPER MOTOR FREE OF CHARGE. SINCE THIS RECALL INVOLVES A LARGE NUMBER OF VEHICLES, VOLVO WILL RELEASE THE RECALL IN STAGES AS PARTS ARE RECEIVED. PRIORITY WILL BE GIVEN TO THE VEHICLES LOCATED IN THE REGIONS/STATES THAT HAVE A CORROSIVE ENVIRONMENT. THE RECALL BEGAN ON SEPTEMBER 30, 2009. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
ON CERTAIN HEAVY DUTY CLASS 8 TRUCKS EQUIPPED WITH DANA STEERING SHAFTS, THERE IS A POTENTIAL THAT THE STEERING SHAFT PINCH BOLT HOLE MAY BE INCORRECTLY LOCATED. THE PINCH BOLT FITS INTO A GROOVE IN THE STEERING GEAR INPUT SHAFT TO ENSURE THAT THE STEERING SHAFT DOES NOT SEPARATE FROM THE STEERING GEAR IF THE PINCH BOLT COMES LOOSE. Remedy: DEALERS WILL INSPECT THE STEERING SHAFT AND REPLACE IT AS REQUIRED FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 28, 006. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
ON CERTAIN TRUCKS EQUIPPED WITH ARVINMERITOR RPL20 HIGH ANGLE INTERAXLE DRIVESHAFTS, AN IMPROPER SEATED OR MISSING SNAP RING CAN RESULT IN THE BEARING CUP TO SEPARATE FROM THE SLIP YOKE SUB-ASSEMBLY. THE UNIVERSAL JOINT CROSS COULD THEN CONTACT THE SLIP YOKE CASTING AND EVENTUALLY CAUSE THE EAR WORK TO FRACTURE. Remedy: DEALERS WILL INSPECT THE DRIVESHAFTS AND REPLACE THEM AS NEEDED. THE RECALL BEGAN ON OCTOBER 23, 2006. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
ON CERTAIN HEAVY DUTY TRUCKS, THE CIRCUIT PROTECTION (I.E. AUTOMATIC CIRCUIT BREAKERS) USED TO PROTECT THE VEHICLE LIGHTING SYSTEM MAY NOT PROVIDE ADEQUATE PROTECTION. Remedy: DEALERS WILL REPLACE THE CIRCUIT BREAKERS WITH FUSES. THE RECALL BEGAN ON FEBRUARY 25, 2008. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
ON CERTAIN TRUCKS, AN UNPROTECTED LEAD IN THE THERMOSWITCH OF THE HEATER MAY MAKE CONTACT WITH ANOTHER POST POSSIBLY CREATING A SHORT CIRCUIT, WHICH CAN RESULT IN CONTINUOUS OPERATION OF THE HEATING ELEMENT. Remedy: DEALERS WILL INSPECT THE THERMOSWITCH AND WILL REPLACE IT IF NECESSARY. THE RECALL BEGAN ON SEPTEMBER 10, 2007. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
ON CERTAIN TRUCKS EQUIPPED WITH A SAF HOLLAND SIMPLEX FIFTH WHEEL, THE LEVER ARM PIVOT BOLT MAY HAVE BEEN OVER TIGHTENED. AN OVER TIGHTENED PIVOT BOLT CAN DISTORT THE PIVOT BOLT SPACER SLEEVE, WHICH MAY PREVENT THE FIFTH WHEEL LATCH JAW FROM CLOSING AND LATCHING SECURELY AROUND THE TRAILER KING PIN. Remedy: DEALERS WILL REPLACE THE PIVOT BOLT AND SLEEVE WITH A HEX HEAD SHOULDER BOLT AND WASHER FREE OF CHARGE. THE RECALL BEGAN ON JANUARY 28, 2008. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
ON CERTAIN TRUCKS, THE NUT USED TO RETAIN THE STEERING SHAFT MAY OR MAY NOT BE A LOCK NUT THAT HAS THE LOCKING FEATURE. A LOCK NUT IS REQUIRED TO PROVIDE ADDITIONAL RESISTANCE TO ENSURE THAT THE NUT DOES NOT COME LOOSE. Remedy: DEALERS WILL REPLACE THE STEERING SHAFT PINCH BOLTS AND LOCKNUTS FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 24, 2007. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain vehicles, the secondary clutch disengagement switch may have been omitted during vehicle assembly or, in some instances, removed during servicing. As such, primary switch failure would cause the automated manual transmission’s clutch to remain engaged when the brakes are applied. This could increase stopping distances, possibly resulting in a crash causing property damage and/or personal injury. Correction: Dealers will install a micro-switch at the brake pedal and update the software to run a diagnostic on the switch during engine start-up.
On certain trucks equipped with an air release fifth wheel hitch, the inversion valve on the frame may be orientated where contaminants can enter the valve through the exhaust port. As a result, the brake valve may corrode causing it to malfunction and in some cases result in unintended opening of the fifth wheel's locking mechanism. This could allow the trailer to separate from the towing vehicle while underway. Also, an air loss could increase vehicle stopping distance and result in a crash causing property damage or personal injury. Correction: Dealers will inspect and replace the inversion valve if required.
On certain vehicles, the windshield wiper motor may be susceptible to water intrusion, which could result in an electrical short circuit and a fire. This could cause property damage, personal injury or death. Correction: Dealers will affect repairs.
On certain trucks, the automatic circuit breakers used to protect the vehicle lighting system may not provide adequate protection. If a short circuit occurs, components and wiring may be subject to overheating, which could result in a vehicle fire, causing property damage and/or personal injury or death. Correction: Dealers will replace the circuit breakers with fuses.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
On certain trucks, the fifth wheel hitch assembly's lever arm may have been incorrectly installed during the manufacturing process. The lever arm pivot bolt may have been over-tightened which could distort the pivot bolt spacer sleeve and prevent the fifth wheel latch jaw from closing and latching securely around the trailer king pin. This could allow the towed unit to separate from the towing vehicle while underway, potentially causing a crash with injury or death. Correction: Dealers will replace the pivot bolt and sleeve with a hex head shoulder bolt and washer.
On certain trucks, when the ignition key is in the 'ON' position, the pre-heater, located in the fuel filter base, is energized. If this pre-heater is energized while maintenance is being performed on the fuel filter, diesel fuel could ignite within the filter housing. A fire within the fuel filter housing may spread possibly resulting in property damage or personal injury. Correction: Dealers will inspect and, if required, replace the fuel heater assembly.
On certain trucks, the locknut used to retain the steering shaft may not have had the lock feature. As a result, the nut could loosen, allowing the steering shaft to separate, causing a loss of steering control which could result in a vehicle crash with injury or death. Correction: Dealers will replace the steering shaft pinch bolt and locknut.
On certain trucks, an improperly seated or missing u-joint snap ring can result in the bearing cup to separate from the slip yoke sub-assembly. The u-joint could then contact the slip yoke casting and eventually cause the ear to fracture. This could result in additional damage to the driveline, the vehicle and any nearby objects. Correction: Dealers will inspect and, if required, replace the driveshafts.
On certain vehicles, the steering shaft pinch bolt hole may be incorrectly located. As a result, the steering shaft may separate from the steering gear which could lead to a sudden loss of vehicle control and a crash. Correction: Dealers will inspect and, if required, replace the steering shaft.