Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2008 BMW K1200 S, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
BMW of North America, LLC (BMW) is recalling certain 2009-2011 K1300 (S, GT), 2010-2011 S1000 RR, 2005-2011 R1200 (GS, GS Adventure, R, RT, S, ST), 2006-2010 HP2 (Enduro, Megamoto, Sport), 2005-2008 K1200 (R, R Sport, S, GT), and 2012 K1600 (GT, GTL) motorcycles that were repaired under recall 13V-617 with the support ring remedy and where the fuel pump was not replaced at a later date. This recall involves the fuel pump, and also the auxiliary fuel pump as applicable. The affected motorcycles have a fuel pump flange that may crack, possibly resulting in a fuel leak while the engine is running. Remedy: BMW will notify owners, and dealers will replace the fuel pump(s) with an improved version, free of charge. The recall began January 18, 2021. Owners may contact BMW customer service at 1-800-525-7417.
BMW IS RECALLING 30 MY 2008 K1200 S AND K1200 GT MOTORCYCLES. A SET SCREW MAY NOT HAVE BEEN INSTALLED AT ITS SPECIFIC LOCATION WITHIN THE OIL DUCT. CONSEQUENTLY, AN ADEQUATE SUPPLY OF OIL MAY NOT CIRCULATE WITHIN THE ENGINE. Remedy: DEALERS WILL INSTALL A SET SCREW IN THE OIL DUCT. THE RECALL BEGAN DURING AUGUST 2008. OWNERS MAY CONTACT BMW AT 1-800-331-1117.
BMW is recalling certain model year 2007-2008 K1200 S, K1200 R, and K1200 R Sport motorcycles and 2012 and 2013 K1300 S motorcycles. In October 2012, BMW recalled 2062 2007-2008 K1200 S, K1200 R, and K1200 R Sport motorcycles. In November 2012, BMW informed the agency that it was adding model year 2012 and 2013 K1300 S (including HP Limited Edition) motorcycles to the recall campaign, representing an additional 421 units. The total number of motorcycles being recalled is now 2,483. In certain riding conditions, the brake fluid in the front brake fluid reservoir can foam. Remedy: The front brake fluid reservoir will be retrofitted with a screen insert, free of charge. The recall began on December 19, 2012. Owners may contact BMW at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
BMW IS RECALLING 548 MY 2008 K1200 S AND GT MOTORCYCLES. THE FASTENERS USED TO SECURE THE FRONT BRAKE-DISC MAY NOT BE LONG ENOUGH TO ENSURE A SECURE MOUNTING. OVER TIME, THESE FASTENERS COULD LOOSEN. IF THAT HAPPENED, THE BRAKE DISC WOULD NO LONGER BE SECURELY MOUNTED. Remedy: DEALERS WILL INSPECT AND INSTALL A LONGER FRONT BRAKE DISC FASTENERS AND REROUTE THE SENSOR CABLE FREE OF CHARGE. THE RECALL BEGAN DURING AUGUST 2008. OWNERS MAY CONTACT BMW AT 1-800-831-1117.
BMW IS RECALLING CERTAIN MODEL YEAR 2005-2011 MOTORCYCLES. THE BEARINGS COULD BE SUBJECT TO CORROSION. THIS COULD LEAD TO REDUCED MOVEMENT OF THE LINK LEVER. Remedy: BMW WILL NOTIFY OWNERS AND DEALERS WILL REPAIR THE VEHICLES FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING MARCH 2011. OWNERS MAY CONTACT BMW AT 1-800-525-7417.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Issue: On certain motorcycles, the fuel pump flange could crack. If this happens, fuel could leak while the engine is running. Note: This recall only affects motorcycles that did not have the fuel pump replaced under Transport Canada recall 2013-442. Safety Risk: A fuel leak can create the risk of a fire. Corrective Actions: BMW will notify owners by mail and instruct you to take your motorcycle to a dealer to replace the fuel pump and auxiliary fuel pump (if equipped) with an improved version.
Certain motorcycles with dealer installed accessory turn signals may not comply with the requirements of Canada Motor Vehicle Safety Standard (CVMSS) 108 - Lighting System and Retroreflective Devices. The size of the lens on the accessory turn signals may be too small, and therefore would not meet the requirements of the standard. This could reduce vehicle conspicuity to following and approaching road users, and increase the risk of a crash causing injury and/or property damage. Correction: Dealers will replace the accessory turn signals with factory indicators that meet the requirements of the standard.
On certain motorcycles, the threaded holes on the rear wheel flange could crack if the wheel bolts are tightened beyond the specified torque limit during servicing. Over time, this could allow the bolts to back out of their threaded holes, causing the rear wheel to become loose. This could result in a loss of stability of the motorcycle, and increase the risk of a crash causing injury and/or property damage. Correction: Dealers will replace the aluminum rear wheel flange with a steel flange.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
On certain motorcycles, cracks could develop in the fuel pump and/or auxiliary fuel pump flange (if equipped). This would result in fuel leaking when the engine is turned on and the fuel system is pressurized. Leaking fuel, in the presence of an ignition source, could lead to a fire causing injury and/or damage to property. Correction: Dealers will inspect the fuel pump flange(s) and install a reinforcing ring or replace the fuel pump(s), as necessary.
On certain motorcycles, vibration, particularly on a long ride at constant high engine rpm and on engine overrun at high rpm, can, under certain circumstances, cause foaming of the brake fluid in the reservoir of the front brakes. This foaming may cause air to enter into the brake system, which can severely diminish the braking efficiency of the front brakes. Extended stopping distance may result in a vehicle crash causing property damage and/or personal injury. Correction: Dealers will install a screen insert into the front brake fluid reservoir.
On certain motorcycles, due to environmental conditions, the bearings of the link lever attached to the rear strut could be subject to corrosion. This could lead to reduced movement of the link lever. Over time, if the corrosion became significant, restriction of movement of the link lever could occur. This could affect handling of the motorcycle. In an extreme case, this could result in the connecting rod breaking by a bending force, causing the rear wheel to decelerate by contact with the inner fender. This could lead to a crash depending on traffic, road conditions and rider's reactions. Correction: Dealers will replace the rear suspension relay lever.