Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2008 Kenworth W900, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
ON CERTAIN TRUCKS, THE AXLE HOUSINGS MAY HAVE BEEN MANUFACTURED WITH STEEL THAT WAS OUT OF SPECIFICATION WHICH COULD RESULT IN A FATIGUE FAILURE OVER TIME. Remedy: DEALERS WILL INSPECT AND REPLACE THE AXLES FREE OF CHARGE. THE RECALL BEGAN ON MAY 9, 2007. OWNERS MAY CONTACT KENWORTH AT 425-828-5440 AND PETERBILT AT 1-940-591-4196.
ON CERTAIN TRUCKS, IF THE IGNITION SWITCH IS TURNED ON PRIOR TO INITIAL START UP IN THE MANUFACTURING PLANT OR DURING THE FILTER REPLACEMENT IN THE FIELD, A SMALL FLAME WILL IGNITE WHEN THE FUEL IS ADDED TO PRIME THE SYSTEM. Remedy: DEALERS WILL INSPECT THE FILTER FOR THE DATE CODES OF THE SUSPECT FILTERS AND REPLACE THOSE HEATING ELEMENTS FREE OF CHARGE. THE RECALL BEGAN ON MARCH 21, 2007. OWNERS MAY CONTACT KENWORTH AT 425-828-5440 AND PETERBILT AT 940-591-4201.
ON CERTAIN TRUCKS EQUIPPED WITH A TRW TILT/TELESCOPING STEERING COLUMN, THE TILT LOCKING MECHANISM ON THE STEERING COLUMN MAY DISENGAGE. THIS COULD PREVENT THE STEERING COLUMN FROM LOCKING IN TO PREDETERMINED POSITIONS. Remedy: DEALERS WILL REPLACE THE TILT LOCKING MECHANISM WITH A REVISED DESIGN THAT INCORPORATES A NEW BRACKET FOR RESTRAINING THE TILTING MECHANISM. THE RECALL BEGAN ON DECEMBER 22, 2006. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440.
ON CERTAIN TRUCKS, THE WIRING, PARTS, OR TRANSMISSION PROGRAMMING REQUIRED FOR THE AUTO NEUTRAL FEATURE TO FUNCTION AS DESIGNED WERE EITHER NOT INSTALLED, CONNECTED, OR PROGRAMMED PROPERLY. Remedy: DEALERS WILL INSPECT THE AFFECTED VEHICLES TO ENSURE THE AUTO NEUTRAL FEATURE FUNCTIONS PROPERLY AND, IF NEEDED, WILL MAKE THE NECESSARY REPAIRS FREE OF CHARGE. THE RECALL BEGAN ON MAY 9, 2007. OWNERS MAY CONTACT KENWORTH AT 425-828-5440.
PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles." Remedy: PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.
PACCAR is recalling certain model year 2007-2014 Kenworth T800 and W900 trucks manufactured March 22, 2006, through July 15, 2013 and equipped with Primaax tridem rear suspensions and a pusher and/or tag axle. The affected trucks have brake chambers that take longer to apply or release the brakes than the required time limit. Thus, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 121, "Air Brake Systems." Remedy: PACCAR will notify owners, and dealers will modify the air brake system, free of charge. The recall began on January 15, 2014. Owners may contact PACCAR at 1-425-468-7400. Kenworth's recall number is 13KWL.
PACCAR IS RECALLING 4,883 MY 2006-2009 KENWORTH T600, T660, T800, W900, T2000 AND MY 2008-2009 PETERBILT 365, 367, 379, 384, 386, 387, 388 AND 389 TRUCKS. INADEQUATE STIFFNESS OF THE DIESEL PARTICULATE FILTER (DPF) BRACKET COULD RESULT IN SEPARATION OF THE DPF FROM THE CHASSIS. Remedy: PACCAR IS WORKING WITH CATERPILLAR TO REPAIR THESE VEHICLES (PLEASE SEE 08E041). OWNERS MAY CONTACT CATERPILLAR AT 1-800-447-4986 OR KENWORTH AT 1-425-828-5440 OR PETERBILT AT 1-940-591-4196.
PACCAR IS RECALLING 140 MY 2005, 2007-2009 T800, W900, AND T660 TRUCKS. THE CALIPER MOUNTING FASTENERS ATTACHING THE AIR DISC BRAKE CALIPER ASSEMBLY TO THE TORQUE PLATE MAY HAVE RECEIVED INSUFFICIENT TORQUE DURING THE INSTALLATION PROCESS. THE INSUFFICIENT TORQUE MAY ALLOW THE AIR DISC BRAKE CALIPER ASSEMBLY TO BECOME LOOSE AND POSSIBLY SEPARATE FROM THE VEHICLE. Remedy: DEALERS WILL INSPECT AIR DISC BRAKE CALIPER ASSEMBLIES AND REPLACE THE CALIPER MOUNTING FASTENERS AND TORQUE PROPERLY. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE MANUFACTURER HAS NOT YET PROVIDED AN OWNER NOTIFICATION SCHEDULE. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440.
PACCAR IS RECALLING CERTAIN MODEL YEAR 2008-2012 KENWORTH T2000, T660, T700, T800, AND W900, AS WELL AS MODEL YEAR 2009-2012 PETERBILT 365, 367, 384, 386, 387, 388, 389, AND 587 TRUCKS EQUIPPED WITH PACCAR MX ENGINES. THE OIL MODULE CENTRIFUGAL SPINNER FILTER CAP IN THE PACCAR MX ENGINE MAY BECOME LOOSE, POSSIBLY ALLOWING THE CAP TO COME OFF AND ENGINE OIL TO PARTIALLY DISCHARGE FROM THE OIL MODULE ONTO EXHAUST COMPONENTS. Remedy: DEALERS WILL RE-TORQUE THE OIL MODULE FILTER CAP AND INSTALL A SECONDARY RETENTION DEVICE ON THE SECONDARY CENTRIFUGAL SPINNER FILTER CAP. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING MARCH 2011. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440 AND PETERBILT AT 1-940-591-4196.
PACCAR IS RECALLING CERTAIN MODEL YEAR 2007-2008 KENWORTH AND PETERBILT VEHICLES MANUFACTURED FROM FEBRUARY 2, 2006 THROUGH APRIL 30, 2007. THE BEARING SURFACES OF THE EXTENDED LUBE UNIVERSAL JOINT THAT ATTACHES THE INTER-AXLE DRIVELINE TO THE DRIVE AXLE MAY BECOME PREMATURELY WORN DUE TO BREAKDOWN OF LUBRICATION AND/OR EXCESSIVE HEAT. PREMATURELY WORN BEARING SURFACES MAY RESULT IN THE U-JOINT BECOMING LOOSE AND/OR BINDING. THIS CONDITION MAY RESULT IN UNIVERSAL JOINT FAILURE, ALLOWING THE INTER-AXLE DRIVELINE TO DETACH FROM THE AXLE. Remedy: PACCAR IS WORKING WITH ITS SUPPLIER TO REMEDY THE VEHICLES FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING FEBRUARY 2011. OWNERS MAY CONTACT KENWORTH AT 425-828-5440 AND PETERBILT AT 940-591-4196.
PACCAR IS RECALLING 318 MY 2007-2009 KENWORTH T800, W900, AND PETERBILT 357, 365, 367, 378, 379, 384, 385, 386,388, AND 389 TRUCKS EQUIPPED WITH PREMIER TRAILER HITCH ASSEMBLIES. THE PINTLE HITCH ASSEMBLIES MAY HAVE BEEN MANUFACTURED IN A MANNER RESULTING IN A REDUCTION OF FATIGUE STRENGTH OF THE PIVOT PINS. Remedy: DEALERS WILL REPLACE THE POTENTIALLY DEFECTIVE PIVOT PIN FREE OF CHARGE. THE RECALL BEGAN ON APRIL 18, 2008. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440 OR PETERBILT AT 1-940-591-4196.
PACCAR IS RECALLING 130 MY 2004-2009 T2000, T800, T600, W900 AND T660 KENWORTH TRUCKS BUILT WITH AN AG400 REAR SUSPENSION, LONG STROKE BRAKE CHAMBERS, AND WIDE BASE TIRES (SUPER SINGLES). THESE VEHICLES MAY DEVELOP AN INCREASE IN LATERAL AND VERTICAL AXLE MOVEMENT. THIS MOVEMENT MAY CAUSE PART OR PARTS OF THE BRAKE ASSEMBLY (BRAKE CAM TUBE SUPPORT, BRAKE CHAMBER BRACKET, BRAKE CHAMBER, BRAKE SPIDER) TO DEVELOP FATIGUE CRACKS, POSSIBLY RESULTING IN THE FAILURE OF THE PART OR PARTS WITHIN THE BRAKE ASSEMBLY. Remedy: DEALERS WILL INSTALL THE CAM TUBE SUPPORT BRACKETS ON ALL OF THE REAR AXLE WHEEL ENDS. INSPECT THE REAR AXLE BRAKE ASSEMBLY AND REPLACE IT IF CRACKED. THE RECALL IS EXPECTED TO BEGIN DURING NOVEMBER 2008. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440.
KENWORTH IS RECALLING 3,423 MY 2004-2009 T2000, T800,T600, W900 AND T660 VEHICLES. INCREASED BRAKE EXCITATION IN A CERTAIN VEHICLE CONFIGURATION WHICH INCLUDES BENDIX DRUM BRAKES, WIDE BASE LOW PROFILE SINGLE TIRES, AND AN AG400 OR AG460 REAR SUSPENSION, DUE TO ITS UNIQUE BRAKE CLOCKING AND CAM TUBE LENGTH, CAN CAUSE FATIGUE AND CRACKING TO BRAKE ASSEMBLY COMPONENTS. Remedy: DEALERS WILL INSPECT THE REAR AXLE BRAKES ASSEMBLY, REPLACE CRACKED REAR AXLE BRAKES ASSEMBLY COMPONENTS WHERE REQUIRED, AND INSTALL CAM TUBE SUPPORT BRACKETS ON ALL REAR AXLE WHEEL ENDS FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN OR BEFORE JULY 25, 2009. OWNER MAY CONTACT KENWORTH AT 1-425-828-5440.
PACCAR IS RECALLING 1098 KENWORTH MY 2008 T800, W900, MY 2008-2009 T2000 AND PETERBILT MY 2007-2009 379 AND 387 TRUCKS EQUIPPED WITH C15 CATERPILLAR DIESEL ENGINES. THE AFTERTREATMENT REGENERATION DEVICE (ARD) MAY DEVELOP A HOLE AND HEAT AND FLAME MAY ESCAPE DURING A REGENERATION OF THE DIESEL PARTICULATE FILTER. Remedy: PACCAR IS WORKING WITH CATERPILLAR AND WILL INSPECT AND REMEDY THE ENGINES FREE OF CHARGE. OWNERS MAY CONTACT CATERPILLAR AT 1-800-447-4986, KENWORTH AT 425-828-5440 OR PETERBILT AT 940-591-4196.
PACCAR IS RECALLING CERTAIN MODEL YEAR 2008-2010 TRUCKS EQUIPPED WITH TRW STEERING SHAFTS. THE CIRCUMFERENTIAL WELD AROUND THE STEERING SHAFT TUBE THAT WELDS THE SPLINED TUBE TO THE NON-SPLINED TUBE MAY BE MISLOCATED. MISLOCATION OF THE CIRCUMFERENTIAL WELD MAY ALLOW THE SPLINED TUBE AND NON-SPLINED TUBE TO ROTATE RELATIVE TO ONE ANOTHER DURING A LOW SPEED, HIGH TORQUE TURN, POSSIBLY RESULTING IN A SEPARATION OF THE TWO TUBES. Remedy: DEALERS WILL INSPECT THE STEERING SHAFT USING A WELD PLACEMENT GAUGE PROVIDED BY TRW. ANY STEERING SHAFT FOUND TO HAVE BEEN WELDED IMPROPERLY WILL BE REPLACED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JULY 30, 2010. OWNERS MAY CONTACT KENWORTH AT 425-828-5440 AND PETERBILT AT 940-591-4196.
CERTAIN TRUCKS EQUIPPED WITH EATON SYNFLEX ECLIPSE BRAND EXTRUDED NYLON AIR BRAKE HOSE TUBING FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 106, "BRAKE HOSES." THE TUBING WAS MANUFACTURED WITH ONLY FOUR LAYERS OF NYLON MATERIAL, INSTEAD OF THE SPECIFIED FIVE LAYERS. Remedy: DEALERS WILL INSPECT THE AIR BRAKE HOSES AND, IF NECESSARY, REPLACE THE HOSES. THE RECALL BEGAN ON FEBRUARY 22, 2008. OWNER NOTIFICATION SCHEDULE FOR THIS CAMPAIGN. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440 OR PETERBILT AT 1-940-591-4196.
PACCAR IS RECALLING 263 MY 2008-2009 KENWORTH T800, W900 AND PETERBILT 365 AND 384 TRUCKS EQUIPPED WITH C7 OR C9 CATERPILLAR DIESEL ENGINES. THE FUEL PUMP OUTLET CHECK PLUG MAY BE CRACKED WHICH COULD CAUSE FUEL TO SPRAY AND LEAK. Remedy: PACCAR IS WORKING WITH CATERPILLAR (PLEASE SEE 08E042). CATERPILLAR WILL REPLACE THE FUEL PUMP PLUG FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING SEPTEMBER 2008. OWNERS MAY CONTACT CATERPILLAR AT-1-800-447-4986 OR KENWORTH AT 1-425-828-5440 OR PETERBILT AT 1-940-591-4196.
PACCAR IS RECALLING 1,043 MY 2008-2009 KENWORTH C500, T2000,T660, T800 AND W900 TRUCKS EQUIPPED WITH BENDIX MV-3 DASH CONTROL VALVES. THE MOLDED VALVE BODY HAS AN INCORRECT CORE PIN IN THE INJECTION MOLD CAUSING THE VALVE BODY TO BE OVERSIZED IN THE DOUBLE CHECK VALVE AREA. THIS CONDITION CAN ALLOW THE RUBBER DOUBLE CHECK VALVE TO BECOME LODGED IN THE BODY OPENING UNDER CERTAIN CIRCUMSTANCES. Remedy: DEALERS WILL REPLACE THE BENDIX MV-3 DASH CONTROL VALVES FREE OF CHARGE. THE RECALL BEGAN ON APRIL 14, 2008. OWNERS MAY CONTACT KENWORTH AT 1-425-828-4196.
PACCAR IS RECALLING 6,169 MY 2008 KENWORTH T300, T660, T800, T2000, W900 AND C500 VEHICLES AND MY 2008-2009 PETERBILT MODELS 365, 367, 384, 387, 388, 389 AND 389 KITS. CERTAIN DOOR LATCH ASSEMBLIES ON THESE VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 206, 'DOOR LOCKS AND DOOR RETENTION COMPONENTS." THE ROTOR IN SOME OF THESE DOOR LATCH ASSEMBLIES DID NOT RECEIVE THE PROPER HEAT TREATMENT AND MAY BE SOFT. Remedy: PACCAR IS WORKING WITH TRIMARK AND WILL INSPECT AND REPLACE THE DOOR LATCH IF IT IS FOUND TO BE DEFECTIVE. THE RECALL BEGAN ON MARCH 14, 2008. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440 OR PETERBILT AT 1-940-591-4196.
CERTAIN TRUCK EQUIPPED WITH BEHR CABLES, THE CABLES WERE INSTALLED INCORRECTLY AND ARE TOO LONG. Remedy: DEALERS WILL INSPECT AND REPLACE ANY CABLE THAT ARE LONG FREE OF CHARGE. THE RECALL BEGAN ON APRIL 27, 2007. OWNERS MAY CONTACT KENWORTH AT 425-828-5440.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Issue: On certain trucks, the warning light for the tractor anti-lock brake system (ABS) may not turn on if the system loses power. If this happens, the driver will not get warning that the ABS is not working properly. Note: This problem would also cause the traction control (TC) and electronic stability control (ESC) lights not to turn on. Safety Risk: If a driver is not warned that the ABS is not working properly, there could be an increased risk of a crash. Corrective Actions: PACCAR will notify owners by mail and instruct you to take your truck to a dealer to update the software for the cab control module (CECU).
On certain trucks equipped with a Caterpillar C15 diesel engine, the Diesel Particulate Filter (DPF) combustion tube may fail. This could result in a vehicle fire causing property damage and/or personal injury. Correction: Dealers will replace the DPF combustion tube.
On certain vehicles equipped with a PACCAR MX engine, the oil module centrifugal spinner filter cap may become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto nearby exhaust components. The discharge of engine oil onto hot exhaust components could result in a fire causing property damage and/or personal injury. Correction: Dealers will re-torque the oil module filter cap and install a secondary retention device on the secondary centrifugal spinner filter cap.
On certain vehicles, the bearing surfaces of the extended lube universal joint that attaches the inter-axle driveline to the drive axle may become prematurely worn due to breakdown of the lubrification and/or excessive heat. Prematurely worn bearing surfaces may result in the u-joint becoming loose and/or binding. If undetected, the condition may result in universal joint failure, allowing the inter-axle driveline to detach from the axle, which may cause the vehicle to become disabled in the roadway. Lost propulsion, in conjunction with traffic, road conditions, and the driver's reactions, could increase the risk of a crash. In addition a driveline component separating from the vehicle could strike another vehicle, stationary object, or bystander, causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the interaxle driveline universal joint.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
On certain trucks, the weld around the steering shaft tube, which joins the splined tube to the non-splined intermediate tube, may be mislocated. An improperly located weld bead may allow the splined tube and non-splined tube to rotate relative one another during a low speed, high torque turn, resulting in a possible separation of the tubes. This could cause a loss of steering control which could result in a crash causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the steering shaft.
Certain vehicles may suffer cracking of various brake assembly components (i.e. brake cam tube mounting flanges, brake air chamber bracket, brake air chamber, brake spider). Over time, this cracking can cause a complete fracture of the cam tube, which could increase stopping distances and decrease parking brake hold capability. A reduction of braking capability could increase the risk of a crash causing property damage, personal injury or death. Correction: Dealers will inspect the rear axle brake assembly, replace cracked rear axle brake components where required, and install cam tube support brackets on all rear axle wheel ends.
On certain vehicles equipped with a Caterpillar C15 engine, the Variable Valve Actuation (VVA) oil line may wear against the P-clip retaining the oil line. An oil leak could result in a vehicle fire causing property damage and/or personal injury. Correction: Caterpillar dealers will replace the VVA oil line with an updated version.
On certain vehicles, the caliper mounting fasteners attaching the air disc brake caliper assembly to the torque plate may have received insufficient tightening torque during the assembly process. Insufficient torque may allow the caliper mounting fasteners and/or the caliper itself to become loose. This could cause the brake on the affected wheel end to become inoperable. Extended stopping distance could result in a vehicle crash causing property damage, personal injury or death. Correction: Dealers will replace caliper mounting fasteners and inspect the caliper assembly.
On certain vehicles, the Aftertreatment Regeneration Device (ARD) may develop a hole allowing heat and flame to escape during a regeneration of the Diesel Particulate Filter (DPF). This condition could result in a fire causing property damage and/or personal injury. Correction: Dealers will affect repairs.
Certain vehicle configuration which includes an AG400 rear suspension, long stroke brake chambers, and wide base tires may develop an increase in lateral and vertical axle movement. This movement may cause part or parts of the brake assembly to develop fatigue cracks, possibly resulting in the failure of part or parts within the brake assembly. A failure may reduce vehicle brake performance, increasing the risk of a crash causing personal injury or death. Correction: Dealers will affect repairs.
On certain trucks equipped with a Caterpillar C9 diesel engine, the fuel pump outlet check plug may crack and cause fuel to spray and leak from the fuel pump which may create a fire hazard. Correction: Caterpillar dealers will replace the fuel pump plugs.
On certain trucks, the inadequate stiffness of the Diesel Particulate Filter (DPF) bracket could result in the separation of the DPF from the chassis, which could result in personal injuries or death to motorists or bystanders. Correction: Caterpillar dealers will replace bracket as necessary.
Certain vehicles may have been assembled with an incorrectly manufactured Bendix MV-3 dash control valve. If the double check valve becomes lodged, in the event of a primary reservoir failure, air pressure can leak past the lodged valve, thereby depleting the secondary reservoir, causing a reduced ability for modulating the emergency brakes. Extended stopping distances may result in a vehicle crash, causing property damage, and/or personal injury or death. Correction: Dealers will inspect and, if necessary, replace the dash control valve.
On certain vehicles, the door latch may have been manufactured incorrectly. If the latch rotor cracks, the latch would not have primary or secondary closing security. Attempting to drive a vehicle with a door in the unlatched position can result in increased risk of injury to an unbelted front seat occupant. Correction: Dealers will inspect and, if necessary, replace the latch assemblies.
Certain vehicles fail to comply with requirements of CMVSS 121 - Air Brake System. The air lines were incorrectly constructed with only four layers of extruded nylon material, instead of the specified five layers. Should the air lines develop a leak, while the vehicle is in motion, it could cause the air brake system to fail, which would engage the rear spring brakes, slowing the vehicle to a stop, and preventing it from being driven. Correction: Dealers will inspect and, if required, replace the air lines.