Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2008 Peterbilt 389, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles." Remedy: PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.
PACCAR Incorporated (PACCAR) is recalling certain model year 2006-2016 Peterbilt 587, 579, 567, 389, 388, 387, 385, 382, 379, 378, 367, 365 and 357 trucks manufactured July 25, 2005, to February 26, 2016. The affected vehicles may be equipped with Tire and Rim Certification Labels that list a tire pressure below the actual correct amount. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard No. 120, "Tire selection and rims and motor home/recreation vehicle trailer load carrying capacity information for motor vehicles with a GVWR of more than 4,536 kilograms (10,000 pounds)." Remedy: Peterbilt will notify owners and mail them a corrected Tire and Rim certification label, free of charge. The recall began on June 19, 2015. Owners may contact Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 215-D.
PACCAR, Inc. (PACCAR) is recalling certain model year 2008-2013 Peterbilt 365, 367, 388, 389 trucks manufactured October 6, 2007, through September 23, 2013. The affected vehicles were built with 16.5" x 7" front drum brakes and Bendix ES-420 brake linings installed on front axles rated to carry between 20,001 and 22,000 lbs GAWR and larger SLR (20.5" to 21.5") tires, however these brake linings are not rated for this configuration. Thus, these vehicles fail to comply with Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems." Remedy: PACCAR will notify owners and dealers will install new 16.5" x 7" brake shoes with ES-600 linings, free of charge. The recall began on June 20, 2014. Owners may contact at Peterbilt at 1-800-473-8372. Peterbilt's number for this recall is 314-D.
PACCAR IS RECALLING 4,883 MY 2006-2009 KENWORTH T600, T660, T800, W900, T2000 AND MY 2008-2009 PETERBILT 365, 367, 379, 384, 386, 387, 388 AND 389 TRUCKS. INADEQUATE STIFFNESS OF THE DIESEL PARTICULATE FILTER (DPF) BRACKET COULD RESULT IN SEPARATION OF THE DPF FROM THE CHASSIS. Remedy: PACCAR IS WORKING WITH CATERPILLAR TO REPAIR THESE VEHICLES (PLEASE SEE 08E041). OWNERS MAY CONTACT CATERPILLAR AT 1-800-447-4986 OR KENWORTH AT 1-425-828-5440 OR PETERBILT AT 1-940-591-4196.
Paccar Incorporated (Paccar) is recalling certain 2004-2013 Peterbilt 379, 357, 378, 367, 388, 365, 389, 385 and 386 trucks manufactured from April 3, 2003, through October 25, 2013 and equipped with tri-drive rear axles and a tag or pusher axle. The affected vehicles may be missing required information from the certification label, specifically the tag or pusher axle the gross axle weight rating, suitable tire and rim information, and recommended tire pressure information. Without this information, the vehicles do not comply with the requirements of 49 C.F.R. Part 567, "Certification." Remedy: Peterbilt will notify owners and dealers will inspect and replace the certification labels missing the necessary information. The recall is expected to begin in January 2014. Customers can contact Peterbilt at 1-940-591-4000. Peterbilt's number for this campaign is 1113-F.
PACCAR IS RECALLING CERTAIN MODEL YEAR 2008-2012 KENWORTH T2000, T660, T700, T800, AND W900, AS WELL AS MODEL YEAR 2009-2012 PETERBILT 365, 367, 384, 386, 387, 388, 389, AND 587 TRUCKS EQUIPPED WITH PACCAR MX ENGINES. THE OIL MODULE CENTRIFUGAL SPINNER FILTER CAP IN THE PACCAR MX ENGINE MAY BECOME LOOSE, POSSIBLY ALLOWING THE CAP TO COME OFF AND ENGINE OIL TO PARTIALLY DISCHARGE FROM THE OIL MODULE ONTO EXHAUST COMPONENTS. Remedy: DEALERS WILL RE-TORQUE THE OIL MODULE FILTER CAP AND INSTALL A SECONDARY RETENTION DEVICE ON THE SECONDARY CENTRIFUGAL SPINNER FILTER CAP. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING MARCH 2011. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440 AND PETERBILT AT 1-940-591-4196.
PACCAR IS RECALLING CERTAIN MODEL YEAR 2007-2008 KENWORTH AND PETERBILT VEHICLES MANUFACTURED FROM FEBRUARY 2, 2006 THROUGH APRIL 30, 2007. THE BEARING SURFACES OF THE EXTENDED LUBE UNIVERSAL JOINT THAT ATTACHES THE INTER-AXLE DRIVELINE TO THE DRIVE AXLE MAY BECOME PREMATURELY WORN DUE TO BREAKDOWN OF LUBRICATION AND/OR EXCESSIVE HEAT. PREMATURELY WORN BEARING SURFACES MAY RESULT IN THE U-JOINT BECOMING LOOSE AND/OR BINDING. THIS CONDITION MAY RESULT IN UNIVERSAL JOINT FAILURE, ALLOWING THE INTER-AXLE DRIVELINE TO DETACH FROM THE AXLE. Remedy: PACCAR IS WORKING WITH ITS SUPPLIER TO REMEDY THE VEHICLES FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING FEBRUARY 2011. OWNERS MAY CONTACT KENWORTH AT 425-828-5440 AND PETERBILT AT 940-591-4196.
PACCAR IS RECALLING 6,169 MY 2008 KENWORTH T300, T660, T800, T2000, W900 AND C500 VEHICLES AND MY 2008-2009 PETERBILT MODELS 365, 367, 384, 387, 388, 389 AND 389 KITS. CERTAIN DOOR LATCH ASSEMBLIES ON THESE VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 206, 'DOOR LOCKS AND DOOR RETENTION COMPONENTS." THE ROTOR IN SOME OF THESE DOOR LATCH ASSEMBLIES DID NOT RECEIVE THE PROPER HEAT TREATMENT AND MAY BE SOFT. Remedy: PACCAR IS WORKING WITH TRIMARK AND WILL INSPECT AND REPLACE THE DOOR LATCH IF IT IS FOUND TO BE DEFECTIVE. THE RECALL BEGAN ON MARCH 14, 2008. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440 OR PETERBILT AT 1-940-591-4196.
PACCAR IS RECALLING CERTAIN MODEL YEAR 2008-2010 TRUCKS EQUIPPED WITH TRW STEERING SHAFTS. THE CIRCUMFERENTIAL WELD AROUND THE STEERING SHAFT TUBE THAT WELDS THE SPLINED TUBE TO THE NON-SPLINED TUBE MAY BE MISLOCATED. MISLOCATION OF THE CIRCUMFERENTIAL WELD MAY ALLOW THE SPLINED TUBE AND NON-SPLINED TUBE TO ROTATE RELATIVE TO ONE ANOTHER DURING A LOW SPEED, HIGH TORQUE TURN, POSSIBLY RESULTING IN A SEPARATION OF THE TWO TUBES. Remedy: DEALERS WILL INSPECT THE STEERING SHAFT USING A WELD PLACEMENT GAUGE PROVIDED BY TRW. ANY STEERING SHAFT FOUND TO HAVE BEEN WELDED IMPROPERLY WILL BE REPLACED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JULY 30, 2010. OWNERS MAY CONTACT KENWORTH AT 425-828-5440 AND PETERBILT AT 940-591-4196.
CERTAIN TRUCKS EQUIPPED WITH EATON SYNFLEX ECLIPSE BRAND EXTRUDED NYLON AIR BRAKE HOSE TUBING FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 106, "BRAKE HOSES." THE TUBING WAS MANUFACTURED WITH ONLY FOUR LAYERS OF NYLON MATERIAL, INSTEAD OF THE SPECIFIED FIVE LAYERS. Remedy: DEALERS WILL INSPECT THE AIR BRAKE HOSES AND, IF NECESSARY, REPLACE THE HOSES. THE RECALL BEGAN ON FEBRUARY 22, 2008. OWNER NOTIFICATION SCHEDULE FOR THIS CAMPAIGN. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440 OR PETERBILT AT 1-940-591-4196.
PACCAR IS RECALLING 318 MY 2007-2009 KENWORTH T800, W900, AND PETERBILT 357, 365, 367, 378, 379, 384, 385, 386,388, AND 389 TRUCKS EQUIPPED WITH PREMIER TRAILER HITCH ASSEMBLIES. THE PINTLE HITCH ASSEMBLIES MAY HAVE BEEN MANUFACTURED IN A MANNER RESULTING IN A REDUCTION OF FATIGUE STRENGTH OF THE PIVOT PINS. Remedy: DEALERS WILL REPLACE THE POTENTIALLY DEFECTIVE PIVOT PIN FREE OF CHARGE. THE RECALL BEGAN ON APRIL 18, 2008. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440 OR PETERBILT AT 1-940-591-4196.
ON CERTAIN KENWORTH AND PETERBILT HEAVY DUTY TRUCKS EQUIPPED WITH TAS-85 TRW STEERING GEARS, THE INNER SURFACE OF THE OUTER SECTOR SHAFT TEETH OF THE STEERING GEARS MAY HAVE AN INCORRECT INVOLUTE PROFILE, WHICH MAY LEAD TO CHIPPING AND DAMAGE OF THE GEARING SYSTEM. Remedy: DEALERS WILL REPAIR AND REPLACE ANY SUSPECT TAS-85 STEERING GEAR ASSEMBLY FREE OF CHARGE. THE RECALL BEGAN ON JANUARY 9, 2008. OWNERS MAY CONTACT KENWORTH AT 425-828-5440 AND PETERBILT AT 940-591-4201.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Issue: On certain trucks, the warning light for the tractor anti-lock brake system (ABS) may not turn on if the system loses power. If this happens, the driver will not get warning that the ABS is not working properly. Note: This problem would also cause the traction control (TC) and electronic stability control (ESC) lights not to turn on. Safety Risk: If a driver is not warned that the ABS is not working properly, there could be an increased risk of a crash. Corrective Actions: PACCAR will notify owners by mail and instruct you to take your truck to a dealer to update the software for the cab control module (CECU).
Certain vehicles fail to comply with the requirements of Canada Motor Vehicle Safety Standard 120 - Tire Selection and Rims. The tire information label may indicate incorrect tire pressure, understated by 5 PSI, or a tire/rim/inflation pressure combination for which the maximum GAWR is slightly below the GAWR of the vehicle. Underinflated tires may not be capable of supporting the maximum load as reflected by the GAWR and GVWR specified on the certification label, which could cause tire failure resulting in injury and/or damage to property. Correction: Manufacturer will mail new tire and rims certification label.
Certain vehicles fail to comply with the requirements of Canada Motor Vehicle Safety Standard 121 - Air Brake Systems. Incorrect brake linings were used on front drum brake assemblies fitted with large diameter tires (Static Load Radius of 20.5" - 21.5"), rendering the vehicles noncompliant to the standard. This could result in inadequate braking, increasing stopping distances and increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will install new brake shoes with the correct linings.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
On certain vehicles equipped with a PACCAR MX engine, the oil module centrifugal spinner filter cap may become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto nearby exhaust components. The discharge of engine oil onto hot exhaust components could result in a fire causing property damage and/or personal injury. Correction: Dealers will re-torque the oil module filter cap and install a secondary retention device on the secondary centrifugal spinner filter cap.
On certain vehicles, the bearing surfaces of the extended lube universal joint that attaches the inter-axle driveline to the drive axle may become prematurely worn due to breakdown of the lubrification and/or excessive heat. Prematurely worn bearing surfaces may result in the u-joint becoming loose and/or binding. If undetected, the condition may result in universal joint failure, allowing the inter-axle driveline to detach from the axle, which may cause the vehicle to become disabled in the roadway. Lost propulsion, in conjunction with traffic, road conditions, and the driver's reactions, could increase the risk of a crash. In addition a driveline component separating from the vehicle could strike another vehicle, stationary object, or bystander, causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the interaxle driveline universal joint.
On certain trucks, the inadequate stiffness of the Diesel Particulate Filter (DPF) bracket could result in the separation of the DPF from the chassis, which could result in personal injuries or death to motorists or bystanders. Correction: Caterpillar dealers will replace bracket as necessary.
Certain vehicles may have been assembled with an incorrectly manufactured Bendix MV-3 dash control valve. If the double check valve becomes lodged, in the event of a primary reservoir failure, air pressure can leak past the lodged valve, thereby depleting the secondary reservoir, causing a reduced ability for modulating the emergency brakes. Extended stopping distances may result in a vehicle crash, causing property damage, and/or personal injury or death. Correction: Dealers will inspect and, if necessary, replace the dash control valve.
On certain vehicles, the door latch may have been manufactured incorrectly. If the latch rotor cracks, the latch would not have primary or secondary closing security. Attempting to drive a vehicle with a door in the unlatched position can result in increased risk of injury to an unbelted front seat occupant. Correction: Dealers will inspect and, if necessary, replace the latch assemblies.
Certain vehicles fail to comply with requirements of CMVSS 121 - Air Brake System. The air lines were incorrectly constructed with only four layers of extruded nylon material, instead of the specified five layers. Should the air lines develop a leak, while the vehicle is in motion, it could cause the air brake system to fail, which would engage the rear spring brakes, slowing the vehicle to a stop, and preventing it from being driven. Correction: Dealers will inspect and, if required, replace the air lines.
On certain trucks, an incorrectly manufactured steering gear sector shaft may cause the steering to "stick or bind". This could severely restrict the steering turning angle, possibly resulting in a vehicle crash with injury or death. Correction: Dealers will replace the steering gear assembly.
On certain trucks, the fuel tank's longitudinal seams may have been fabricated using an incorrect weld speed for the given material thickness. This error resulted in a weld which did not completely penetrate the entire material thickness. Fuel tanks possessing this defect could leak diesel fuel in the event of a vehicle crash. A fuel leak, in the presence of an ignition source, could result in a fire. Correction: Dealers will inspect and replace any defective fuel tank.