Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2008 Sterling A-Line, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
CERTAIN FREIGHTLINER SCHOOL BUS CHASSIS, HEAVY TRUCKS, AND THOMAS BUILT SCHOOL BUSES MANUFACTURED BETWEEN JULY 2002 AND JULY 3, 2007, EQUIPPED WITH BENDIX SR-7 SPRING BRAKE CONTROL VALVES. THE PARKER SCV BRASS 90 DEGREE SINGLE CHECK VALVES (SCV) WHICH ATTACH TO THE SUPPLY PORT OF A BENDIX SR-7 SPRING BRAKE MODULATING VALVE CAN BREAK APART. PIECES OF THE PARKER SCV CAN BECOME LODGED INSIDE THE SR-7 SPRING BRAKE MODULATING VALVE, POTENTIALLY CAUSING EITHER LEAKAGE OUT OF THE SR-7 VALVE OR PREVENTING AIR FROM PROPERLY EXHAUSTING FROM THE SR-7 VALVE. ALSO, DUE TO A MANUFACTURING DEFECT IN THE INTERNAL RUBBER CHECK VALVE INSIDE THE SR-7 SPRING BRAKE MODULATING VALVES, THE VALVES CAN BECOME DEFORMED AND NOT SEAT PROPERLY. Remedy: FREIGHTLINER WILL NOTIFY OWNERS AND REPAIR THE VEHICLES FREE OF CHARGE. THE RECALL BEGAN ON JANUARY 11, 2008 TO FREIGHTLINER, STERLING, AND FREIGHTLINER CUSTOM CHASSIS OWNERS; TO THOMAS BUILT BUS OWNERS ON FEBRUARY 1, 2008. OWNERS CAN CONTACT FREIGHTLINER AT 1-800-547-0712.
ON CERTAIN TRUCK-TRACTORS EQUIPPED WITH HOLLAND SIMPLEX SE OR SE II FIFTH WHEELS, THE LATCH LEVER PIVOT BOLT ASSEMBLY MAY HAVE BEEN OVER-TIGHTENED WHICH COULD DISTORT THE PIVOT BOLT SPACER SLEEVE. CORROSION OR CONTAMINATES IN THE PIVOT MAY CAUSE IT TO BIND AND PREVENT THE FIFTH WHEEL JAW FROM LATCHING SECURELY AROUND THE TRAILER KING PIN. Remedy: DEALERS WILL REPLACE THE PIVOT BOLT AND SLEEVE WITH A HEX HEAD SHOULDER BOLT AND WASHER. THE RECALL BEGAN ON JANUARY 3, 2008. OWNERS MAY CONTACT FREIGHTLINER AT 1-800-547-0712.
ON CERTAIN TRUCKS EQUIPPED WITH TRW STEERING GEARS, MODELS TAS85 AND RCS85, THESE STEERING GEARS CONTAIN POTENTIALLY DEFECTIVE SECTOR SHAFTS WITH AN INCORRECT GEAR TOOTH WHICH MAY INTERFERE WITH THE RACK-PISTON TEETH, RESULTING IN A STICK OR BIND CONDITION. Remedy: FREIGHTLINER IS WORKING WITH TRW TO REPLACE THE DEFECTIVE STEERING GEAR (PLEASE SEE 07E101). THE RECALL BEGAN ON APRIL 18, 2008. OWNERS MAY CONTACT FREIGHTLINER AT 1-800-547-0712.
ON CERTAIN TRUCKS EQUIPPED WITH TUFTRAC REAR SUSPENSIONS, THE CENTER CASTING BRACKETS MAY BE OUT OF SPECIFICATION. AN OUT OF SQUARE CASTING MAY HAVE UNACCEPTABLE STRESS IN THE BRACKET WHEN IT IS INSTALLED AND MAY CAUSE IT TO CRACK IN SERVICE. Remedy: DEALERS WILL INSPECT AND CASTINGS THAT ARE OUT OF SPECIFICATION WILL BE REPLACED FREE OF CHARGE. THE RECALL BEGAN ON DECEMBER 12, 2007. OWNERS MAY CONTACT FREIGHTLINER AT 1-800-547-0712.
ON CERTAIN TRUCKS BUILT WITH AXILOK REAR WHEEL SPINDLE NUTS, THE NUTS MAY HAVE BEEN IMPROPERLY INSTALLED, WITH ONE OR BOTH LOCKING CLIP TABS NOT PROPERLY ENGAGED OR DAMAGED. Remedy: DEALERS WILL INSPECT THE AXILOK NUTS FOR LOCKING CLIP ENGAGEMENT OR DAMAGE. THEY WILL BE ADJUSTED OR REPLACED FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 10, 2007. OWNERS MAY CONTACT FREIGHTLINER AT 800-547-0712.
FREIGHTLINER IS RECALLING CERTAIN SCHOOL BUS CHASSIS, HEAVY TRUCKS, VAN CHASSIS, RV MOTORHOME CHASSIS MANUFACTURED FROM JANUARY 5 TO MAY 17, 2007, EQUIPPED WITH AXLE ALLIANCE COMPANY (AAC) FRONT AXLES. DURING THE FRONT AXLE ASSEMBLY, THE FASTENERS THAT ATTACH THE STEERING ARM OR TIE ROD ARMS TO THE SPINDLE MAY BE OVER OR UNDER TIGHTENED. Remedy: THOMAS BUILT WILL NOTIFY OWNERS, INSPECT THE FASTENERS, AND REPLACE THE STEERING ARM IF NECESSARY. THE RECALL BEGAN ON DECEMBER 21, 2007. OWNERS CAN CONTACT FREIGHTLINER AT 1-800-547-0712.
DAIMLER TRUCKS IS RECALLING CERTAIN MODEL YEAR 2006-2012 FREIGHTLINER BUSINESS CLASS M2, CASCADIA, CENTURY, COLUMBIA, CORONADO AND STERLING A-LINE VEHICLES BUILT WITH MERITOR WABCO ELECTRONIC STABILITY CONTROL (ESC) SYSTEM MANUFACTURED FROM SEPTEMBER 15, 2005 THROUGH SEPTEMBER 1, 2011. UNDER CERTAIN ROAD AND DRIVING CONDITIONS, VEHICLE BODY ROLL AND ROAD INCLINATION CHARACTERISTICS MAY ADVERSELY AFFECT THE SLIP ANGLE CALCULATION OF THE ELECTRONIC STABILITY CONTROL (ESC) SYSTEM. THIS MIGHT CAUSE THE ESC TO PERCEIVE AN OVER STEERING SITUATION AND THEREFORE APPLY THE OUTER WHEEL BRAKE ON THE FRONT AXLE UNTIL THE VEHICLE IS PERCEIVED TO BE STABLE. Remedy: DAIMLER TRUCKS WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE ESC MODULE WITH THE APPROPRIATE SOFTWARE VERSION AS NECESSARY, FREE OF CHARGE. AN INTERIM OWNER NOTIFICATION WILL BE MAILED ON OR ABOUT NOVEMBER 21, 2011. THE DATE FOR AVAILABILITY OF THE FINAL REMEDY IS SUBJECT TO VALIDATION TESTING AND PARTS AVAILABILITY. THE SAFETY RECALL BEGAN ON MARCH 28, 2012. OWNERS MAY CONTACT DAIMLER TRUCKS TOLL-FREE AT 1-800-547-0712.
DTNA IS RECALLING CERTAIN MODEL YEAR 2008-2012 FREIGHTLINER; CASCADIA, CENTURY CLASS, COLUMBIA, AND CORONADO, CERTAIN MODEL YEAR 2008-2009 STERLING; A-LINE AND L-LINE AND CERTAIN MODEL YEAR 2009-2012 WESTERN STAR CONSTELLATION VEHICLES, MANUFACTURED FROM JANUARY 14, 2008, THROUGH JUNE 15, 2011, BUILT WITH DETROIT DIESEL 15 OR 16 ENGINES. THE BOLT ATTACHING A RUBBER ISOLATOR TO A SUPPORT BRACKET MAY BECOME LOOSE AND BACK OUT, POTENTIALLY CONTACTING AN UN-FUSED STARTER CABLE AND CREATING A SHORT CIRCUIT. Remedy: DEALERS WILL INSTALL A NEW BOLT AND ISOLATOR AND REPAIR THE RECREATIONAL VEHICLES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON DECEMBER 21, 2011. OWNERS MAY CONTACT DTNA AT 1-800-547-0712.
DAIMLER TRUCKS IS RECALLING CERTAIN MODEL YEAR 2004 THROUGH 2008 HEAVY TRUCKS MANUFACTURED FROM JULY 11, 2003, THROUGH SEPTEMBER 28, 2007, EQUIPPED WITH EPA04 MODEL MBE4000 ENGINES BUILT WITH PLASTIC LOW PRESSURE FUEL LINES AND FUEL FILTERS MOUNTED NEAR THE CENTER OF THE ENGINE ON THE LEFT-HAND SIDE. THE PLASTIC LOW PRESSURE FUEL LINE BETWEEN ENGINE MOUNTED FUEL FILTER AND ENGINE BLOCK MAY DEVELOP A SUBSTANTIAL DIESEL FUEL LEAK. Remedy: DAIMLER TRUCKS WILL NOTIFY OWNERS AND THE REMEDY WILL BE PERFORMED BY DETROIT DIESEL CORPORATION AUTHORIZED REPAIR FACILITIES. VEHICLES WILL BE INSPECTED AND THE PLASTIC LOW PRESSURE FUEL LINE WILL BE REPLACED WITH A STEEL LOW PRESSURE FUEL LINE. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. AN INTERIM LETTER WAS MAILED TO OWNERS ON OCTOBER 28, 2011. THE SAFETY RECALL BEGAN ON FEBRUARY 21, 2012. OWNERS MAY CONTACT DAIMLER TRUCKS AT 1-800-547-0712.
DAIMLER TRUCKS IS RECALLING MODEL YEAR 2004-2010 TRUCKS EQUIPPED WITH CATERPILLAR C15 ENGINE. THE VARIABLE VALVE ACTUATION OIL LINE MAY RUB AGAINST THE P-CLIPS RETAINING THE OIL LINE, CAUSING AN OIL LEAK. Remedy: DAIMLER TRUCKS IS WORKING WITH CATERPILLAR TO REMEDY THESE VEHICLES. PLEASE SEE CATERPILLAR'S DEFECT REPORT 09E-020. CATERPILLAR WILL INSPECT AND REPAIR THE NECESSARY COMPONENTS FREE OF CHARGE. THE RECALL BEGAN ON MAY 5, 2009. OWNERS MAY CONTACT CATERPILLAR TOLL-FREE AT 1-800-447-4986 OR DAIMLER TRUCKS AT 1-800-547-0712.
CATERPILLAR IS RECALLING 14 MY 2008-2009 STERLING A-LINE & L-LINE TRUCKS EQUIPPED WITH CATERPILLAR ENGINE. THE AFTERTREATMENT REGENERATION DEVICE (ARD) MAY DEVELOP A HOLE AND HEAT AND FLAME MAY ESCAPE DURING A REGENERATION OF THE DIESEL PARTICULAR FILTER. Remedy: DAIMLER TRUCKS IS WORKING WITH CATERPILLAR (PLEASE SEE 08E-069). OWNERS MAY CONTACT CATERPILLAR AT-1-800-447-4986 OR DAIMLER TRUCKS AT 1-800-547-0712.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain trucks, the plastic low-pressure fuel line between the engine-mounted fuel filter and the engine block may develop a diesel fuel leak. The location of the leak is unlikely to result in a vehicle fire; however, diesel fuel spilt on the roadway could endanger other road users by making the roadway unexpectedly slippery. This could ultimately result in a vehicle crash causing property damage and/or personal injury. Correction: Dealers will replace the plastic low-pressure fuel line with a steel version.
On certain vehicles, specific operating conditions (such as tight, successive, highly banked curves in opposite directions), could trigger unintended Electronic Stability Control (ESC) system intervention. As a result, the ESC may unnecessarily apply one of the front brakes in order to correct the perceived oversteer condition. This may cause the vehicle to deviate from the intended path, thereby increasing the risk of a crash causing property damage and/or personal injury. Correction: Dealers will replace the ESC module.
On certain trucks equipped with a DD15 or DD16 engine, the bolt attaching a rubber isolator to a support bracket may become loose, back out, and contact the starter cable. This could cause an electrical short, which could result in a fire causing property damage and/or personal injury. Correction: Dealers will install a new bolt and isolator, and apply thread-locking fluid to the fastener.
On certain vehicles equipped with a Caterpillar C15 engine, the Variable Valve Actuation (VVA) oil line may wear against the P-clip retaining the oil line. An oil leak could result in a vehicle fire causing property damage and/or personal injury. Correction: Caterpillar dealers will replace the VVA oil line with an updated version.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
On certain trucks, an incorrectly manufactured steering gear sector shaft may cause the steering to "stick or bind". This could severely restrict the steering turning angle, possibly resulting in a vehicle crash with injury or death. Correction: Dealers will replace the steering gear assembly.
On certain trucks, the fifth wheel hitch assembly's lever arm may have been incorrectly installed during the manufacturing process. The lever arm pivot bolt may have been over-tightened which could distort the pivot bolt spacer sleeve and prevent the fifth wheel latch jaw from closing and latching securely around the trailer king pin. This could allow the towed unit to separate from the towing vehicle while underway, potentially causing a crash with injury or death. Correction: Dealers will replace the pivot bolt and sleeve with a hex head shoulder bolt and washer.
On certain trucks, improper installation procedures may have damaged one or both locking tabs on the rear wheel spindle nut during vehicle assembly. Damage to the locking clip tabs reduces the nut's ability to resist rotation possibly allowing the nut to back off and the dual wheel set to become separated from the vehicle. If this happens, the vehicle may become difficult to control, leading to a crash with injury or death. In addition, the separated wheel assembly may pose a risk to other road users or bystanders. Correction: Dealers will inspect and replace damaged spindle nuts.
On certain vehicles, the fasteners that attach the steering arm or tie rod arm to the spindle may have been over or under tightened during assembly process. Incorrectly torqued steering arm fasteners may fatigue and fracture, possibly causing a crash without warning. Correction: Dealers will inspect fasteners and apply correct tightening torque.
On certain trucks, the flange, crossmember, and web mounting surfaces of the center suspension mounting bracket casting may not be perpendicular. An out of square casting may have unacceptable stresses in the bracket when it is installed and may cause it to crack in service. The driveline may not be held in position if a cracked bracket fractures completely. This will affect vehicle control and may cause a crash without warning. Correction: Dealers will replace casting out of specs.
On certain vehicles, the internal rubber check valve inside the Bendix SR-7 spring brake modulating valve can become deformed over time. The effect of this defect is intermittent and presents a potential delay or failure in applying the parking brakes; potentially resulting in a vehicle roll away. Should this occur, the unattended roll away vehicle could strike a bystander or cause property damage. Correction: Dealers will install a check valve repair kit.