Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2008 Toyota Matrix, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2008 COROLLA AND COROLLA MATRIX VEHICLES. THE ENGINE CONTROL MODULE (ECM) FOR THE SUBJECT MODELS EQUIPPED WITH THE 1ZZ-FE ENGINE AND TWO-WHEEL DRIVE MAY HAVE BEEN IMPROPERLY MANUFACTURED. THERE IS A POSSIBILITY THAT A CRACK MAY DEVELOP AT CERTAIN SOLDER POINTS OR ON VARISTORS ON THE CIRCUIT BOARD. Remedy: DEALERS WILL INSPECT THE PRODUCTION NUMBER OF THE ECM AND REPLACE THE ECM IF NECESSARY. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. TOYOTA WILL MAIL AN INTERIM OWNER NOTIFICATION THE MIDDLE OF SEPTEMBER 2010 TO ADVISE OWNERS OF THIS DEFECT AND RECALL. THIS INTERIM NOTIFICATION WILL INFORM OWNERS THAT THEY WILL RECEIVE A FUTURE NOTIFICATION WHEN PARTS BECOME AVAILABLE TO HAVE THE FREE REMEDY PERFORMED ON THEIR VEHICLE. THE SAFETY RECALL BEGAN ON NOVEMBER 29, 2010. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
GULF STATES TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2010 VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD BETWEEN SEPTEMBER 1, 2005 AND JUNE 2, 2008 WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS. Remedy: DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. DEALERS WILL ALSO CORRECT THE OWNER'S MANUAL. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT GULF STATES TOYOTA AT 713-580-3300.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Issue: This recall is for certain block heater kits installed on certain vehicles or sold as accessories at Toyota or Lexus dealerships. On certain vehicles, the engine block heater cable may not have enough heat protection and could be damaged by high temperatures. If this happens, the cable could short circuit while plugged in, and cause the wiring to overheat or melt. Note: This recall only affects the following block heater/cord part numbers: C014003034 PK5A408J09 PU14000904 C014003151 PK5A408J13 PU14000905 C014000885 PK5A489J11 PU14000907 C014000888 PK5A489J22 PU14000909 C014000907 PK5A410H00 PU14000911 C014100904 PU14000900 PU14000913 C014100907 PU14000901 PU14003571 C014100911 PU14000902 PK5A489J14 PK5A408J05 PU14000903 Safety Risk: Engine block heater wiring that overheats or melts could create the risk of a fire. Corrective Actions: Toyota recommends that you should stop using the engine block heater immediately. Toyota will notify owners by mail and instruct you to take your vehicle to a dealer to disable the engine block heater. For some vehicles, the corrective actions for this recall are under development. For others, a new engine block heater cannot be installed, and the owner will receive a refund of the purchase price of the engine block heater.
Issue: On certain cars, the passenger-front airbag that was installed during prior recall repair must be replaced. The airbag may not unfold properly when it deploys. This could cause the airbag to tear or not inflate properly in a crash. Safety Risk: An airbag that does not work properly could create an increased risk of injury in a crash. Corrective Actions: Toyota will notify owners by mail and instruct them to take their vehicle to a dealer to replace the passenger-front airbag assembly.
We checked the EU Safety Gate for recall alerts naming this model and its production years.
Source: EU Safety Gate (European Commission) · CC BY 4.0, © European Union
The gas generator of the passenger airbag may be defective. This may result in uncontrolled inflation, causing injuries to the occupants. Production: The affected vehicles were manufactured between January 2002 and January 2008.. Types: Type-approval number: individual approval.
The gas generator of the passenger airbag may be defective. Production: The affected vehicles were manufactured between 6 January 2002 and 13 December 2007.. Types: Type-approval number: individual approval.
Production dates not stated in the alert. Types: The vehicles in question were manufactured between 28 December 2001 and 3 May 2004..
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Crash-test ratings from NHTSA's New Car Assessment Program.
Source: NHTSA (US Department of Transportation) · US public domain
On certain vehicles, long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, could eventually degrade the propellant contained in the passenger frontal airbag. This could cause the airbag to deploy with more force than normal. As a result, if the vehicle were involved in a collision that warrants airbag deployment, fragments could be propelled toward vehicle occupants, and the airbag assembly could be damaged, preventing proper function. These issues could increase the risk of injury. Correction: Dealers will replace the passenger frontal airbag assembly. <br><br> Note: Canadian climate results in the propellant degrading slowly. The recall is being conducted as a precaution to address future risk, and is expected to replace airbag inflators before their function would be affected. Matrix model vehicles may have had the original front passenger airbag inflator replaced as a “like-for-like” replacement under a previous recall as a temporary remedy while evaluating a permanent remedy. These vehicles will receive the permanent remedy passenger airbag assembly under this recall.
On certain vehicles, the passenger (frontal) airbag inflator could produce excessive internal pressure during airbag deployment. Increased pressure may cause the inflator to rupture, which could allow fragments to be propelled toward vehicle occupants, increasing the risk of injury. This could also damage the airbag module, which could prevent proper deployment. Failure of the passenger airbag to fully deploy during a crash (where deployment is warranted) could increase the risk of personal injury to the seat occupant. Note: This recall supersedes recalls 2013113, 2014224, 2015197 and 2015269. Correction: All vehicles having not received a replacement inflator as part of the previous recall will now have a replacement inflator installed by dealers. For Matrix model vehicles, dealers may replace the front passenger airbag assembly with one equipped with a newly specified inflator.
On certain vehicles equipped with a 1ZZ-FE engine and a two-wheel drive transmission, the Engine Control Module (ECM) may have been improperly manufactured. There is a possibility that a crack may develop at certain solder points or on varistors on the circuit board. In most cases, if a crack occurs at certain points or on certain varistors, the engine warning lamp could be illuminated, harsh shifting could result, or the engine may not start. In limited instances, if cracking occurs on particular solder points or varistors, the engine could stop while the vehicle is being driven, increasing the risk of a crash causing personal injury. Correction: Dealers will inspect and, if necessary, replace the ECM.