Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2008 Volvo VNL, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
Volvo Trucks North America (Volvo) is recalling certain model year 2007-2014 VAH, VHD, VNL, VNM, and VT models. The affected vehicles were built without a redundant clutch disengagement switch. Without a redundant switch, a loss of signal from the brake air pressure switch can prevent the clutch from automatically disengaging when the brake is applied. Remedy: Volvo Trucks will notify owners and dealers will inspect and repair the vehicles if necessary. The recall began on August 26, 2013. Volvo's recall number is RVXX1303. Owners may contact Volvo at 1-336-393-2000.
VOLVO TRUCKS IS RECALLING 366 MY 2006-2009 VNL TRUCKS EQUIPPED WITH SUPER SINGLE TIRES, BENDIX BRAKE CAM TUBES, AND VOLVO AIR SUSPENSION. THE VIBRATION FREQUENCY FROM THE SUSPENSION WITH SUPER SINGLE TIRES MAY RESULT IN A FATIGUE CRACK OF THE MOUNTING BRACKETS FOR THE BRAKE CAM TUBE. Remedy: DEALERS WILL ADD A SUPPORT BRACKET TO THE BRAKE CAM TUBE. THE RECALL BEGAN ON JUNE 30, 2009. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
ON CERTAIN TRUCKS, AN INCORRECT SOFTWARE PARAMETER WAS LOADED WHICH RESULTED IN THE DIESEL PARTICULATE FILTER (DPF) 'INHIBIT' FUNCTION BEING DISABLED. THE 'INHIBIT' FUNCTION IS A MEANS FOR THE DRIVER TO STOP A DPF REGENERATION FROM OCCURRING IF A VEHICLE IS IN A LOCATION THAT MAY PRESENT A HAZARDOUS SITUATION. Remedy: DEALERS WILL CHANGE THE CONTROL PARAMETERS. THE RECALL BEGAN ON FEBRUARY 15, 2008. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
VOLVO TRUCKS IS RECALLING 127,764 MY 2001-2008 VHD, VNL, VNM, AND MY 2005-2008 VT TRUCKS. A SEAL MAY FAIL ALLOWING WATER AND CONTAMINANTS TO SEEP INTO THE WINDSHIELD WIPER MOTOR. Remedy: VOLVO WILL REPLACE THE WIPER MOTOR FREE OF CHARGE. SINCE THIS RECALL INVOLVES A LARGE NUMBER OF VEHICLES, VOLVO WILL RELEASE THE RECALL IN STAGES AS PARTS ARE RECEIVED. PRIORITY WILL BE GIVEN TO THE VEHICLES LOCATED IN THE REGIONS/STATES THAT HAVE A CORROSIVE ENVIRONMENT. THE RECALL BEGAN ON SEPTEMBER 30, 2009. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
VOLVO IS RECALLING CERTAIN MODEL YEAR 2008-2011 VHD, VNL, VNM, AS WELL AS 2008-2010 VT VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF PART 567, "CERTIFICATION." THE TIRE DESCRIPTION MAY BE INCORRECT ON THE VEHICLE'S CERTIFICATION LABEL. Remedy: DEALERS WILL INSPECT AND REPLACE THE LABELS FREE OF CHARGE. THE SAFETY RECALL BEGAN ON FEBRUARY 25, 2011. OWNERS MAY CONTACT VOLVO AT 1-800-458-1552.
ON CERTAIN TRUCKS, THE HOOD RESTRAINT CYLINDER DOES NOT CONTAIN ENOUGH DAMPENING TO ADEQUATELY RESTRAIN THE HOOD. Remedy: DEALERS WILL REPLACE THE HOOD RESTRAINT CYLINDERS FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 15, 2007. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
ON CERTAIN HEAVY DUTY TRUCKS, THE CIRCUIT PROTECTION (I.E. AUTOMATIC CIRCUIT BREAKERS) USED TO PROTECT THE VEHICLE LIGHTING SYSTEM MAY NOT PROVIDE ADEQUATE PROTECTION. Remedy: DEALERS WILL REPLACE THE CIRCUIT BREAKERS WITH FUSES. THE RECALL BEGAN ON FEBRUARY 25, 2008. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
ON CERTAIN TRUCKS, AN UNPROTECTED LEAD IN THE THERMOSWITCH OF THE HEATER MAY MAKE CONTACT WITH ANOTHER POST POSSIBLY CREATING A SHORT CIRCUIT, WHICH CAN RESULT IN CONTINUOUS OPERATION OF THE HEATING ELEMENT. Remedy: DEALERS WILL INSPECT THE THERMOSWITCH AND WILL REPLACE IT IF NECESSARY. THE RECALL BEGAN ON SEPTEMBER 10, 2007. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
ON CERTAIN TRUCKS EQUIPPED WITH A SAF HOLLAND SIMPLEX FIFTH WHEEL, THE LEVER ARM PIVOT BOLT MAY HAVE BEEN OVER TIGHTENED. AN OVER TIGHTENED PIVOT BOLT CAN DISTORT THE PIVOT BOLT SPACER SLEEVE, WHICH MAY PREVENT THE FIFTH WHEEL LATCH JAW FROM CLOSING AND LATCHING SECURELY AROUND THE TRAILER KING PIN. Remedy: DEALERS WILL REPLACE THE PIVOT BOLT AND SLEEVE WITH A HEX HEAD SHOULDER BOLT AND WASHER FREE OF CHARGE. THE RECALL BEGAN ON JANUARY 28, 2008. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
ON CERTAIN TRUCKS, THE BOLTS THAT ATTACH THE STEERING GEAR TO THE FRAME MAY NOT HAVE BEEN TIGHTENED TO THE SPECIFIED TORQUE. Remedy: DEALERS WILL TIGHTEN THE BOLTS FREE OF CHARGE. THE RECALL BEGAN ON DECEMBER 3, 2007. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
ON CERTAIN TRUCKS, THE NUT USED TO RETAIN THE STEERING SHAFT MAY OR MAY NOT BE A LOCK NUT THAT HAS THE LOCKING FEATURE. A LOCK NUT IS REQUIRED TO PROVIDE ADDITIONAL RESISTANCE TO ENSURE THAT THE NUT DOES NOT COME LOOSE. Remedy: DEALERS WILL REPLACE THE STEERING SHAFT PINCH BOLTS AND LOCKNUTS FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 24, 2007. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
ON CERTAIN TRUCKS, THE AXLE HOUSINGS MAY HAVE BEEN MANUFACTURED WITH STEEL THAT WAS OUT OF SPECIFICATION WHICH COULD RESULT IN A FATIGUE FAILURE OVER TIME. Remedy: DEALERS WILL REPAIR AND INSPECT THE AXLES AND REPLACE THEM FREE OF CHARGE. THE RECALL BEGAN ON APRIL 9, 2007. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain vehicles, the secondary clutch disengagement switch may have been omitted during vehicle assembly or, in some instances, removed during servicing. As such, primary switch failure would cause the automated manual transmission’s clutch to remain engaged when the brakes are applied. This could increase stopping distances, possibly resulting in a crash causing property damage and/or personal injury. Correction: Dealers will install a micro-switch at the brake pedal and update the software to run a diagnostic on the switch during engine start-up.
On certain vehicles, the tire description may be incorrect on the certification label, which is a non-compliance to Canada Motor Vehicle Safety Standard 120 - Tire Selection and Rims. The description listed on the label may be for a tire with a lower rating that cannot support the Gross Axle Weight Rating (GAWR) listed, which may result in a potential tire failure. Correction: Updated labels will be mailed to owners of affected vehicles, along with instructions for proper installation.
On certain vehicles, the windshield wiper motor may be susceptible to water intrusion, which could result in an electrical short circuit and a fire. This could cause property damage, personal injury or death. Correction: Dealers will affect repairs.
On certain trucks equipped with super single tires, vibration frequency from the suspension may result in fatigue cracking of the mounting brackets for the brake cam tubes. In time the crack could propagate and cause of the brake cam tube support bracket(s) to fail, which could result in a loss of brakes at the corresponding wheel end. This could increase stopping distances, possibly causing a vehicle crash resulting in property damage, personal injuries or death. Correction: Dealers will install an additional support bracket to the brake cam tubes.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
On certain trucks, incorrect software installed during vehicle assembly will cause the Diesel Particulate Filter (DPF) inhibit function to be disabled. As such, the driver may not be able to stop, or be aware that, DPF regeneration is occurring. Should this happen while the vehicle is in a location that presents a hazardous situation, it could result in a fire. Correction: Dealers will change electronic module control parameters.
On certain trucks, the automatic circuit breakers used to protect the vehicle lighting system may not provide adequate protection. If a short circuit occurs, components and wiring may be subject to overheating, which could result in a vehicle fire, causing property damage and/or personal injury or death. Correction: Dealers will replace the circuit breakers with fuses.
On certain trucks, the bolts that attach the steering gear to the frame may not have been tightened to the specified torque. This could allow the bolts to loosen and fall-out, possibly causing a loss of steering control and a crash with injury or death. Correction: Dealers will tighten the bolts to specs.
On certain trucks, the fifth wheel hitch assembly's lever arm may have been incorrectly installed during the manufacturing process. The lever arm pivot bolt may have been over-tightened which could distort the pivot bolt spacer sleeve and prevent the fifth wheel latch jaw from closing and latching securely around the trailer king pin. This could allow the towed unit to separate from the towing vehicle while underway, potentially causing a crash with injury or death. Correction: Dealers will replace the pivot bolt and sleeve with a hex head shoulder bolt and washer.
On certain vehicles, inadequate hood cylinder dampening may allow the hood to be opened with too much force. Once the cylinders reach full extension, this lack of dampening could cause them to separate from the hood, allowing the hood to keep tilting forward, possibly injuring its operator or a bystander. Correction: Dealers will replace the hood restraint cylinders.
On certain trucks, when the ignition key is in the 'ON' position, the pre-heater, located in the fuel filter base, is energized. If this pre-heater is energized while maintenance is being performed on the fuel filter, diesel fuel could ignite within the filter housing. A fire within the fuel filter housing may spread possibly resulting in property damage or personal injury. Correction: Dealers will inspect and, if required, replace the fuel heater assembly.
On certain trucks, the locknut used to retain the steering shaft may not have had the lock feature. As a result, the nut could loosen, allowing the steering shaft to separate, causing a loss of steering control which could result in a vehicle crash with injury or death. Correction: Dealers will replace the steering shaft pinch bolt and locknut.
On certain trucks, the axle housing may have been manufactured with steel that was out of specification (9.5mm thick instead of 11mm thick), which could result in a fatigue failure over time. If failure occurs, the axle may lock-up or the end of the axle could come off, which may result in a vehicle crash with injury or death. Correction: Dealers will inspect and, if required, replace the axles.